Zach Moore (@slackmoore) and I show and test five knots that are hard to find on the internet. The unfinished 9, the scorpion hitch, bernese anchor, double girth hitch (or bGebz) and BFK (big fat knot).
After tensioning the unfinished 9 at (10.15kN or 2282LBF) Zach and I tried to untie the knot. With no success we tried again at a tensioning force of 4.2kN. After testing the sketchy unfinished 9 (A KNOT THAT SHOULDN'T BE USED) we then show you more creative ways of anchoring with a few girth hitch variations that are extremely useful and convenient. At last, moving on to highliner's favorite knot, the BFK and its tailless variation with a built in PAS.
Highline Anchors ebook is 80% but still available, it's free, and on the home page of https://www.slackline.com/ and the Knots can be found starting on page 62
Hi I'm Ryan Jenks and there's no one more better than Zach here.
That's a pretty good one. I've been working on that.
We're going to show you some knots that I have found to be hard to find on the
internet. They're here and there and we'll put
the links of those other videos in the description below.
I was writing the highlining ebook on highlining anchors and we did a section
on how to be knotty. All the different knots that you use
when you're rigging highlines. But this applies to climbing, highlining
or any general use. These knots are pretty dang helpful
and we're going to go over them since they're not easily found on the
internet. Nor do they have puns. So let's get
started.
So let's talk about the unfinished nine. Now let's explain what a figure nine is.
Let's start with a figure eight. It looks like an eight. This is the most
common knot you pretty much see and this is what
you tie in at the climbing gym and most things you do.
A nine is if you go around one more time and it's supposedly a nine. But based on
that logic if you went around one less time this
would be a figure seven. But they call that an
overhand knot. Anyways I always find that interesting and
that is how you can remember how a figure nine is tied.
So we're going to go around and tie our figure nine.
Okay now an unfinished figure nine is where you just quite can't commit to the
knot. And I'm going to need a little bit more
rope than I have here. So I'm going to do that much and you go
around once and go around twice. And instead of
going through I'm going to put a bite or a loop through
and then I'm just going to bring this to the top to where they match. And you're
basically doing a basket hitch around this part of the knot.
And then once you dress it all up. Dressing your knot.
Then you have essentially is what an unfinished nine is.
The idea behind this is that it's easier to untie
and there's no sharp bend radiuses going on here.
Especially if I took the time to dress it. Now you can just consider
that all knots get 50% of the MBS of a rope. Ropes are brake tested
in labs with these big diverters or clamps
where it has no bend in it. It's the best case scenario you'll get for a rope.
And then everything beyond that how you use it is going to reduce it.
The easiest way to remember is you'll lose 50%.
Now we do this in slack lining sometimes because we think we get a
higher value than some of our alternative knots
when we tie a knot in our backup webbing.
But we don't want to get too much into the weeds on that. We are going to put
this on our slack set machine and we will put a figure eight on this
side right now. And we will see
if we can untie these after we put around 10 kilonewtons
on this right here and see if if we can untie them with a hammer or without a
hammer at all. Please don't use this knot. This is for
entertainment purposes only and if you only clip one side of this
you're going to die. Instead of going through here
I'm going to go around one more time and you're going to clip this one and
this one. Now in theory you could do an unfinished
figure eight but I think this looks fancy. Let's go
let's go give her a tug. Welcome to the slack lab.
This is our new one with carpet on the walls for less echo
and we've got our hydraulic system here. We have the unfinished nine on this side,
figure eight on this side, and our dynamometer. So let's take it up to
10 and we'll just let you watch it morph.
10.15 kilonewtons. That is pushing the limits. This thing is going to break
typically around 15. So we're going to back it off
and then we're going to see if we can untie it. So
this is entirely put back the way it was
and you can see how much it has stretched slash
pulled out of the knot. So it's very interesting that's why we started with
such a small sample. Is that eight really hard? No, this is
coming out.
Not budging? I don't think so. And if you could you probably wouldn't want to use
it when you're done. Is there a way to pull that through?
Zach, were you able to untie the unfinished nine?
We're gonna try testing it again but only going to four kilonewtons instead
of ten. Okay, something realistic. Something
realistic. Four. All right. 4.2 kilonewtons. This is
realistic. Now let's untie it. Does it pinch it
down? Yeah, in between the two. Right, because if you pull this knot
that's the one that would be like it's like a slip knot, right? But you
can't pull at this point. I think maybe this middle section a little
bit looser before I can pull that strand at all. It's pretty tight.
I might need a hammer for this one.
Even at four it's so hard. It's loosening. I can feel it with this
one. Yeah, just give a good massage. It should
come out. By the way, don't put ropes on oily
surfaces or asphalt or anywhere there might have been
acid. Oil doesn't seem to affect ropes too much that I've tested but
it's mostly battery acid so smashing this on a dirty ground has been a bad
example. Wow, that is very disappointing.
I was really expecting it to be easier. Yeah, no,
I'm over it, man. Yeah. You guys over it? Have I dragged this section on too long?
Let me drag it on just a little bit longer. Knots in
a backup line because it can be loose, right? So we're not tensioning it so we
don't need our web blocks. Yada yada. A lot of people have put
frost knots, myself included, and we debate on whether or not the line
should be on the outside or sandwiched on the inside, whatever.
My tests have shown it's all about the same
and what it is is it's like a doubled up loop as you can see here
tied in an overhand and flat webbing or flat rope
essentially is, I don't know, behaves a little bit differently. Overhands
tend to just be just as good as figure eights. The alternative, and this is where
figure nines kind of became popular in slacklining,
is where we actually have a better bend radius
if you take this extra bend there and it doesn't, it's bend radiuses that
reduce the strength. Does that give us better results than
this? It wasn't so much about untying it as
much as it was about strength. I just thought this would be easier to
untie. So let's take this up to six
kilonewtons because you can get that on a high line and see if
either one of these are something we can untie.
6.1! Smash your fingers and you will regret it.
So I was able to untie this one with a few whacks.
This is what I was expecting the rope to do.
That looks like, that doesn't look like it's coming undone.
I don't know if that knot's coming out.
I'm less fond of these now. Now I have done tests
of unfinished nines with webbing and frost knots. We've done quite a
few. I'll put links in descriptions on where
you can find that and tests that other people have done.
Let's move on to the next knot. So now I'm going to show you the scorpion hitch
which is basically a girth hitch on the back side of let's say a boulder
where the tail comes up over the top like a scorpion tail
and it actually puts your master point higher
than you can get if it was just wrapped or basketed
around the boulder. Welcome to my boulder. What I have here
is two span sets. Girth hitch together because
I don't have one long enough and for slackline use that is strong
enough. Now a basket is basically this.
It wraps around this is what we do around trees
every time we slackline. The alternative option
is to girth hitch it which keeps it... There's pros and cons to this. I don't
want to get too far into the weeds on that.
This is a girth hitch and this offers pros and cons.
Whenever you do have a girth hitch you are now reducing it 50% but I already
did that attaching two together with girth
hitches. Let me show you the scorpion trick.
You grab this and you go around the boulder. You make sure it's
nice and tight so it doesn't slip off the back side. You
have to pick rocks that you can do this with and then
here you have your master point at the very very top or if you put
a bag or something under it you're actually the highest point you can be.
Now let's talk about safety real quick. If
this was a boulder on a hill and you're pulling it this way don't do
that. Basket or not. If it's flat take into
consideration if it can be pulled over the top. You're putting a
lever on your boulder. Now if you're doing this on a boulder
that is on a hill but you're pulling over the
hill even at like just the slightest angle it'd be okay and you can use a
boulder let's say this size as one part of your anchor if you're
pulling it uphill. But if this is a boulder you're pulling
downhill I don't even think a boulder 10 times the size is the right answer.
Please be very mindful about what you're pulling on and how it's
attached to the ground.
For example that's a lot harder than that.
If you want to see us do some break tests and actually see what
boulder for boulder what happens if we do a basket
at what force it pulls versus what force a scorpion makes it start to move
we can do that put that in the comments below. Another thing you have to be
careful when you put force on it it wants to
to move. It wants to find center. You can't put this wherever you want.
It's going to be exactly in the middle of where you put that girth hitch.
Let me show you another spot this actually helps. Here's another spot it
can help. If you put the girth hitch on the back
side of the tree it can actually come through the crotch and
then it's stable it's here it's high you're actually
getting the strength of this thicker part while not having to
wrap like one of these side ones. This is an option for
many uses. I use scorpion wraps all the time.
I actually use this in reverse so it's like a girth hitch backwards backwards
it's kind of like inception where I did a reverse scorpion and went
under a boulder in order to test the cams the rigid stem cams that you can
see in this video here. There's a lot of times that it's nice
to have this master point at a different point than your wrapping
and in slacklining we call it the scorpion hitch. Okay now we're going to
show you how to do an adjustable sling. There actually is
no name for this which is funny. If you take a
proper size sling and you want to do a basket hitch
that is pretty perfect actually. You could do a girth hitch and that kind
of stays in place and it's not as likely to fall down the tree.
If you wanted to have less force and less bend on that
it's not going to stay up as well but if I was going this way
it's almost like a tensionless hitch where you wrap the rope around three
times and clip it to the thing. That is pretty much
not going to have as much of a reduction in strength.
I'm not too worried about the reduction of strength in a span set
or an industrial sling. Now if you have a longer span set like I have here
you will need to adjust it. My lasso skills man.
Okay this is ridiculous and so we want it a little bit
shorter and we don't want to double it up. If you
wanted it exactly half of what it was you can just
fold it in half and then go around the tree
and be a tree hugger and it's almost there.
If you did a carabiner it would tri-load it too much pulling it in three
directions. Pulling it this direction, this
direction, that direction. That could easily break a carabiner. This could
work. You're not going to break this setup
especially doubled up especially with this shackle.
This isn't going to break but it's not ideal.
You could also girth hitch it and you reduce
the span set down 50 percent of its doubled amount.
But what if you didn't want it exactly this tight?
Let me show you how to adjust that. So there's two ways to do this.
First way we'll show you the bernie's anchor
and what you do is you do a girth hitch and then you take the tail of it
and you wrap it around. So let's say I want it to stick out about here
go around here rotate it and that is not going to come off.
In order to show you more of the concept of this without this being wrapped
around the backside of the tree you take this guy
when you're crossing it will help it all orientate it.
But then this is pulling in this basket shape kind of like basketing the tree
but on the loop and so I don't think you're going to get too
much reduction in strength from this nor does that matter and you find
center and you can always scrunch this up and
adjust it. But there's also another way which is
like voodoo magic. Let me show you that. So what you can do
is just take one side of this and you kind of take this guy and you're
going to basket around itself.
Now I do believe this would reduce the strength
more than the other way and then this adjusts until it's even
and then you can flip this. This is really nice if you have like a scorpion
tail and you want to adjust one side where you can't just
girth hitch or bernie's knot the other way.
And if I want it shorter I just take these two strands
and they're going there and this is why you pad trees
because I am rubbing the crap out of this. That
is another way to adjust your sling and I'm sure you can do this with climbing
slings if you would like to see those brake
tested dyneema slings or nylon slings because sometimes they're just
too long and it's nice to use a double length for some things and then
it's too short if you doubled it up. Here's some nice tricks for that.
So let's move on to the next knot. Okay so we're going to show you how to do a
double girth hitch or a jibibi knot. I don't have an alpine
web block or a web block with a large eye with me
but if we wanted to fix something like a ring
or a web block for slacklining you can do that with this method.
So what you do is you put the item on the span set and you're going to girth
hitch it into the system. Now there's two methods to this.
Method one that you can see on Balance Community
is half the strength. So now one method is this way where you put it inside of
here and then you end up girth hitching kind
of the item through the same sling that it's on and this
actually reduces the strength 50 according to Balance Community's
tests and I mean it's okay for some things
but the other way does it at 70 percent and so method two
is instead of putting this in here you put this through here
and then stick your hand through the the side without the item
and grab the item and then you have girth hitched
that item in there. This is embedded into the system and it can't come off so if
you're low on connectors or I mean this is just
insanely bomber this is around 70 based on those tests.
All those links will be in the description below
and that is the double girth hitch or the BGBs knot.
And for the last knot we're going to show you a few BFKs or
big fat knots in order to kind of expand your mind on what you can do with them.
If you climb you can join two ends of a rope together
flip it to let's say a two-point anchor and this is pretty standard and common
instead of having like a sliding x you grab it make sure it's equalized and
then you tie a knot whether or not it's an overhand or a figure eight
it is considered a big fat knot and it isolates both strands
but in theory doesn't equalize as well. If you unclip one side it's still
bomber and ropes stretch so if you're using a
dyneema sling it won't work as good and it reduces the strength of your
dyneema sling quite a bit. I prefer just to do a sliding x with the
dyneema sling. If I'm climbing that is an open carabiner.
That's not what I want to show you. What I want to show you is the tailless
BFK which you can easily remember because this has
giant tails so you don't tie any knots first you just insert it
into the carabiners
and if you had a four-point anchor or a three-point anchor it all works the same
what you do is I want this to be here and then I can because my rope is so
big
do that and you pull down in between each carabiner
what I have here is the other side of the rope
so you take this and you go the opposite direction
this one goes this direction and what I'm going to do
is extend it find the direction of pull that I want to do
whether or not this is a climbing anchor with cams or a highline anchor
and then you tie your overhand or figure eight
now I'm going to add a little bit more rope because I need it to be out here
in order to tie my knot and get it to about right here when I'm done
but this takes up a lot of space and so I'm going to redo that
after fiddling with this I have a nice long tail which I'll show you what I'm
going to use that for in a minute I have this here all of these strands
seem to be equalized enough I prefer to have these a little bit looser these a
little bit tighter because of how equalization works
what I do is I'm going to tighten up the two outside strands
put a little bit less force on those middle ones
and I'm going to see if an overhand or figure eight is going to give me
the best situation looks like all I get is an overhand
either way it isolates all the strands
either way it's a big fat knot and what you can do is dress that
but it's not going to really affect the strength too much because
it is a big bend radius and that's what gives ropes
the most strength now I don't like to tighten this knot too much
because as you pull it in the direction it's going to go
it's going to let's say this is too loose here and it starts to cinch down
after you put a couple kilonewtons on that it's going to kind of
self-equalize and how much you can see how much that changes so I just kind of
let it do its own thing time fixes this stuff what's nice about
this is as opposed to a sliding x if one
strand comes undone on a sliding x the whole thing comes unraveled but if
one anchor point comes undone or a strand gets abraded through then
it's not going to fail entirely because it's now being
shared amongst these three and it's isolated and holding
now in this case this one's holding the most force
but it still equalizes enough to not be a problem
if you cut one of these strands it's redundant if you cut one of these
strands it's redundant and the abrasion tends to be here or
here and it's almost self-padded it's very
important to pad this if this was a highline anchor
or if this is just rubbing anything it's going to be bad
but when it's configured like this it's less bad
than if it was like a sliding x another trick you can do with this
is i added a lot of extra tail on this one side
and this is with a full rope by the way i'm going to re-tie this
i'm just going to do the overhand kind of dress it
not tightening it too much trying to get these strands to be as
even as possible then what you can do is take
this tail and trace it back through like you take
the tail of the rope that you tie in at the climbing gym
and trace it back through the figure eight that you
made on your harness because i want the tail to come out of the front
and why do i want that because now i can take this
and then i can tie a figure eight at the end on a figure eight on a bite
and just so nobody mistakes that end for anything
and then i have this personal anchor that's built into my system
and you can clip in and set it back there on the cliff
so nobody's near the edge without first clipping into this
and then walking this direction and it's like full strength
and can be shock loaded and stuff and you get full strength out of this rope
so this is a tailless bfk with giant tails
i don't know why it's called that if you know why it's called the tailless bfk
other than the tails aren't joined let me know this is not really
easily found on the internet uh once you get to
like a three and a four point bfk you have the two point bfks and climbing
so that's pretty much uh one of my favorite knots for highline anchors and
i actually incorporate it into some climbing stuff i do like the quad
anchor for big walls and you can see that in uh
another video i have so out of all out of all the knots we
just talked about what do you think is like
uh the most interesting or the most useful to you
i really like the tailless bfk probably just because of the fact that you can
incorporate like a personal anchor system just
directly into the master plan it's genius
my favorite stuff is i'm super disappointed in the unfinished
no wonder you can't really find that on the internet
probably shouldn't put it on there either but anyways i really like how
adjustable slings are because they feel so static like you can either straight
in line or put a basket or a girth itch and like
they're limiting but they're not and when you do the scorpion hitch you can
actually do one of those adjustable methods to
so there's so much that you can do with the span set and the purple ones are
light enough that i actually use them a lot in
highline rigging now because they're not too heavy
we're filming all of this on uh the new property that i live on
it's the welder who has made all my slack snap and bolt buster stuff and
that's where we have the slack lab if you like wine go grab some of his on
the website in the link below because this is his vineyard and he makes some
pretty dank wine appreciate your donations
everybody's really helped make this channel what it is we try to make the
edits better go to slackline.com if you want to see
the bolt busters uh the highline 102 course with the
class of notology that is also on slackline.com
give us your feedback on the google form on there lots and lots and lots and
lots of stuff on slackline.com what else
i don't know forget what else i'm supposed to plug
subscribe thanks hit that like button cheers