BOLTING BIBLE! Read it! It's free for bolts sake. There is a hole lot of good stuff in there! Have a contribution to make to it, message me. https://www.hownot2.com/boltingbible
Thank you Kieran Blood for helping with this episode and Nick McPherson for editing.
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break. This all couldn't happen without you!
Today we're going to cover the hole-ly part of the bolting bible,
and we're going to figure out how to make your holes right on this episode of Pound it to Highline.
Hi, I'm Ryan Jinks and welcome to my gear room.
Today we're going to talk about a hole-lot of good stuff.
I made some holes for us today so I can show you what's going on inside the hole.
I did it out of wood because rock's a little hard to cut in half,
but please don't start putting bolts in trees thinking that that's what this demonstration's
Let's first start with this example.
I did not drill my hole deep enough,
and so what happens is no matter how tight I make this now,
I'm going to have a spinning hanger.
And when you go up to a highline and you see a spinning hanger,
and you see it sticking up about that much higher than it should be,
it doesn't look like it was put in right.
You're questioned whether or not it's safe.
You want to feel good because this is all you're really connecting to
when you have a bolted highline.
The other problem is if it's pulling too high,
because if it gets lifted up and there's that gap underneath here,
then it can bend and warp.
It's like pulling on the top of a rebar versus like the bottom
if it was like staked in the ground.
It can lower the strength of the bolt significantly.
The reason this is important is if this was a glue-in,
you could test it first before you put the glue in
and pull it out and make it deeper if you wanted.
But when you put in, well, this is a removable,
if you put in any of those other bolts that are standard sleeve bolts,
once they go in, they don't exactly come out without like a bolt puller.
So it's important, unless you're putting in stuff you know you can pull out,
to make sure it's the right length.
Now what you can do is put a piece of duct tape on your drill bit
at the height you know it needs to be.
So as soon as the duct tape touches the rock,
you know it's deep enough
because you can always put this up against the drill bit
to measure to see the length.
Which brings us to this, speaking of length,
is you want to make sure it's a little bit deeper than what you need.
And it's perfectly fine to have it too deep on a mechanical bolt.
If you do it on a glue-in bolt, you're just wasting a ton of glue.
That's going to be expensive and it's pointless.
But on some mechanical bolts like sleeve bolts or wedge bolts,
if you drill them a little bit deeper than you even think,
if you wanted to unscrew this and pull the hanger off,
you can actually just pound it into the rock in the future
and eliminate the bolt if it'd be too hard to remove it later.
Put a little glue on top.
Not ideal.
It is important to reuse holes if you are retrobolting.
But either way, you have to have it deep enough regardless
because when you punch in, hammer in the stud,
the stud has to go down all the way.
And then when you start to tighten the nut,
it pulls it up tighter and tighter, spreading out the wedges in your bolt.
Another thing to watch out for is when you drill your hole,
that you make it straight.
I got my mechanical bolt here.
I'm all excited.
I lower the nut just below so I can hit the stud and not the nut damaging threads.
I'm getting ready to put it in.
And you realize after you stick it in that it's at an angle
because I wasn't holding my drill straight.
And what happens is even if I make this tight,
I can keep the hanger from spinning or moving,
but it can significantly reduce the strength of your bolt.
Yank on your hanger weird.
Your bolts have to be straight.
Your bolt holes have to be straight when you install them
in order to have a quality bolt installation.
Now, either with the P-shape or the bell-shaped glue-ins,
you have to create a notch in order for them to sit in for two reasons.
This one, it's nice when you can vary the weld.
It protects it from weather longer and it adds strength to it.
Now, this weld is actually pretty high up
and you don't want to like bury this halfway into the rock
or you won't be able to fit as many things in there.
But in this case, I like how I notched this one out
because there's just a little bit of metal protruding up
from the flush part of the rock in order for the rope to be touching that
instead of grinding on the rock when it's in here.
I don't want it to be rubbing on crystals or on rock.
I want it to be on this smooth metal.
The sacrifice I get with that is the weld is not entirely buried,
but I'm not concerned about that because the way I install these,
I put them in backwards.
So in this case, the rope would be being pulled this way.
Now, some people are concerned by putting in the glue-in bolts backwards
that this P-shape is being bent backwards in an unfavorable way
and it's not designed for that.
However, you're pulling on this directly on the spine,
whereas here you're pulling directly on the spine.
And now if I were to add a P right here on top of this and pull this way,
I don't believe it's going to reduce the strength of the orientation
that I'm pulling it now, which is this direction.
Now, the reason I like to put these in backwards
is you can put your static rope, 10 meter long anchor rope through here
and pull in any direction up to 179 degrees
in order to rig multiple highlines from the same anchor.
If you were to go more than 179 degrees, it would flip over to this side
because there is a concern if you were to pull this sideways
that it would twist and when something twists,
it would crack the glue and basically come out.
However, the notch does prevent a lot of the twisting that could happen
being that you can't really twist this even in my wood sample right here.
So this is not tight at all, but it is notched in a wood sample.
So Kieran is going to try to twist it out of the rock.
There's no movie magic here, folks.
A notch does prevent a lot of twist action that could possibly happen,
especially if it's glued right there.
So glue-ins are the biggest limiting factor in a glue-in
is the fact that you can't pull it in more than one direction
and that it should really be straight when you attach your directional force on there.
However, if you put it backwards, you don't have to worry about it.
And if it's off slightly a little, it probably still isn't a problem if it's properly notched.
And again, back to depth is this is just slightly deeper than I need it.
However, if you're measuring based on that depth as you're putting it in
and you forget that you still have to notch it,
that you do have to drill it a little bit further than you think.
You have to take into account that it'll be in that much deeper.
Notches take up quite a bit of glue and space and needs to be accounted for.
Now, this notch is actually kind of bad, just the way kind of the wood drilled out.
You can see how much bigger it is than it needs to be.
And it's nice when you use the same size drill bit, which I did.
The rock generally is only just a little bit wider than the metal shaft itself.
Now, what happens if you drill your notch too deep?
What you can do is you can just take a pebble, not dust, but a pebble and place it in there
just so it doesn't sink in the glue and it sits on top.
Or you can put a little rock in the bottom until it sits there
just the way you want before you add glue.
And then once it's the way you like it, add your glue as long as that little rock didn't move
and it'll stay in place until that glue hardens.
Once the glue hardens, you'll be fine.
And lastly, whenever I bring up drilling holes for bolting,
I want to emphasize, especially for glue-ins, that you clean the hole.
You can't just blow out the dust.
You can't just brush out the dust.
You got to blow, brush, blow, brush, blow, brush to make sure that hole is clean.
Because if the glue is only bonded to the dust, it could come out significantly,
significantly lower than if it was bonded to the rock, which is what it's designed for.
Blow, brush, blow, brush, blow, brush.
And the last point that I'm bringing up, which is I feel the most important point,
is you can't change a hole.
You can change a bolt if it's like, oh, it was a zinc-plated bolt,
or 20 years has passed, you can pull it out, put something else in.
But you can't change the hole.
Once you drill a hole in a rock, it's there forever.
Whether or not you change the bolt.
Yeah, you can always fill it up with glue, but like, it still was a hole.
And you know, 100 years from now, if people have been doing this every 20 years,
everything will look like Swiss cheese.
And you really need to think about, really, really think about
where your holes need to be before you drill them.
And only put in what you need.
Harder rock may not need as many bolts.
So really, really think twice, test it, check it, consider it, and drill sparingly.
I'm all about L&T and leave no trace, and I'm all about safety.
So let's find a happy balance when we're installing bolts for highlines.
Now sometimes, if you did this wrong enough, you could die.
Or kill somebody else.
Therefore, you shouldn't bolt highlines.
Hey, thanks for watching.
But don't be an idiot and get the same satisfaction from bolting
as graffiti artists do from tagging a wall.
Just because you establish a highline, doesn't mean you're awesome.
You really have to make sure it's worth establishing,
drill sparingly, and kind of gotta know what you're doing.
So please read our entire bolting bible, which is on slackademics.com.
We have lots of resources.
You can message me personally.
I know people who know more than me that I can put you in touch with.
Thank you to my patrons who help support this channel.
We do a lot of experiments.
We're actually building Bolt Busters, the sister of Slack Snap.
And we're going to break hundreds and hundreds of bolts.
Just because it looks like fun.
And the people who do get involved get to see our entire data
for Slack Snap and eventually Bolt Busters and the videos correlated with it.
Because I technically only publish about 20-30% of the results that we get.
Until you have a chance to not put in holes where they're not needed,
please like, follow, and subscribe.
And please hit that bell button so you can make sure you catch
all our future episodes where we go into details about more bolting.
Cheers.