Replacing Glue In Climbing Bolts - Does a blow torch work?

HowNOT2
100 followers
1 Video View·Jun 11, 2022
Sometimes bolts get in the way of random swinging hammers. We explored two ways of heating up glue in bolts in an effort to remove them so you can reuse the hole. I'm not convinced this is a good idea. What do you think?
Don't try this if it is fire season. Don't try this without bringing a way to cut the bolt when you are done in case it doesn't work, because it has been compromised. Cutting and replacing the bolt right next to the old bolt is one solution as you can see here https://youtu.be/8pgFzVqVEJY
https://www.hownot2.com/boltingbible
💲💲💲Patrons get early access https://www.HowNOT2.com/donate 🙏🙏🙏
👉👉10% supports us at https://www.extremegear.org/
👉👉👉Shirts and hats http://www.hownot2.com/swag
Bobby, can you explain what you're doing? You're not that active in the daytime.
So we have this really cool rock here, which we'll get b-roll of later,
that we put bolts in. And we are going to use this cool map gas to heat up the head,
the goal being to melt the glue so this can be removed.
So we have left the back exposed so we can use an infrared thermometer to see how much
this heats up. What temperature is it now? It is about 60 degrees, which I would say
is the ambient temperature right now. It is because I'm not wearing my orange jacket yet.
Should I touch this side while you do it? Yeah, I think that would work.
I'm okay with it, not my fingers. I have infrared in my fingers.
Limestone is a pretty good insulator, I would say.
Oh Jesus, your red light! I thought fire was coming through the rock!
Yeah, you can cause more damage to the rock. It would start to look like California.
I don't have a rock near my house. I mean, you've heated it up 10 degrees.
In theory, if you did that for two hours, you'd get up to 150 degrees.
Now here's the thing too, is you leave the heat on all the time or you take it off for a while
and that heat will still kind of work its way in. Or you could do it on a 100 degree day
and start with some momentum. So show us what you're doing there, Steve.
So we've had it on for about five minutes or so, heating with a torch.
I would say closer to 10 or 12.
This has gotten up to like 600 degrees on the back side.
We're up to like 120. We're starting to give up. Then I just took the pry bar
and it is now at least spinning in the hole.
Oh man, yeah. I mean, if I came up to a glue-in that was doing anything like that,
I would be freaked out.
Yeah, so now once its bonds are broken, you can start spinning it.
Yeah.
And then be able, should be able then...
You can definitely use that spinning motion. Oh, there you go.
So keep in mind, this was only like an inch and a half or two of glue.
It would have definitely been a very close to a full strength
placement based on the testing that we've done.
240 degrees.
Let's move it off the carpet.
We're not holding the carpet. Sorry, Ryan.
This was done at the same exact time, same glue.
Let me get Steve struggling.
Yeah, put some force into that. See if you can get it to twist.
So this one was not heated up.
Were you able to do it?
The rock was starting to crack there.
Then I was worried about it blowing off in my face.
OK, so you got this side hotter.
Yeah, it got 115.
115, 120.
So if we did this on a hot day and you're starting with like a warmed up rock...
The back of the rock was reading up to like 170.
So the rock itself was getting hot too, so...
Yeah.
And I mean...
So the heat will travel.
In a real situation, you're dealing with a lot more rock, but...
You're still dealing with that first couple inches would be affected.
Yeah.
I just wouldn't want to compromise that rock
because that's what you're putting it back into.
Science.
So this is induction heating and that's heating up your staples.
Probably more than it is your stainless.
Stainless is floating in the 200 to 300 range.
Well, 250.
I mean, the bottom of the bolt's already up to 80.
Yeah, so you've heated it up 20 degrees.
And that's gone a lot faster than the torch.
Look at that name.
I like that name.
Yeah, if I could get a bolt to look like that, it'd be easy to remove.
Yeah, we're...
We need one of those stickers that say, may cause cancer.
That is good to see there.
92, yeah.
So the heat is going down.
Yeah.
You've only been at it for maybe double that amount of time.
But, you know, because you didn't...
You started that later.
Nice that the rock is not getting that same heat that the fire does.
Yeah.
Yeah, that is glowing red.
Interesting.
If you take a big bar, you risk breaking the weld, right?
Just warming, but I mean, it's just like...
It's not much.
400 degrees.
So can that heat transfer through over the next couple of minutes before it cools down?
So this is the next day after we burnt these.
This was the one that we used the map gas on, and this was the induction heating.
And we could not get this out.
We didn't go as long.
But the rock was not heated up.
And I think that had some effect because it's not just the heat of the metal, but the heat
of the rock.
But the induction heating doesn't burn the rock up quite like this does.
I don't know if that cleans up right now.
But I don't know if I'd want to leave that kind of scarring just so I could reuse the
hole.
Now, if we're trying to replace gluons, the whole point of this method is to reuse the
same hole so we don't turn our rocks into Swiss cheese.
But if we're causing all sorts of damage or spalling, then I don't know if that's worth
doing that.
So I think what we do on here is we weren't really careful.
We were hitting the flame going straight down, hitting the rock.
So you do a heat shield, like a fiberglass mat, like plumbers use.
You put that on there and then just really focus the flame on the bolt.
And just like that much around on the rock.
So you could try flame.
And then a bar that way in a vertical situation.
I don't think this is as useful.
10 minutes with a flame hanging while with a number set up.
Yeah, I mean, people weld on rope.
I mean, there's right.
We have buildings, but yeah, I just don't see this as a realistic thing.
And then you have fire risk, right?
If I mean, the whole country seems to be burning down, the whole world does.
I wouldn't want to do this unless it's like wet outside, right?
And then the induction, you need a power source.
I mean, yeah, you would need a generator and extension cord.
So that's very limiting.
This is mostly limiting.
There's a lot more cons and pros.
The whole reason we're discussing this is if bolts just accidentally get smashed
by hammers that walk by, they need to be replaced.
If people didn't do that, they'd probably be good for one or 200 years.
And by then, we'll be like on Mars and Jupiter.
And this would not be a problem.
It'd be very easy to solve.
When glue and bolts get smashed, basically, the best solution we have at this point is
to cut it off and put a hole right next to it and let the P shape or the bell shape,
in this case, cover up the other hole.
Because there's something in the other hole, that rod and the glue.
And if it's all glued in together, we did a whole video test where we did like
punched in a hole and then did another one.
And it came out in those tests just fine.
It definitely would mark it up.
Now, over time, it might not be such a big deal.
But I wouldn't want my crag or my highline stuff looking like this.
Back to the vertical scenario, I'm thinking in context of horizontal,
where top of a cliff, we have either anchors for climbing or anchors for highlining.
And this is usually where they're getting smashed, where they're conveniently
located for people to access, whereas this is just a lot more difficult.
And usually, people are using them when they're getting smashed in that case.
What's the conclusion?
Don't smash bolts.
Yeah, don't smash bolts because it's a pain to get them fixed up.
Yeah, if you don't like bolts in an area, well, cutting them off cleanly
and leaving less trace is the solution if you're going to be a dick.
Smashing them makes you an asshole.
So don't do that.
But this was a test we've been meaning to do for a while to see if we can solve some
problems we currently have.
I don't think this is the solution for that.
I think it was worth sharing in this video.
Sounds good.
Cheers.
