If bolts are damaged or there are mistakes or in order to leave less trace, it can be nice to bury an old hole under the P of a new glue in you are installing. We tested in this video if "too much epoxy" was bad. The recommendation is just to use only a small amount. It is better to use the right size hole as it saves a ton of glue but we wanted to know if it was super good enough if you didn't.
Spoiler Alert: Our tests showed it was fine. All tests were done with Liquid Roc 500 Fixe Hely Tension (3/8" bolt in a 5/8" hole) 29.86kn, 30.30kn, 28.10kn - all bolts snapped Fixe hely Shear (3/8" bolt in a 5/8" hole) 31.68kn, 30.36kn, 33.82kn - all bolts snapped Double holes with 10mm Solid Leg from Bolt Products 52.38kn, 47.50kn, 50.86kn For reference, carabiners break around 22kn.
Is too much of a good thing bad? Most cases yes. We have oversized the holes for our glue-in bolts
and we're going to find out if too much epoxy is bad for our climbing bolts. Stay tuned.
Hi I'm Ryan Jinks and welcome to the Middle of Nowhere where we are testing
bolts and in this episode we are going to talk about too much glue, specifically epoxy. If you
guys want to see vinyl ester that'll have to be a separate episode. When I was learning how to
glue in I was told that too much was a bad thing and that the epoxy is very much like plastic and
it was brittle and crack and the bolt will come out. You typically want to drill the hole for the
bolt that you're doing close to the size of the bolt. In this case this is a 10 millimeter solid
leg bolt from BoltProducts.com and you can use a 12 millimeter or a half inch 12.7 millimeter
hole for this. That's not too much glue. This is a Healey fix and this is great for 3.8 holes.
Now you technically don't want to go bigger because that's just going to suck up a lot more
glue but sometimes there are situations you are either stuck using a bigger hole or you don't have
any more of the small drill bits. It's never happened to us. It also could be because of a
trick we're going to show you later on fixing mistakes. So there are plenty of reasons that
shouldn't exist why this will happen so we're going to find out if it's dangerous. So here we
are going to test and shear our fix Healey bolt and you can see that it is a lot of space around
the bolt and this is the skinniest glue-in bolt we have for the biggest 5.8 inch bit we have.
So this is a great test that we're going to do. So this is the hydraulic we have that we're going
to be pulling on that bolt. We have this to keep the hydraulic from flying when the bolt comes out.
Here we have that side anchored to that rock so we can pull and snap things and our dynamometer.
We are going to turn this around and pull bolts in tension or straight out. Come over here I'll
show you what I got. So here in tension we are going to also pull the fix Healey bolts. We're
going to kind of lift this up with a little pebble to make sure it's centered and then
pull straight out. These bolts up here are for another episode so be sure to subscribe to see
that. And these are Simpsons strong tie Titan HD concrete screws which is our workhorse for
temporary anchors to hold our hydraulic. Hi I'm Bobby. We're going to talk about a method to
fix mistakes when you are replacing bolts. It doesn't always go well when you're removing bolts.
Sometimes things break. You can't totally reuse the same hole. So I'm going to show you a little
trick and then we're going to test it. If it doesn't test well, ignore this trick. What's this
device Bobby? So this is yet another bolt remover. These are machined by a climber specifically for
this purpose of removing bolts. So sometimes you can't get the whole bolt out of the hole.
Could be a lot of reasons for that. Too rusty to come out. Part of it came out and there's still
some left in the hole. So in an effort to leave less trace, we don't want to just drill another
hole in another location. We want to try to to keep it all together. So I'm going to snap this
bolt and then we'll show you a trick for doing that. That's scary. Oh snap! Literally. So there is
a bolt still in there. That's the part that came out. You can see the the metal has elongated a bit
before it snapped and it snapped at the weakest part of the bolt right before the cone expands.
So the cone is down there and you would either have to drill it out or do this new little trick.
Or do this new little trick. Okay. So one method would be to just take your rotary hammer drill
and a bit you don't like and just drill until you've just removed all the metal and that's going
to take a while. It's going to heat your bit up really hot and there's no guarantee that you go
all the way through. It'll eat up batteries. What's the drill bit? Which one do you use? Since I have
them with me, I just use a masonry bit. An SDS bit with a carbide tip. A masonry bit will drill through
the cone? Yeah. I mean it takes a while. Okay. That carbide is really hard. I don't think you could
use a metal cutting bit because as soon as you touch the rock, I think it's going to destroy it.
So I learned this trick surfing the forums on Mountain Project. Spent a lot of time doing that.
A lot of good resources there. And where else is this trick now written? I think it's in the
Bolting Bible. You should go check that out. What's the trick Bobby? So what we're going to do is take
our rotary hammer drill and drill right next to this hole. We are going to try to avoid hitting
the existing hole and the metal that's in there. But as close as we can. And then we will
fill it with glue and put the bolt on top. Our glue in bolt right on top of that. And hide it.
Okay. So we can see the bolt next to this new hole. Now some bolts you can notch. Sometimes
you can notch this. Which means you can drill here and over. So it actually sits a little bit
lower than the rock. Leaving this part still exposed. So the rope is not rubbing the rock.
But either way that hole is still covered by this. And it doesn't look like you've just whisked
cheese the rock. Leaving less trace. Here at Bolt Busters we like to do three of whatever we do. So
Bobby is now going to snap another bolt. Drill another hole. And then we will glue all this.
And then we have a third hole over here that we're leaving empty. We'll probably put something in
there so the glue doesn't fill that up. And that's to simulate say there was a rusty bolt in
there. And it totally rusted. Worst case scenario. And it's just dust in that hole after 200 years.
Nice. Able to finish this one nicely. You can see the bolt in there. It's just touching.
This one did not do so well. It got too close and drifted into that hole. And then was binding
like crazy. I ended up being able to pull the sleeve out. But the bottom of the bolt is still
down there. And this bit was just binding, binding, binding, binding. You can see it got really hot.
So we decided to drill another hole behind it. Because we're still able to camouflage that
original hole with this placement. And what's Wilson doing over here? This is to simulate
in a long time the remaining rusty bolt just totally disintegrating. There being nothing
structural in there. We don't want it. We don't want this to fill up with glue. And then we'll
cover that non-filled hole like that. So we're gonna have this full, full, full of epoxy. This
has half epoxy, half bolt. And this has only epoxy in the hole for the bolt. What do you think's
gonna happen? Based on some testing done by our friend Jim Titt over in Germany, they will break
full strength. So we're using Liquid Rock 500 here. I squirted some out into a Mickey Mouse to make
sure that this is going to harden. If this hardens, that hardened. Let's pull out our next one. And
the idea is to get this everywhere. Everywhere inside of the hole. You don't want air bubbles.
Twist when you enter. This is so much movement. We'll just use some pine needles. This is going
to be my lifter upper. And if anybody comments that that's going to compromise our test,
then it'll help the algorithm. Not my finest work, but it's coming out tomorrow.
I'm sinking. Wow, you can like tilt this thing. Welcome to tomorrow. It's been about 16 hours
and it was pretty nice yesterday. So we feel these are fully cured enough. We can make a
t-shirt that says that. And that is ready to be pulled. So let's do it. All right, so look at the
glue here. I mean it crushes it. I mean you're pulling 31 kilonewtons against it. That's what
I would kind of expect, but it didn't compromise the strength. So this is one of the strongest
results we've gotten with these Healy bolts. There's a bolt in there and that's pretty
consistent results. We did blow this one out and yes, it pushes against the epoxy, but it still
holds. That's good to know. Let's pull this one. All right, so that glue I could hear crunching.
Let's see if we can see the bolt here. Oh, it moves it all right. That sure is interesting,
but we are getting some pretty decent results. All right, so we can see here this happens every
time you have excess on the top, which is why we thought too much would be a bad thing.
But you can see there's a lot of glue still doing its thing in there. That looks pretty normal
and that's a pretty high result. What do you think Bobby?
I am pretty impressed with this method at 50.86. This was the hole, screwed up hole, third hole.
I'm so happy right now. Hey look, the Dean Potter. Whoa, huge result difference. Just kidding.
Well, there are some consistent results for you. This is more consistent than my ex-girlfriend.
Which ex-girlfriend are you talking about? All jokes aside, that keep me single,
we did not notice any difference in epoxy if you use too much. We don't know if this will happen
the same with vinyl luster, AC100 glue, or crappy polyester glue, which you should not use. We
basically really tried to screw this up and we couldn't. I am pretty excited about the results
where we have the other old hole underneath the eye of the next glue-in bolt because we may or
may not have done that in the past. Sure nice to know it worked. I do like the idea of leaving less
trace and being able to hide one inside the other is nice for that. Put in the comments below if you
think that's still sketchy even though we just showed you it's not and tell us if you want to
see us do this in polyester or vinyl luster because that was a lot of work for basically nothing.
Thanks for watching. If you made it to the end, you win a free subscription to this channel.
Hit the subscribe button. Cheers!