Salvaged R34 Skyline almost Fully RESTORED | Poor Man's GTR [EP14]

Broken Silvia
74 followers
5 Video Views·Jan 1, 2020
In this Episode we continue rebuilding the R34 Skyline by getting all the suspension parts freshly powder coated and new Nismo bushings pressed in. After many months the car is finally a rolling shell! The next Episode will be a big one to say the least, and then we move onto playing with engines..
Song @3:08 by Saiki Beats (Utopia)
https://www.youtube.com/watch?v=4dlYuSl_b84
_________________________________________
My Instagram: @broken.silvia
Contact: [email protected]
Produced by: Damjan Bradonjicm
Hey everyone my name is Damian and welcome back for another episode
as we continue rebuilding this R34 Skyline. So the car
is actually rolling on its own wheels which is
amazing because the last time i've seen this was many many
many months ago where we pulled the subframes out of the car to put it onto
the rotisserie and ever since then the car's been onto
rotisseries and dollies but never on its own wheels even though
they were stolen off the Silvia but regardless in this episode we've got a
push the car over over the lift brush on the last
layer of the underbody protection pressing some new bushings into the
freshly powder coated subframes so yeah we've got a bit of work ahead
so we might as well get started. So before we get to the fun parts of
putting freshly restored parts back onto the Skyline
we've got to do the dirty jobs first which includes removing all the
bushings bearings and ball joints out of the
suspension parts. Now i'm not going to show you on how i did this because my
methods are are quite sketchy to say the least and
i'm sure there are videos out there explaining this better than i ever would
so we're just gonna skip that topic in general but anyways the point of this is
all these parts are now free of any old bearings bushings and ball joints and
it's time to send them off to the powder coaters
so in my case it wasn't even worth trying to sand these parts back and
paint them myself the powder coaters did an amazing job
so what they do is they sandblast all the parts back to bare metal
and zinc primer them and then they powder coat them in your desired color
i chose satin black so the next job on the list before
pressing the new bushings in is to grab a dremel with some 80 grit sandpaper and
just clean up those surfaces anywhere where you are planning on
installing a ball joint or bushing so what this is going to do is
ensure that there's no paint or powder coating build up in those sections
because the bushings are really really tight fit as it is because they've got a
metal casing if you were using just polyurethane
bushings with no metal casing around it they would slide right in
but because we're using factory bushings or if you're using solid bushings
you probably want to clean up all these surfaces and even use a bit of grease
before pressing it in alrighty so now let's answer the
question of what bushings were actually used on the underside of the car
and why i chose nismo over polyurethane or solid bushings
if you're just here for a bit of music and entertainment pretty much maybe
skip to a minute whatever it says on the screen
but if you want to geek out into restorations and talking about bushings
i guess we'll talk about it for a minute so pretty much backstory is this
car came out of the factory 20 years ago
and it's done about 120 130 000 kilometers i believe
and the suspension parts and bushings are obviously going to wear down
over time and they need replacing and the whole point of this build is for it
to be a full restoration but still be a street car now i know
that there are many definitions of what a true street car is
but in my opinion as long as it's nice and comfortable it's not whining
that for me ticks all the boxes so the nismo bushings were the way to go
i've been in cars with polyurethane subframe bushings
and solid subframe bushings and i'll tell you right now that that is not for
me the diff or any road noise will come
straight through the subframe and into the body of the car
and as loud you can play your music as loud as you want to have the best sound
system but that whining noise is always going
to be there which for me is a big no-no so yeah nismo
is harder rubber it's brand new than what was once in the car
so that's also a huge bonus and to be honest
being a street car you're never actually going to push it to the limits
where you need polyurethane or you need solid bushings so in my opinion
if you're building a car specific specifically for the street
to enjoy it probably stick to something on the lines of
oem bushings so while preston was using the dremel to clean up all the
suspension parts i decided to jump on to another job
which is the boot and just quickly brush on some gloss black enamel
just to clean it up and finish it off
so by the time we were done with all the rear suspension it was
pretty much midnight and we we decided to call it a day
so before putting the subframe and the fuel tank back into the car the brake
lines and the fuel lines have to be installed first and i
absolutely hate the look of those plastic ones and they always crack so i
decided to just put a rivnut into the body of the car
and use some p clamps to hold those lines in place
so remember the order that everything has to go back on so the fuel and the
brake lines go on first then the fuel tank then the heat shield
then finally the subframe can be bolted in place i had to do this job
two or three times in the silvia because i kept stuffing up the order
so this time i made sure to get it first shot and yeah it's a pretty good feeling
so again i'm going to spend the next minute or so geeking out into the
suspension of the car if you're here for entertainment skip to minute
whatever it is but yeah we'll talk about the rear subframe the fuel lines and the
front suspension so starting with the back of the car
the rear subframe all the arms that are bolted to it so we've got
standard control arms with new bushings in it we've got
aftermarket camber arms which are made by cusco or cusco however you may call
it they came on the car they're in good
condition so i just ended up reusing them and the car also came with cusco
hikers delete the four-wheel steering thing but unfortunately i didn't really
like the setup of this arm because it uses a ball joint that goes to the
knuckle and anthony from dartan racing actually recommended me a better
alternative where instead of using the ball joint it just uses a normal knuckle
bushing which is sweet it's probably a bit more safe as well so i just ended up
buying that kit and then that tiny little arm i don't know what it's called
but we just ended up using the factory one that was already in the car
if we ever need more adjustability i'll just buy that third arm so it's also
adjustable but i don't think we're going to need it
so i would have loved to put driftworks or hard race or
any other brand of arms under this car that's like hardened rubber and not the
spherical bearing ones but unfortunately with the time
constraint it just was not in budget so we just used what we had
and i'm sure it'll definitely do the job then we've got the fuel lines the fuel
lines actually already came on the car this car was pushing i think 450 500
horsepower and ethanol before so i just ended up reusing the lines i
just cleaned them out and put them back on the car and lastly
the front suspension as you can see it's all kind of crusty
and that actually came off my friend dan's car now
some of my parts didn't get powder coated in time and i'm missing a few
bushings to get my parts put back on to the car and
rolling so i ended up pinching the whole front subframe assembly from his car
and put it into my car so that's probably why you're thinking why is the
front end old and the rest of the car is nice and
fresh so yeah so we're almost at the end of
another episode and as you can see the car is rolling on its own wheels
and for the people that have stuck around till the end the car actually has
its own engine so i didn't really need to get this
car rolling right now i could have still done all the jobs i had planned on the
lift like putting the engine back in starting the fabrication
no worries but the reason why i got this car rolling sooner than later is because
of the next episode the next episode i need a few shots for
with the gimbal and the camera and stuff is going to be the biggest episode and
the biggest video i've ever made and i can already feel myself having
a meltdown editing the thing and i can already see my computer probably
catching fire but you know what it's going to be totally worth it it's going
to be the biggest video i've ever made and i'm going to try and get it right so
bear with me another one or two weeks worth of editing
and then it's going live now before that video goes live i'm going to post a two
minute video asking you guys for a favor then one or two days after that video
goes live we're posting the biggest video i have
ever made now i'd like to give i would like to say
happy new year to everyone it's the 31st of december
right now and i'd like to say thank you to my friend preston i know we've had a
fair few late nights here working on both cars
so thank you for all your help thank you for
everybody liking the videos leaving some support
some feedback and hopefully 2020 will be
will be an exciting one so catch is later
