In this Episode of the Supra restoration I showcase the car receiving its final stage of primer. It is a lengthy video that is concentrated on the blocking process and blocking tools used on the car along with a comparison of different brands such as 3M, Durablocks, Linear blocking tools, Melomotive splines and others as such.
The car is officially paint ready! I also reveal the plan of attack that will take place towards completing this car along with the engine that will be used.
Video Breakdown: 00:00 - Content to Expect 00:54 - Introduction 01:51 - What Happened Previously 02:45 - High Build Primer / Checking Panels & Blocking 06:32 - Sanding Block Comparison (Most Popular) 16:36 - Outro / Engine Reveal / Plan / New YouTube Channel
Ah ----, here we go again.
And welcome back to the final episode of the Supra paint preparation.
Today's episode is going to be nice and simple.
I think this whole Supra series has been concentrated on bodywork.
This is the final episode of bodywork before we go into paint.
And today's episode is going to be about some basic tools.
So we've got about $2,000 worth of sanding blocks.
I've tried them all out and they all serve a different purpose.
I'm going to recommend which ones are my favourite.
And I'm also going to recommend which one might be the most appealing to the DIY guys.
And I think this whole series, even though we've skimmed right through it,
I think all the information is there that if you follow it step by step,
you take your time and with some basic tools, even at home,
doing it for the first time, you can achieve some great results.
If you take your time with it.
So let's get into this episode and have a look at what happened previously.
I'm going to die.
Previously on the Supra rebuild,
I showed you guys the process of preparing the bare metal for epoxy primer.
Then the car received two to three coats of epoxy primer
that is used as the foundation to seal up the bare metal from rusting.
After that, it was skimmed and the blocking process begun.
Now this takes a long time to do,
but this is a very crucial step in making sure that this car is going to look nice and straight.
Once the car was blocked, there were a few little sections that were bare metal.
So to make sure that we don't have any problems in the future,
I applied another two light coats of epoxy primer,
which I then blocked with 240 grit sandpaper.
Now at this stage, the car was pretty much paint ready,
but we also want to apply a high build primer
just to make sure that this car is mega, mega straight
and also our waterborne base coat sticks and adheres nicely to that high build primer.
As mentioned previously, the epoxy primer has a thin build
and is used to seal up the bare metal from moisture going through and oxidizing the metal underneath.
The high build primer, on the other hand, has no real moisture barrier,
but is used as the thicker build.
I sprayed three relatively thick coats of the Chromax 1057
with a 1010 hardener, thinned out approximately 20%.
This is the darker shade of primer, which I used for two reasons.
First reason is I'm painting a darker color
and the darker ground coat should help with coverage
and should also give it a nice, deep, dark look.
The second reason is while I'm blocking the car,
I can use wax and grease remover from the pump spray to check how straight the panel is.
As darker colors also show the imperfections,
once I spray the wax and grease remover,
it almost acts as like a bit of a clear coat
for a short amount of time before the chemical evaporates.
Now during that period, I can take my time outside
and really check this panel to make sure that it is nice and straight.
So once the three coats were bombed on,
I used a trick that Colton from Linear Blocking Tools mentioned.
Instead of using a guard coat, what he does is
he uses a small amount of base coat that is the opposite color of his primer
in the leftover pot and dusts it over the whole car.
This is honestly genius.
Once the primer has settled for a couple of days,
I begin slowly blocking the whole car
and we're going to talk more about it in a moment.
In the past, what I would do is use 240 grit sandpaper to block the car
and once that was completed, I would refine the scratches
with 500 grit on a dual action sander with a foam interface pad.
Now I would pretty much paint the car right after this step.
So since I was told to stay away from the DA sanders,
so I continued to follow the instruction provided by Colton
and the whole car was blocked with 240, 320 and finally 500 grit
using the 3M stick-on paper and the Linear Blocking Tool.
Between grits, I reapplied a powder form of the guide coat
that helps me spot potential defects missed.
Honestly, by now, you really shouldn't have any problems or any defects
and the main purpose of the guide coat should be used to show you
the previous scratch or sanding marks that were left behind
that you need to block.
Once you finish with the 500,
you are now ready to apply your base coat and clear coat.
Alright boys, so I'm a fair distance away from the camera now,
hopefully the audio is still going to be okay
and now I'm going to be comparing all the sanding blocks I have
and I think these are the main ones that are out there on the market.
As I said, I've spent about $2,000 acquiring all these blocks,
playing around with them and I finally,
I think I've got enough of an understanding
to give you guys a bit of a glimpse in what I would personally use
and what I would recommend for different situations.
So, we've got everything from the Millimotive splines
to Velcro paper, stick paper, dual action sanders,
the legendary Linear Blocking Tools,
Dura-Blocks that everybody's heard of
and your basic 3M stick-on paper sanding blocks
that are mainly seen in the collision industry.
So, we'll start off with the palm sander.
This is a very commonly used tool, very inexpensive
if you're just going to buy a cheapie like I did.
I don't use it very often for multiple reasons.
So, it's got a foam pad which is soft, it spins,
it's not very nice to get those nice flat finishes
so I don't use it but however,
the time I did use it is to strip the cars back to bare metal
and as the final stage before paintwork.
What I mean by that is I'll do the final prime,
I'll block the panel using 240 grit sandpaper on a block by hand
and then I'll put a foam interface pad on the machine
and 500 grit dry sanding paper.
I would guide coat the 240 grit marks
and refine them with the 500 grit.
And overall, I'm pretty sure every car that I've done so far
has been done like that.
They all did turn out pretty nice.
However, I think we can do an even better job
using some nicer blocks and doing everything start to finish by hand
as Colton has recommended me to do.
So, Colton is the guy that produces these sanding blocks
that's really opened my eyes to the world of body work
and how to do it properly.
So yeah, the palm sander, probably not an ideal tool.
Moving over to the 3M blocks
or these are the 3M style blocks.
Again, very cheap.
I think I paid about $100 for this one, this one
and the third one is at home
but it is literally this exact size
which is a really nice size to have
and it's usable on most cars.
These blocks are mostly seen in the collision repair industry
because they stick on paper.
It's nice to be able to flick between 80, 120, 180 and so on grits
and be able to reuse this paper
because once you pull it off, the Velcro still stays good
and it's reusable compared to the stick-on paper.
Once you stick it on and you take it off,
it is good to go in the rubbish.
Now, the biggest downfall of these blocks
is that they have a foam interface pad
and then they have the Velcro
plus the Velcro on the sandpaper also has a bit of a cushion to it
so when you take all three things into consideration
you end up with a very soft block
that can dip into ripples and small little defects
meaning that you aren't going to get an overall perfectly flat finish
if that's what you're looking for.
But it is a good block, as I said.
I think I paid about $100 for the three
and I did the whole R34 GTT with these blocks
and the DA sander
because it was just a quick little tidy up
that I wanted to make nice
and a car that I'm going to be selling in the future.
Awesome little street car
but unfortunately for the type of work I want to be concentrating on
these aren't the blocks for you.
Moving on, DuraBlocks.
Everybody has heard of DuraBlocks
if you've googled anything to do with bodywork.
They're a very cheap block.
I think the kit of seven I paid about $150 AUD
and they come with different sizes
round, flat, blah, blah, blah.
They come either using stick paper or Velcro paper.
I would personally get the stick paper
at least you're going to get a little bit of a nicer flat finish.
Again, it's not a perfect block
but it is better than the 3M style ones.
So they're a bit of a foam block.
Once you start pushing their limits
they don't contour a nice
they don't have a nice perfectly flat round
such as the linear blocking tools.
For example, they kink.
But I've seen great results come out of these blocks.
I want to give a massive shout out to Paul Roseboom.
He uses these blocks on all his projects
and the finishes he achieves are absolutely 10 out of 10.
Guy that has also guided me through this whole rebuild.
Very much appreciate your help.
I'm going to link his YouTube channel in the description below
if you just love Supras
or really have an interest for any form of bodywork or restoration
because he goes into a lot more detail than I do.
The episodes are lengthy
but definitely worth checking out.
I don't want to be another one
Paying for the things I never done
Don't let go, don't let go of my love
Alright, going back on track
we have the melamotive polycarbonate blocks.
I'm pretty sure these are polycarbonate.
I paid $300 for a set of 9.
At start I said, you know what, I finally found a block that works.
$300 for 9 of them that come in 9 different sizes isn't too horrible.
But, unfortunately, once I started using them
there are limitations to this block
and I've stopped using it since.
They've got hard edges, hard corners that you can dig into.
They don't have any handles
so what you end up doing is
you end up putting sandpaper on both sides.
You use one side as you're sanding
and you use the other side as a grip.
Now you can have 80 and 120 if you're doing your filler work
so then you can just flip between the sides
and both sides act like a grip on your fingers.
Again, a block that is good
especially considering the price
but personally I would stay away from the melamotive blocks as well
as they are a little bit tricky to use.
These are called the melamotive splines.
But, if nothing else existed
these are the tools I would be using
because they are perfectly flat.
Moving on to these tools
the best on the market currently
and that's why they have a very hefty price tag
of $1100 for 15 blocks.
I bought the master set. You can buy them individually.
I only used probably 3 to 5 different blocks
to complete the whole Supra
which is a relatively curvy car.
If you're working on a more simple car
like a Skyline for example
I really think that you could get away with
using only 2 or 3 different style of blocks that they offer.
And these blocks come in 3 different styles.
So you have the rigid.
So they're all, between all sizes
from the small ones to the big ones
they all use the same thickness of backing plate.
They use stick on paper.
All the edges are nice and CNC routed.
You're not going to be digging into your panels or anything like that.
And what determines whether this block flexes or not
is the actual handle.
How nice is it having a handle?
So this is obviously the rigid block.
It has no grooves. It's got no flex.
And a block that I pretty much did not use
once on any of the Supra parts.
Then we have the tool that is most commonly used
I would say on 90% of cars
and it's the flex block.
It's nice, perfectly straight.
It's got enough flex to do bonnets, roofs, quarter panels, doors
you name it, you can use it.
It's perfectly flat.
Uses stick on paper.
It's honestly, in my opinion, the ideal tool.
It's very, very nice to use.
I'm not getting paid to say any of this.
I paid $1100 for this ----.
But yeah, Colton, if you're watching it
and you want to send some more blocks out
with some mud pallets or whatever that you have
for a bit of a review, feel free to do it.
I will, however, mention a limitation of these blocks as well.
And finally, we have the ultra flex block.
Again, not a block that you will often use on most cars
but when you need it, you need it.
I did use, I think, one ultra flex block on the Supra
because the Supra is a curvy bitch.
So the limitations of these blocks, really
the only limiting factor is for us in Australia.
Worldwide, you can order these blocks individually.
In my opinion, massive **** up that we can only get them as sets
which is a bit discouraging for the DIY guys
because they really did create the ultimate sanding block
and to be able to just, you know, go to your car
and have a look at it and be like, alright,
this section here, we can use a flex block
and roughly measure up what size block you think would be nice
to block that panel, make a bit of a list around the whole car
and decide we're going to order three or four individual blocks
and that's enough to do my whole car.
You save a lot of money from a professional doing it
and you get great satisfaction of doing it yourself.
Now, the thing with us in Australia is
something to do with distributors,
you can't directly order off their website
and have it sent to Australia.
So when I bought these, I had to buy them as a kit.
Obviously, I would have bought the kit anyways, the master set
but they also have the labour saver at about five or six hundred bucks
which is a little bit expensive for the DIY guys
that might only need three or four different blocks.
So if that's something they could change,
I think that it would be good for their business
and also the people that are using the tools,
they'd sell a hell of a lot more.
So when I ordered the round set,
I ended up going through my friend Gabe in America, in Miami.
Massive shout out Gabe, you ******* legend.
He sent it via the Titanic.
Took two months to get here
but we finally got these sanding blocks
and this is the round set.
So same principle, a nice perfectly flat block
but it's used on round sections
that you can't really get a block like this into.
Alright, so we're approaching the end of another episode.
We covered the high build primer,
we compared all the sanding blocks
and in the next video I'm going to restore the underside,
tell you guys how I did it
and we might even throw some footage in of me painting the engine bay
because today is Saturday.
You guys will probably see the video on Monday,
my bad, on Sunday
and then on Monday I'm going to go pick up the paint for the car,
for the exterior.
We're going to paint the engine bay,
we're going to make it a rolling shell
and then we can push it into the paint booth
and paint the complete outside of the car.
Now as you guys can see, the 34 is also on the trailer.
I'm going to put it in storage.
It's just sort of taken up space
and I'm grinding, cutting, welding, sanding
so it's just sort of getting neglected
so it's better off just sitting in storage.
This is the first time that the car hasn't stressed me out.
Usually I just want it on the road
but really I think what I'm doing now
with these other projects that are going on,
if we have a look at Dale's R32 GDR,
this is a customer's car,
I think we're sort of on the right track
to the point where I keep seeing new products come out
that I'm really interested in
so it'd be good to see someone else in Australia
be the dummy to make it all work
before I commit and buy these things
because as we know, when you're the first one doing it,
it usually ends up costing you more than it should.
So yeah, as I said,
first time that the 34 has not stressed me out one bit
and I think in about 12 months
when we're ready to get stuck into the car,
we're just going to have all the parts laid out
and it's good to be assembled.
Now for the Supra,
what's happening with the drivetrain,
we might have sort of stepped away from the Barra idea.
It was going to be a little bit too expensive
to get inside the car to make it all work
because it's a very tall engine
and the way that the crossmember is set up in the Supra
isn't ideal.
Pretty much the only engine that was ever supposed to go into that car
was the 2JZ.
So I'm going to end up pulling the bottom end out of this
which is a GE bottom end
and I've already ordered a brand new VVTi GTE cylinder head 2JZ
that's going to go on top.
The turbo kit's already been ordered.
The intake manifold I have.
The gearbox adapter's been ordered
and I'm just going to borrow my mate's TR6060
for the time being to put everything in the car,
have all the intercooler pipes fabricated,
the exhaust and then everything can come out again
and we can play with the engine on the stand,
give it a bit of a refresh
and then it goes into the car for the final time.
We do the wiring, the reassembly, engineering
and the car is now street legal and ready to be driven.
Obviously it sounds a lot easier than it is
but I think that's sort of the plan of attack for that car.
Concentrate on one project at a time
and then you're thinking
well what's going to happen with this Supra then
when it's got no engine?
As you know my friend Tristan over at WTF Auto or Quick Shift TV
he's doing a V12 swap on his Supra.
He's getting really close to the point where
everything has been prototyped, everything fits
and he can now start reproducing this as a kit.
So we'll see if we can maybe team up on this
and see what sort of deal he can do me
in return for some exposure and stuff like that.
So instead of having two 2JZ powered cars
I think it would be ******* awesome to have a V12 twin turbo Supra.
Yeah, I think we sort of went off topic
but that'll do for this video.
This is the first take and I've actually succeeded.
Danny's not hating life holding the camera.
We'll see you boys next week
and we're just going to get episodes rolling out.
Oh, one more thing before I go.
For the people that live in the Balkan region
so Serbia, Montenegro, Bosnia, Croatia, Macedonia
obviously I'm bilingual.
I lived over there, I lived here
and yeah, I've started another YouTube channel speaking Serbian
retelling the whole story of everything we have done so far
in a different language for a different group of people
that unfortunately never really got these cars
never got to see these cars but have a massive passion like I do.
So I think it's pretty cool for me to share my experience
in a language that they understand
and if you are from that part of the world
there's a link in the description below of the YouTube channel.
Go check it out and subscribe.
Alright, let me know in the comments below how I went
what you want to see in the future
constructive criticism is always welcome
and see you next week.
I still have faith in you
I see it now
Through all these years that faith lives on