I ATTEMPTED TO START MY FLOODED GT3RS THAT I REBUILT

Autos hacks
81 followers
5 Video Views·Dec 1, 2025
I attempted to rebuild this GT3 RS engine and failed.
Oh my god.
I had to buy a brand new cylinder block from Porsche after rust ate away at the old one
because the car was fully submerged under water.
Woah!
Oh my!
There's water in everything.
But due to a stupid mistake, which I'll explain, we now have to strip the engine apart again.
Then we'll build it all back up again and hopefully we can get the first start on this car.
Here goes nothing.
First thing off, the cams with the chain.
We know how to do this because we only just put it back together.
So why are we taking this all apart?
Well, when we first bought the block, we noticed that there was markings on the side of it.
Eight letters to be exact.
We didn't think much of it until we got right to the end of building the engine
and we got told that these letters actually correlate to the size bearings
Now we would have been completely fine if the letters on the new block
matched the letters on the old block.
But unfortunately, they didn't.
So now we've got to strip the engine down far enough so we can access these main bearings
and push them out and replace them with the right one.
Here we are again at the crankshaft and the block has been split apart.
Here's where we went wrong.
These bearings here which spin, watch the crankshaft spin on.
These little things here inside there,
which is half in that side and half in the other side of the block.
Now they're actually different sizes depending on the block.
Don't know why, probably because the machine different, not sure.
We need to get the right side bearings now and put them in the right holes here
just for peace of mind because that way when this is spinning at 9000 RPM,
we're not going to worry that it's going to seize up
or the bearing is going to excessively wear because it's sitting tighter on the crankshaft.
Now you can see on the old block, they were all G bearings
and on the new one, there's three Bs and one R.
A B is a thicker size bearing and an R is a thinner size bearing.
But how different can they really be?
From looking at them, you can't tell.
You're not, but you wouldn't tell the difference in size there.
So we got the micrometer out just to see the difference.
98,000 of an inch, bringing in the blue one.
So it's got to be smaller than a thousand.
Oh my God, it's like a fraction.
Do you think it was worth taking the engine apart?
What for that much?
We'd have had to find out on the track, wouldn't we?
There is really a minuscule difference.
Now we've marked the blocks with what bearings
so I know which bearing needs to go into which bearing slot.
So now I'm taking out a yellow bearing,
which was originally in there,
which is a middle size bearing
and replacing it with a blue size bearing
as it states on the cylinder block.
Then I've got to go to another one
and replace another yellow size bearing,
which is a mid-size with another blue bearing,
which slides just behind the crankshaft.
There's then another blue one to do
and finally a red one at the end.
And then I've got to do the same on the opposite side of the block.
Then they'll all match up
and the clearances should be spot on.
Right, now we do everything all over again
until we get to where we were before.
So let's put this full engine back together.
Then we can time it up and hopefully it'll work.
Come on.
Now you guys seen us rebuild this engine in the last video
so we're going to steam through this as quick as possible.
We've got a bit of flange sealing on the cylinder block
and then we can slide the other half of the block
to marry it up as one.
And then we've had to order some new bolts to bolt it together.
After that, the pistons go in,
we connect them up to the conrods,
then the head gasket goes on,
then back on the cylinder head with again new bolts.
We've got to torque that down all to spec.
Then it's time for the shims
and this is a lot quicker to do
when you've already done it once before.
Once the shims are in,
we can lay in the two camshafts which sit on top.
One for intake and one for exhaust cam.
Now it's time for the timing.
I have to put this pulley on the bottom
which only goes on one way
and once that's on, I can pop on this device
which allows me to turn over the engine
and I have to turn it to top dead centre
and then lock it in place
which is actually marked on the pulley as OT1-4.
Top dead centre is where piston number one
is at the top of the cylinder, dead in the centre.
Once that's done, we can hold down the camshafts
with these camshaft caps like you can see here.
Now in order for these camshafts to actually rotate,
we're going to need some gears at the end of them
and that's what we're installing next.
Now it's about to get complicated.
This is a vital part now,
timing this part of the engine up
with this part of the engine.
Everyone knows now that the crankshaft spins
pushing the pistons up and down the cylinders
and these camshafts here are in charge
of pushing the valves open and close.
Now they've got to be in perfect timing with each other
and the way they do that is with this chain.
The chain will always be rotating the crankshaft
and the camshafts at the same time
but we've got to make sure this camshaft
and this camshaft are in the correct position
and the way we do that is with a special kit
and here is the special kit.
This actually bolts to the cylinder head
then uses this kind of fork
which slides over the camshafts
and these will only slide over the camshafts one way.
If I was to put the camshafts in upside down,
that black fork wouldn't slide down over the top of them.
Now to lock the cams in place
to make sure they're in the proper position
and then tighten up this tool
and you can now see that the fork is sliding over the camshaft.
Now we know that these are locked into place.
Now we've got to tighten this chain up
so it's nice and tight with the fake chain tensioner.
This is another special tool just to tighten the chain up
because if we time the engine up with a slack chain
as soon as we start it, it could skip a tooth
but now it's nice and tight.
Now we've got to tighten these onto the camshafts
so they won't spin.
At the minute, those cogs at the end of the camshafts
could spin round without the camshafts spinning
but to lock them onto the camshafts
I'm putting in these two special bolts
which you can see me doing now
and then I've got to tighten them onto the camshafts.
All pretty technical.
I've locked this tool in place which holds the locking nut
and then I've got to use this special tool
which looks like a flower to put on the end of that nut
and tighten them onto the cams.
The initial tightening is 30 Newton meters.
This is just enough to lock them on.
Once the initial tightening is done
I can then go back and remove the cam locking tool
and once that's removed
I then have to tighten up that nut another 40 degrees on each cam.
If these were to ever come loose then the engine is toast.
After that I can remove the fake chain tensioner
and replace it with the actual one
which will only tighten the chain once we have oil pressure
and of course that has to be torqued in as well.
So this should now be all timed up this top side
and the only way to really see if we've done well
is to turn this thing over
but we can't turn it over with these temporary caps here
which are actually holding down the cam.
The thing that holds down the cams is the actual rocket cover.
We've got to remove these caps but we can't just remove these
because the cams will just go hello.
So there's a special way of putting the rocket cover on.
Let me show you.
I first have to remove these two plugs on the side of the head.
Once I've removed them I can then slide in these kind of forks
which hold the cams down
and once the cams are held down
I can then begin to remove these temporary cam covers.
It's all a big learning curve at the minute.
We've never done this before.
Here's the rocket cover.
You can see on the underside of the rocket cover
where the cam's going to rotate on
so we can slide that rocket cover into place
torque it all back down
and then we can remove those little prongs.
Now these
because the rocket cover is now holding down the camshafts.
Now we need to see if the engine actually turns over.
Do you think it's going to work?
67% sure.
We actually need to turn it 360 degrees
before we start doing the other side
and it was going.
It's looking good.
Here's your dock, here's your dock come in.
It's looking good.
Yes, that turned.
That's good news.
We've just got to do it the same on the other side now.
We've got to do exactly what we just done on there
on the other side.
Let's smash it out.
We seem to have successfully timed up on one side of the engine.
Now to do the other side
we needed to turn the crankshaft around 360 degrees
and then lock it back in at top dead centre.
Now we can fully assemble the other side of the engine
doing the exact same thing that we did on the other side
and this engine works opposing to each other.
When one side's about to ignite the fuel
the other side's about to suck in the air and the fuel mixture
which is what keeps this car perfectly balanced and sounding good.
So it's vital we get it right.
Big moment.
Both sides of the engine are now timed up.
Slightly complicated, slightly confusing
but we think it's there now.
Now it's for the moment where I can unplug this from TDC
and hopefully this engine turns over
and no pistons hit valves and it's nice and smooth
and that means we can build the rest of this engine up
with all the ancillaries on it, all the wiring
and with that step closer to getting this to its first start.
Let's turn it over.
Good.
Oh that's good.
What's that noise?
What noise?
I would celebrate but it's not turned on yet has it?
But that is good, that is good.
We've done summit, we've done summit.
Right let's blast this out, come on.
We're never really going to know whether we've done it right
until we get that first start
but now that the hardest bit is done
all we've got to do now is start attaching
all of the parts which make this engine work
now I'm onto the high pressure fuel pump.
This bucket slots in here
which actually rides on a separate part of the cam
which pushes up and down on this spring
when the engine's turning over
on the high pressure fuel pump
that then pumps fuel out of the fuel pump
at high pressure down this line into the fuel rail
and here is the fuel rail
and at the end of the fuel rail is of course
the three injectors for one side.
I've got to slot this into the side of the engine
and bolt it to it making sure that the injectors
are fully seated and then my dad can tighten up that pipe
which goes from the fuel pump to the rail
and that is pretty much one side of the engine complete there
now moving on to some seals
my dad's just knocking in the crankshaft seal here
if we don't do this right
it's going to be leaking a lot of oil
seal in
that's not how you're supposed to do it
but it's in isn't it
now we flip it over and do the exact same thing
on the other side
remember this is a flat six engine
three cylinders on one side
and three cylinders on the other
once that side's done
we flip the engine upside down now
and start working on this part
because this engine has a dry sump
it doesn't store all the oil at the bottom of it
instead the bottom of the engine is used for this oil pump
which I'm attaching now
which is driven by a chain
which also connects to the crankshaft
but there's no timing needed on this
but it is vital that I torque up the bolt
which connects that cog to the oil pump
because if that fell off
then we'd have no oil pressure
it's time to put the rest of the casing on
and after that I need to fit the oil cooler
this has coolant flowing through it as well as oil
because the coolant would actually cool down the oil
but it's vital we put all the seals in
because we don't want coolant mixing with the oil
now that that's on
it's time for all the ancillaries
the water pump
a load of pipes
which connects parts of the engine up
from left side to right side
the thermostat housing
which my dad's adding now
and instead of a chain which drives all of this
it's going to be driven with a belt
to get the belt on
we've got to put the tensioner into this position
and lock it in
but there's a few bits which are missing
the alternator which we're hoping works
and the air con compressor
and once we've fitted those two
we can then apply the auxiliary belt
and release the tensioner
and that is job done
look at that
next up it is this wiring loom
we've been dreading this
because we just kind of took it off
and that was about it
so we're just going to try and put it back on
the way it come off
and this the starter motor attached to it in all sorts
there's no pattern on how we took this off
so we're just going to try and put it back on
and go from there
but we are so so close now
have you ever put a set of wired headphones in your pocket
then got to pick them out minutes later
and then had to untangle all of them
well this is like that
but times a thousand
but luckily i took some photos for reference
so with some time i managed to work out where it went
along with that i'm also putting on the inlet manifolds
part of it is new
because the old one was damaged
it had a huge hit on the left hand side
there was a bunch more stuff
which was also damaged in the accident to the engine
but most of it i've already replaced
the wiring loom
auxiliaries
and engine
is finally complete
ish
somehow we've done it
to an extent
here it is a four litre naturally aspirated
six cylinder
porsche gt3 rs engine
i really really hope there's not something that we forgot to do
or done something wrong
because anything in this car is an engine out job
for example the starter motor is
is down underneath here
and if you watch the rolls royce cullinan build
when that car went into about this much water
the starter motor went
but this one has been titanic underwater
the starter motor does work
because we did test it out
i believe that was in the second channel
there's a few things that are broken
so we've got this pipe here
which goes onto the fuel pump
which we replaced
and then also the wires
which go onto the fuel pump as well
because this whole left hand side did take a hit
alongside that as well
there's some broken wires down here
and there's some plastic
which sits over the top of the alternator
which was also broken
so we've got a few bits
few more parts to order
but we have got time
because in the meantime
what we're going to be doing is
attaching the gearbox and the flywheel
to the back of this engine
and whilst all this is happening
the shell is being painted
before we started rebuilding the engine
we removed the damaged carbon roof
both damaged a pillars on the shell
welded and riveted
new a pillars
and repaired part of the roof
after that the car got sent to allied automotive
so they can work the magic
on repairing the rear quarters
and soon after that
it was ready for paint
now you can pretty much order a Porsche in any colour
so it's impossible to choose one
which hasn't already been done
but before we see it
we've got to get this engine off the engine stand
so we can attach the gearbox to it
so we're using the two post ramp to hold it up
and then we can lower it down onto this pallet
right so what goes on to here now is
we need a seal in there
which we've got a brand new seal
but we have a flywheel
obviously the flywheel
the starter motor turns the flywheel
to get the engine going
this was full of water
you can see all the rust coming out of it
and it's got a lot of play in there
and I think it's like damp
I think it's like there's like dampeners in there
to stop it being so jolty when you pull off
like that's what the play is for
so normally you'd think
oh something like that's been under water
you'd think it'd be okay
but we're just a bit worried about that dampener thing
and if you have to replace it
it's an engine out job
so we didn't want to take the risk
and we got one for 1500 quid
a brand new one
which is here
and when we got it
this one
it's a lot nice
like it's a bit more rigid
than that one
which moves really easily
so we think it was probably the right decision
and for the peace of mind
so this has got to go on
after we put this rear seal on
another vital oil seal
if this leaks
it'll leak into the gearbox
and could even cause clutch slip
put a bit of lubricant around the edge of it
and now I've got to slowly push it in
and I've got to be careful not to pinch it on the way in
it's just about job done
after that
there's this little washer which comes with it
this can only go on one way
and once I put that on
it's time for the flywheel
again something else that can only go on one way
because there's a dowel on the engine side
to bolt it on
I've got to use some loctite on the bolts
and it's 60 newton meters to start with
every bolt goes to 60 newton meters
after that
they go another 90 degrees
that is tight
and that's one seal
and one flywheel onto the engine
how's it work out that one
gearbox can go on
but the gearbox
we're unsure about
because it has been fully submerged under water
but so did the Rolls-Royce one
and that did still work
but I didn't have any cracks in any of it
yeah this one has got a hole in the sump
here is our wet gearbox
which like the engine
was fully submerged under water
there's a lot of electrics inside of it
but our saving grace
is that the sump on the bottom of the gearbox
has a hole in it
so if any water was in it
hopefully it would have drained straight out
we might be okay
I think I've got a new sump
so we can wazz this off
and just have a look
see if it looks really bad inside
then we've got a huge problem
in the engine
the damage was caused
when the water just sat there on its own
which began to rust
whereas I'm hoping in this gearbox
it's either completely drained out
or it's sat with oil
and looking at the bottom here
it does look all clean
nothing looks rusty
yes the oil is fairly milky
it has mixed with water
but I think if we can clean this up
it just might work
new sump
and the sump is also a filter as well
we didn't really want to risk
stripping this gearbox apart
the best way we're going to find out
whether it works
is give the thing a service
attach it to the engine
and then try it once it's in the car
now we've got the new sump on
we can add a bit of grease
onto the shaft on the end of the gearbox
and the teeth on the flywheel
that it's about to join up to
and then me and my dad can guide the gearbox
onto the engine
and throw in the bell housing bolts
the one thing it won't start without
is the crank sensor
this is the last plug of the engine loom
that needs to be plugged in
and of course it goes to the crank sensor
which is on the gearbox
and with that done
we now need a car to put it in
the tub has just arrived back
from the body shop
freshly painted
we haven't seen it yet
it's the first time we'll be seeing the colour
go away
it's very blue
look at that
this colour is shark blue
i thought it was quite fitting
being that most of the car was underwater
and now that it's back from the body shop
you can never tell we've put two new a pillars on
and the rear quarters have been repaired
now let's get this thing started
Talisa the tub is back
i hope the camera is picking up how bright this thing is
this is well bright
and would you have even known
that this rear quarter was absolutely happy slapped in
you can see like the nice repair
that we've got here and here
lovely stuff
now anyone would think
our next step is to get this into Talisa
but we can't because we're still missing
those little bits off the engine
which we're waiting for
but if we do get that into Talisa
we won't be able to start it
because we need a few things to be able to start Talisa up
one of them includes the dashboard
because we'll need to be able to turn the key
in the dashboard to try it
and we're also going to need fuel
and we need a fuel tank
which is going to be in the front here
and i think it's a guess though
i think we're going to need brake pressure
because i don't think it's going to allow us to turn the key
if we don't have any brake pressure on there
so i think we have to put a brake pedal on
and the reservoir on
but before all of that
we can't forget to do the pyro fuse
our best friend
the fuse which cuts power to the starter motor after an accident
you can see the power from the battery goes to this side
and this fuse is broken
stopping power going to this side
down this cable
and all the way to the starter motor
for some reason
Porsche decided to put the pyro fuse right underneath the dashboard
making it nearly impossible to get to
you can see here the old one is broken
now for £8.49 off ebay
we have a new pyro fuse
and if i pop the cap off
you can see that this is what it's supposed to look like
the little plastic blows up
and breaks the fuse in a crash
but now that we're putting the new one on
we should now have power to the starter motor
and we hope we never have to change that thing again
that is all in
everything is committed to now
next up the dashboard
but we've got something to fix on that dashboard
which we actually got to before we got to this point
flashback
here's the huge box that we shipped back from america
full of the GT3 RS parts
and one of the parts inside it was of course the dashboard
and you can see the airbag's deployed and caused damage to it
this dashboard has blown
i think we found some people that can repair this
and then retrim it
but we have to get this part of the dash off
so we can give it to them to retrim
where do we start
this job was actually made much harder
with the dashboard being out of the car
but eventually we managed to strip the fabric from the frame
which holds the dashboard to the car
yes
now we can send this off to repair
along with some other parts as well
look
it's been repaired
and
re-stitched
we're also going to do the whole interior
this is going to be one of a kind car
so a massive thanks to auto trim for re-stitching this dashboard
i'm sure the rest of the interior that they're doing is going to look just as good
now we need to fit it
first thing to go in is the accelerator pedal
then the brake master cylinder
which slides through the back of the dashboard
and my dad's going to pull it through on the inside
there's a huge nut and bolt into the car that we're both tightening up
a few electrical connectors on it
and two brake lines going to it
all of which need tightening up
brake accelerator on
then it was time for the brake pedal
but we noticed something
yeah this is a european car not a german car
why do they call it german
why is it european
because look made in austria
made in poland
this part was made in the czech republic
this module was made in spain
part of the wiring loom was made in ukraine
the cylinder head was made in italy
and it just continued
and what have you found that's made in germany
the brake pedal
that's the only thing we've seen so far which is actually made in germany
so maybe it's just a huge combination of europe
but one thing we haven't seen is made in the uk
maybe there's a reason for that
next up the dashboard frame can be put in
this has also got the heater box on the back of it as well
we've got to slide it into place
making sure the pipes for the heater box thread through the front of the car
then it's time for those super long bolts
one each side
we've done this job before on a purple gt3
so it's a breeze for us now on the gt3rs
now i can put the hoses onto the heater box
and also the aircon lines
which connect from the outside going into the dashboard as well
then move back inside to connect up all the electrics into the dash
before we put the fabric of the dash in
we needed a new passenger airbag
i've got a new one from porsche
and this slides in underneath the dashboard and bolts to it
one new passenger airbag in place
now we're ready for the fabric to be installed back onto the frame
and then we can slide in things like the screen
which we still don't know whether it works or not
and all the air vents
there was the last few things to bolt up
before then we was able to test whether it all worked
now this part here when we picked up the car
this part was actually like missing
and the actual stop clock which is meant to go in the middle
it's like a stopwatch
is it wasn't in there
and i've not bought another one yet
because they are quite expensive
well actually from porsche like four thousand pounds
but we can get them on ebay for around 900 pounds second hand
but they all come in different colors
and my dashboard was yellow
it has yellow dials in it
but we still don't know whether that's actually going to work
for the instrument cluster
so until we know if that works
i don't want to jump to buy a yellow clock in the center
if we have to change the clock color on the instrument cluster
but let's see what happens when we put some power to it
so for now that is staying off
these do not look like they've been underwater
comparing it to like when we've just done the rolls royce
the inside of there doesn't look rusty at all
we're going to plug these in and we're going to see what happens
we don't know
like at the minute we've got all the modules off the
thalesa the german car
we're using the clocks out of the american car
and then we just want to see
well we just want to see if it works
if that screen works
i can't see why this one wouldn't
and there's only one way to find out whether it will actually work
plug both of the connectors in
give it a try
right i want to see if anything comes on
ready guys
am i heard a noise
it made a noise
okay so nothing at the moment
it's doing something back here
yeah blowing fuses
so in freddy's gt3 when you've got in it
all the screens come on on the car
and you've just put power to the car
and it's doing nothing
yeah there's nothing
absolutely nothing
good start guys
there isn't a lot for it to do really is there
all this all you wanted to happen with that to light up
well something at least
i mean we've we've actually made less progress
because in america the interior
oh come on now
we haven't even got an interior light
so it's not looking good for the electrics in the car
all of this stuff is super expensive
i've already had to pay for all of the modules
that are in the car at the minute
and i'm hoping i don't have to buy anything more
instead of stopping we were just going to carry on
the car was in pieces and there was a lot missing
and this could be part of the reason why some of the screens aren't working
firstly installing the carpet
which again was brand new
this car barely did any miles before it went into the water
time for this box
this box could be the reason why the screens aren't working
i think this is the thing that controls it all
so i'm going to plug all that in
slide that in the dashboard
and the thing that holds that in place is the center console
and in the center console there's more electrics
handbrake buttons
gear sticks
and all the climate controls
all i can do is install it all and give it a try
you can also see some of the new blue stitching as well
should we see if anything works now
all this is plugged into it should work
i don't want to take it apart again so
let's see let's see if that works
let's see if that works
action
yeah
yes
no way
whoa
that's going crazy
that's doing stuff
but that's doing stuff
that's doing stuff
but the clock still won't work
that's not working
okay
that is good news
we actually have something which works
minus the instrument cluster
but again i don't know whether something like the engine ecu
needs to be plugged in for that to work
so i'm not going to jump to conclusions now
our next step will be to pull the porsche into the lift
because it's getting towards that time
where we can fit the engine
whoa
here is the fuel tank
but what holds this fuel tank up is the front subframe
and we're not we've not got that far yet
we're thinking it's going to be better for us to put this on
once that engine's in
because we just want to hold that fuel tank up
so if we put that in now nothing's going to hold it
unless we put some straps on it
so what we're going to do is leave that until this engine is in
then we can wire up that to start the engine
before the engine goes in
we've got that hose to replace
and i've got a second hand one here
which i'm just going to slide onto the bottom of this fuel line
and then clip the other part onto the fuel pump
after that i can clip back in the electrical connections
then it's just the connector for the new fuel pump that we need to fix
and we've got one here off an audi loom
my dad's now going to solder that to the wires on the porsche loom
test the strength
strong that
well done
then put some heat shrink around it
a bit of loom tape after that
and connect it all up
job done there
after that there's some kind of bracket with a heat shield
which i think holds the exhaust
but for our first start we're not going to put any exhaust on
so if it does start it's going to be pretty loud
now it's time for our effectively brand new engine to go in our new shell
now if you were to check the old shell out that we bought in america
which has been fully submerged under water
out on car vertical
you'd see it's got a pretty bad report
it's got registered as crash damage
it's got a damage salvage title in america
but of course we're not rebuilding that shell
we're rebuilding talisa
and talisa is yet to be imported into the uk
we'll have to do that when it's fully rebuilt
do you think it'll start
i don't think it's going to start
you don't think it's going to start
i think it's going to come with an electrical glitch
huge moment right now
huge moment
now we can lower talisa down onto our freshly built engine
another good thing about car vertical as well is that your car
if your car was crash damaged
it will actually show you photos
when the car was at auction off at the car crash auction website
like this car on the screen
and on top of that it will tell you when it was damaged
and it also gives you a full record of the car
every time it's been bought
every time it's been sold
and every time it's had a license plate change
there we go
sweet
now the engine was in
we lifted up the car
but noticed a problem
uh guys
yes guys
very dangerous here
why guys
don't know if you saw the front ramps
oh my god
so some counterweights were definitely needed
to keep the porsche from falling off the ramp
and a few straps
but once it was all safe
we can then go back underneath it
and tighten up all the mounts to the chassis of the car
another good thing about car vertical
is that it works in over 20 different countries
so whether your car's in america or germany
you'll be able to find the full history of it
now i've got some wires to connect up to the gearbox
and the gear cable
and most importantly
this power wire
which is for the starter motor
it connects up to this terminal here
and without that connected
we would have no chance of this car starting
the engine is in
there's still stuff to connect at the top
but one thing we do want to check before we put any fluids in
is that the one thing we didn't change
is the diff oil
and there's gearbox oil
and there's differential oil
we're just going to undo a drain plug on the diff
just to see if any water comes out of it
because then it has been contaminated with water
which is highly likely
and if it has it means we've got to fill it up
with some new diff oil
let's do it
water guys
oh i thought we was past this stage
guys get another one
oh my god he's got he's got like poo in it
oh my how much water is in there
if you want to check your car out of car vertical
and you don't want anything like this to happen
i suggest you do that with the link in the description box below
and use my discount code
which is on the screen here
for discount on that check
oh i thought we was past this water stage
all right here we go
second drain on the diff
what the hell
whilst that's draining out
because there's a lot of water in there
we're gonna put some engine oil in there
well it was a good job we drained the diff oil
well what was left of it
whilst we don't need diff oil to actually start the car
we think we will need engine oil
this is the oil specifically for the rs engine
and everyone's wondering why we're using this disgusting brand
in your opinion
in my opinion
so in goes eight liters of this oil
and it's a weird color as well
it's green
but we've been told specifically from Porsche
that if it's a fresh engine
we must use this oil
right with the modules out this German car
because we had the body control module
we thought it was a good idea to take the engine ECU as well
bearing in mind ours was soaking
this could have been a very bad mistake
because the American engine
and the American gearbox
has different things on it
to what the German car would have
so German cars have OPF filters in the exhaust
Americans don't
I don't know how much of this is going to matter
whether this is going to work
and talk to the rest of the electronics of the car
this could just
this could be absolutely a nightmare
but at least it isn't wet
so we're going to give it a go
essentially all we're doing is making sure
we use the German body control module
and the German engine control module
because if we mix and match them
it's likely that the car won't work
but we don't know whether the American engine
is going to work with the German module
here we go guys
first off let's see if the cocks work
with the engine ECU in
this is our last grasp
at seeing if the instrument cluster works
now that the ECU is plugged in
nothing at the moment
no I think we need the key
oh I thought it'd come on
I thought it'd actually come on then
it seems to be completely dead
this is all working
but this ain't
the question is
do we need that to start the car
and also do we need brake pressure to start the car
and also can people be repair prepared
if it does start cranking and don't stop
now at the minute
we don't have any spark plugs in the engine
because we wanted to firstly crank over the engine
without having a spark
so the engine's got chance to build up oil pressure
before it starts running
and also we don't have any fuel tank
which means we don't have any fuel
but to be honest
I don't think it's going to crank
unless we have the brakes on
because I think that you need brake pressure to start it
you ready
I'm going to push the foot on the brake
I don't know what it's saying
but if it cranks
and it doesn't stop cranking
we need to disconnect the battery
oh it's brake fluid Alan
oh my god
it cranked
I was not expecting that
oh my god
yes
what the hell
the engine actually turned over
we've got to try again
yes
it cranks and it didn't
yeah but a valve did it at the piston
now you've said it
no way
so we need fuel
and we need spark
so we need fuel tank on
and we need spark plugs on
and this thing might actually start
no way did that just work with the car in this state
but before we started it
we had a few more things to do
some days have passed
and we're now ready for the big moment
but we've got some theories
so our screen here
that isn't working
everything else is working
but that isn't working
which seems like a coincidence
we have got
the engine ecu out of the german car
the body control module out of the german car
and clocks out of the american car
and to get the clocks to work
with the german modules
they need to be coded
so it's possible
that this works
but it's not coded to those ecus
that would be good if it does
but worst case
we have got the clocks from the german car
whether we
whether we're gonna have to use them or not
I don't know
there is a downside
oh no that's not as good
they're not as good
they are red
but these should
they should work
worst case
but i'm hoping
we don't have to use these
and we can send it back
how much were those?
three thousand pounds
for this instrument cluster
we can send it back
we just want to see if it works for this point
but the thing is as well
this might not be good for anybody else
because it needs to be coded to the car
and like we don't know anyone that can do that
but if we can find someone could do that
we might be able to get all clocks working
what mileage it's going to say
we have no idea
we'll try this when we start it
because we need to know what is going on with the car
whether we've got oil pressure
whether we've got any any energy management lights or not
so we'll try this
and in the meantime
we need to start fitting the spark plugs
so now we can finally get some spark
and actually
oh yeah we need spark and fuel don't we
spark plugs first
now we can install the spark plugs
three on each side of course
i'm doing one side whilst my dad's doing the other
once the spark plugs are in
i can then bolt the coil packs to them
and slide the electrical connectors onto the top of them
and my dad's done the same on the other side
and it seems now that the diff has leaked out all of the water that was in it
so we thought it was a good time to add some oil to it
okay we decided it's a better idea to fill it with gearbox oil before we start it
first thing we're going to fill is the diff
so the drain bung goes in there
and then there's another drain bung which my dad's put in there
and to fill it we have to put it in up here
which looks like what size?
21?
we've just got to crack this nut off here
remove it out fully
and then fill the diff up with oil
which we've got from Porsche
apparently you just fill it up until it starts coming out
then you put back in the fill plug
and the job's done
that's enough, fill it till it comes out
i've now got to make sure that the fill plug's back in
tightened up
and then we can move over onto the gearbox
which is a slightly different procedure
right so the procedure for this
we think we've got it right
add PDK fluid into the fill until it starts coming out the fill
then run the car
providing it does run
up to 40 degrees
until the oil is 40 degrees in the PDK
and keep filling until it comes out
the thing is we won't be able to actually run the car up to temperature
because we don't have any coolant or any radiators on it
so for now we're just making sure that there is oil in the gearbox
so we don't make any unnecessary damage when we try and start it
the fuel tank
a little bit of fuel in there ready to start it
and last but not least the fuel tank needs to go in
we've got the spark plugs in for the spark
we just need something for it to ignite now
the fuel tank sits right at the front of the car
and we're going to lower the car down onto it
we're going to connect up the electrical connectors on there
and the pipe which takes the fuel from the fuel tank
and also the fuel return line
fuel tank is in
plugged in
ready
i think we just need power now
and it'll go
that's it
yay who needs all the other stuff on the car
we're about to find out if you need any more stuff on the car to start it
we're about to answer a lot of unanswered questions
the last thing i wanted to do
is take off the instrument cluster that isn't working
and plug in the german one to see if that worked
do you think it's going to start
i always like to have faith
yep
so i'm going to say third try it's going to start
third try okay
do you guys think it's going to start
there's nothing on it
probably not
no faith
here we go
one small step for man
we're trying to leap for mankind
12 volt go
oh
okay everything's on
look at the dash
oh my god i've never seen a dash light all that much
oh and we said we got 3200 kilometers
so this is this is reading off the german
german ecu
okay are we ready
i'm ready
okay
that's try one that's okay it's pumping the fuel
no fuel
okay what
try again try again
no fuel
so
shall i pop that hose off see if it squirts any out
here and here
with the fuel hoses
should i take one off and see if we've got any coming out
no
there's no fuel in there
hmm
yeah there's no fuel in there at all
none
so either it's not made it there but it would have you
when you turn the ignition on it should prime the fuel pump anyway
yeah so summit ain't right
this has got to be for the fuel pump
so is it missing off a module or something
i don't know
earlier we seen that this plug was empty
we couldn't actually work out where it was meant to go
there was nothing on the fuel tank but it looks important
we need to work out where that goes
yeah i reckon it can't go far look it's
unless it's like inside here
but then i took a look at the battery tray
this is on the battery tray
you think nothing to do with the fuel pump
just googled it
fuel pump computer control module
so if you take your battery tray out of the porsche
you can't start
so let's plug that in
apparently this isn't like
yeah the module for the fuel pump
so good job we didn't throw the battery tray away
so this could actually be our problem
if this module controls the fuel pump
then once we plugged it in
i'm on
we should have fuel
who would have thought
okay now now we got a big moment
here we go
now we're about to find out whether
one we've successfully rebuilt a porsche engine
and two whether you can dunk a porsche engine
completely under water
and all the electrics and sensors and modules on it
still actually work
there's the fuel pump
are you ready
i'm ready
go
here goes nothing
started
all the work that we've just done has finally paid off
we did it
if that wasn't worth subscribing for
i don't know what is
thanks so much for watching the video
if you enjoyed it hit the subscribe button
hit that thumbs up button
oh my god it's burning my eyes
and i will see you in the next video
where hopefully we can get this back on the road
peace out
what did they say you have to do to be a pro
three in a row
we'll go with two because three might be pushing
no we've got to go three
well i don't plan to be going back
it's been under water
