Фрезеровка гипсокартона под скрытую подсветку. Сложный элемент

Pavel Sidorik. Renovation and Finishing
79 followers
7 Video Views·Dec 11, 2022
Hello friends everyone This is Pavel Sidorik This video will be about how we mill drywall
Under the hidden lighting Here is our project This is a ceiling design made of drywall We have it around the perimeter
There is hidden lighting in almost all rooms There is even such a corner element
With the column and the corner Here we will have milling and here This is exactly the point I want to show you
I'll show you how we will mill mark and install this sheet It's the most complicated one
We have already done this room I will show this ceiling now We have already routed this niche It turned out to be
A very neat design This is how the niche looks from the inside Here is how the niche appears in a cross-section on the diagram
Drywall folded like an envelope and here it doesn't reach all the way There is a gap of 5 here
millimeters Here an LED strip is installed resulting in even lighting across the entire length
A niche The distance from the edge of the drywall to the wall is 10 centimeters here
The niche is about 6-7 centimeters in height This is all
It was filled with spackle covered with fiberglass mesh and painted There's no need to worry too much about it here
None of this will be visible Only about this part will be visible I suppose For
The framework used Knauf profiles The drywall is also Knauf 12.5 millimeters thick A few words about the preparation
The niche The niches are plastered filled covered with glass fabric and painted All of this was done
before the frame and rim were installed because if you do it after installatio
It will be extremely inconvenient to do so But when you have a workspace
Then it's very easy to do You can even do it with more margin than we did Here
We made the fritik but you can also just skim coat about 40 centimeters We start with marking out On the walls
We mark 10-centimeter intervals This is the outline of our niche After that using a laser axis
Building the structure aligning the line with the marks we transfer the niche outline onto the drywall sheet lying on the floor
Half This is very convenient The drywall sheet is cut as close as possible to the walls All excess will be removed later
Cut off All dimensions of the niche have been transferred to the sheet Now we can proceed directly to the next step
We perform gypsum board milling on the floor because the table is at another site
Honestly I just didn't feel like driving it Also I want to show you that milling is basically possible
It can be done under such field conditions The only inconvenience is that you have to
Work together because there is no way to fix the sheet with clamps We perform the milling
Around the entire perimeter where we will have a niche The difficulty is that this sheet goes around it
The column And it took a long time to calculate the dimensions to avoid mistakes Milling is done Now
We will assemble our construction Note how the drywall sheet is cut for
So that it can be folded with the envelope First the central square is cut out Then the corners
They will be cut at 45 degrees This can be done using a regular utility knife or a file
Drywall After all these manipulations the drywall can be folded It all worked out The same
We do it with all the corners First dust the seams and foam them Then assemble step by step
Check the right angle of 90 degrees with a square Secure with clamps After tha
We move on to the next element So step by step we fold the entire sheet Now
We can try the sheet For this we use a drywall lift Without a lift it was
It would be extremely difficult to do Right now we temporarily hung this sheet to get an idea
Did we make a mistake somewhere with the measurements The only thing is when we milled the drywall
We didn't take into account the thickness of the drywall This is a common mistake that occasionally slips from memory
It flies in And we ended up with a folded envelope that's just a bit too short And now we will
Remove the sheet and stick more strips here In general before installing the drywall sheet
Everything on the ground should be covered with a uniform coating filled in patched and all imperfections eliminated
The drawbacks are because it becomes extremely inconvenient to do it later in the niche How does the connection take place
Plywood So we just unravel this seam prime it fill it with uniflot and so on
Just cover it with glass fiber cloth No corner will be placed here Thank you for your attention This is
There were simple tips for repair If you liked it
of course like and subscribe to the channel See you again
