Hi, I'm Mike with House on the Mend. This is the Yotala 46 cubic foot garbage can storage shed.
I am going to go through the step-by-step process in this video of assembling it,
and spoiler alert, it is terrible. The other thing I'm going to do is break out the tape measure,
give you final dimensions on this product, and we're going to show how my standard
county garbage can does not fit in here, so you're going to really want to know before you make a
purchase what those measurements are. In theory, you are supposed to be able to lift up this lid
with gas struts, and at the same time you lift the lid, it comes with these little chains that
are supposed to lift the can up at the same time and close it. A really smart design,
however, I'm not able to show you that because my can won't fit. Nonetheless, here's my intro,
and let's get started with the assembly. Now I had been hoping to show you in this video that
we are solving the problem of this Great Pyrenees you see that's been roaming free around our
neighborhood, knocking over this can, and eating the trash out of it. However, as you'll see later
in the video, this can, which is our standard sized county garbage can in our area, does not
fit in the Yotala shed, so instead we're just going to be using a bungee cord to hold this lid
down and the critters out, and we are going to use the shed in the backyard to house our goat hay.
Well, every good video starts with a little drama, a problem that needs to be solved,
and look at this from a recent snowfall. Our poor goat hay is all uncovered. The wind was so bad,
and there is nothing finer to a goat than stealing the hay rather than eating the hay that's supplied
for them. All right, everything comes in one box. It is 60 pounds in total, so have yourself a hand
truck or a helper to get moved into your final position, which for us is right here on this dry
poor concrete pad that I created. Now you could put it into gravel or just right down on the dirt
on your driveway for your garbage cans, but we get such strong winds coming from the south this way
that I need to be able to anchor it down, which is why I made this pad, and it's perfectly positioned
right near the door that leads into the goat pen. You can see the little snack shack back here
off to this side is their house that I created in a different video, so this is going to be perfect
to keep their hay nice and dry and free from critters getting in there and making nests and
disgusting things like that. So let's see what comes in the box. I'm going to stand it up, and I have
a razor in my pocket. I'm curious to see is this the type of project that
just snaps together, or is it going to be 200 screws? And I would imagine if you
if you came to this review, you're wondering the same. Now during the entire time we're out here,
my roosters are going to be crowing. They're so excited. It's a nice sunny day. It was just snowing
yesterday, if you can believe it. All right. All right, as you can see in this picture,
the first thing I notice is lots of smaller parts, but they're all metal. We have some gas struts.
That's awesome. And then right over here is a manila envelope that I'm assuming
has all of our screws and hardware in it. So let's get set up and start building. All right,
first thing I noticed is the common parts that you need. They're all pressed together,
and you can't easily get them apart. So your best friend initially is going to be a prying tool
of some sort. So you can get in here and try to break these parts free from each other.
That's not easy. Look at that. Now, as you can imagine, working with sheet metal that's all
stamped and pressed and everything, every bit of this is razor sharp. So they were kind enough to
give you a couple of pairs of gloves to try to protect you. But if you look here, they'd never
fit a grown man's hand. So make sure you have something available so you don't get all cut up.
So the first step is to put the four pieces of the base together. They are clearly marked.
Now the instructions aren't that helpful, but you want to go large hole over small holes,
just like that. You put a screw in each of these two holes, and then you take
these corner brackets. They go right into the spot, and they get four more screws to hold
everything square. The screws are clearly marked as F1, and I've got them in this little tray so
they don't go rolling away when you're all done. You want it to look just like that. And as you
can see, stamped out of the center here are your anchor points. So there's four of them to hold it
down so it doesn't blow away. With the base frame done, I'm starting on the two sides, and they're
clearly marked left and right. Now you have to get a little piece started and then peel off the
protective layer on every sheet. It's a hassle, but it is a nice feature that in shipping they're
not getting all scratched up. All right, with that done, I can start putting this second piece down
here on the base. And they go in with the same F1 screws that we used to put the base together,
and then right in the center of the two sides, there are holes for a nut and a bolt, and we'll do that
right after. All right, on the wraparound piece, there's another spot for a screw to go into.
However, I'm going to wait to put that one in until we put the front and the back on. Both sides are in,
but before we put the back on, you need to put on these supports right here. They go in from the
outside with the same F1 screws, and they make it easy for you. They're marked right here, left,
and right here, right. So there's three back pieces. They go in the same as the sides,
F1 screws all along the bottom, and in the centers to join the two panels together,
you have these nuts and bolts right here, and I put Loctite on each of those. So this top
support bracket that goes all the way along the back is L35-4, and it has these little rounded
notches here, here, here, and so on, and that little round notch out gives you the ability to get your
screw and screwdriver in there to secure it into place. So that's how you know which way to put it
is the little notches are on the outside. So once that's in, you've got this open joint here that we
want to stabilize next with this corner bracket. It's going to use the same F1 screws to go three
screws here, three screws here. So next, we put in our first piece of block trim right here. It's L35-UA.
It was wrapped in the plastic cover before it was bent, so it is impossible to peel that
clear sticky film off of it. So I gave up after 20 minutes because I want to get this done.
Nonetheless, you can see right here where it is notched out to go perfectly over this rail.
Then you'll put an F1 screw in this way and that way. The one here coincides with this corner piece
and then right here in the center again, you will put in a nut and bolt. Once both pieces of side
trim are up, it's time for L35-5, this crossbar up here. And very similarly to the back, you get one
F1 screw on this side and one on this side, pinching all of this corner trim and this little
side piece all together. Once that's done, you have the same three sets of holes on both corners here
for this corner bracket and six more F1 screws. Next, right near the front corner here on this
side piece with the four holes in it, we're going to put in the L35-14 brackets. They are identical
to each other. Just make sure that the three holes go to the back so that you can put on this
little guy here that the air strut is going to connect to. And he gets put on with just the same
F1 screws. Well this L35-7 piece is supposed to go up on top next and it has holes in it on the left
side. Annoyingly, you have to take the screws out you already put in to put this on. And then as you
come over here to the center, there's the hole and then they disappear. There's no hole there,
no hole here, here, here, or here. So that's pretty annoying. So the next thing was these little corner
brackets up on top. They screw in right through the metal here. And then if you look here, you're supposed
to put this piece right in the center. But if you come over here and you look, this doesn't line up
at all. So that's just terrible. Next thing is to start on the lid or the roof. So I have four panels.
There's three that are the same size and then one skinnier one right over here. And then these two
L35-11 brackets. And they each get the F2 nut and bolt and then also a plastic washer.
And of course, I've used blue Loctite on all of these. Well, it's so windy I had to move inside.
So after putting on those unpainted brackets on the bottom here and screwing them all together,
it's time to put in the four pieces of side trim. As you can see, they do a great job of dressing
up that corrugated metal. So these short side pieces go on first and they get screwed down with
the same F1 short threaded screws right onto these brackets. And then you slide on these long
pieces here. They go through the big hole on here into the small hole on this piece with the short
F1 threaded screws. Now this side over here, it doesn't matter which side you put the long
strips on. You can see it has four sets of three holes right there, there,
there, and over here. And that is for the hinges. So this is going to be
your rear piece that will rotate up like this on those hinges. Next step is to flip it back over
and put on the gas struts, all four of these hinges, and this little latch that hopefully
we can figure out a way to make latching with the piece where the screw holes didn't line up.
All right, with a little help from my wife, we brought the door out here and put on all four
hinges. And then you just press in the air struts into the little balls. They click right into space
into place. Now the one thing I did notice when you shut this top is it wants to stay open all
the time. So once we figure out how to get the little piece in about right here that'll hold
that, all it's going to be holding it down to protect everything in here is this tiny little
latch. So I'm not sure how well that's going to work out. So since the holes aren't here,
there's just this one notch. It looks like what we're going to have to do is put an F2,
so a screw and a nut here, and then an F1, so metal screw, on that side. Well,
call me ye of little faith, but I don't know if that's going to hold under the winds we get here.
Next, we're going to start making the doors. And sadly, they come in two pieces
to fit inside the box. So you have to join them with the F2 screw and nut. And then we start
putting on these cross braces to add rigidity to the door. And those attach to this front
piece of trim here. There's a cutout for some latch hardware that'll go on later.
And then it's the same thing here. We have the big hole, the little hole inside that's going to get
a screw. And it's the opposite over here. We have this little hole and then a smaller hole on the
trim. So I'm thinking of going like this, if possible, and then putting the other piece of
trim right across that. Now, in the center of these braces, it's actually slightly off-center,
so there's only one way they'll go, is another F2 screw and nut. And all of those I've put
Loctite on. And it goes together just like this when it's all said and done. Looks nice and sturdy.
And if we flip it over to the front side of the door, we'll have four more screws in all of these
corner holes. You can see it just lining up right there. Well, it's been an hour, and just like I
feared, this lid is not staying shut by this little mechanism alone. So maybe we can get a screw or a
pin that we can put in there to cause a positive block. Once construction of the doors is complete,
you can see these hinges have a very distinct screw pattern. There's no way to get it wrong.
Thankfully, all the holes are pre-drilled, so that's pretty easy. You come out here,
you put them all in, and you have the little latches right there and down at the bottom.
To hold this one door in place, and then the other one swings free and latches in. Speaking of the
latch, there's a very distinct pattern, so you can't get the latches wrong. This one has four
screws, so it is stuck in place. But this little one here is adjustable, so you can get the height
just right. Also, beyond that adjustability, if you look up here and you see you're off a little bit,
you really only other adjustment is by racking it back and forth. You can see
it does make a difference. Now the kit comes with a whole bag of these little rubber screw covers.
Now this whole row here are the sharp F1 screw tips here, but interestingly they barely fit on
those. They seem much better suited for these F2 ones. It's a very good fit. So if you don't want
whatever you're going to deposit in here being scratched, you can use these and go all
the way around. Well now we come to what might be the comic relief section of the video when I try
to put our county's standard size trash can into this bin. If you come from a place where you get
maybe a trash and recycling of smaller size, you might have a better time. But let's see how
something this big does. So because of this crossbar, you can't just roll it in, so you're going to have
to bring it up close and then like this. There you go. Yeah that's nice. So obviously our can
is too big to go into this garbage can shed. Not only is it too wide from the handle to the front,
but even at this angle it's already too high to shut the lid. Now if you're fortunate enough to
have a smaller can, this chain that's included, there's two of them, would clip onto the front
just like that. You can see how it's going to pick up the can and then you loop that chain around
right here on this support bar and it's got a little mini carabiner hook right there that you
loop around and clip anywhere you want. Thankfully that's not our intended use for this shed. We're
going to be putting goat hay in it, but if it was your intended use, let's go over some final
measurements so you can go out right now before you hit purchase and measure your can. So our can
from the handles to the front is 32 inches and we're about 42 inches high here, 44 inches high
here. If we come inside to the ground it's about 45, 45 and a half inches high right here
and 28 inches from the back to the front. So there's just no way that it's going to fit in here
especially distance wise out. Now if you wanted to try to wedge it in sideways,
that's exactly 28 inches so you'd still be running into problems. So
let's give you a final measurement across this way that is 51 inches.
Hopefully that helps you make a decision before you purchase this one.
And there you go, there is my completed assembly and review of the Yotla garbage can storage shed.
Absolutely terrible to assemble. Visually it looks really nice. This latch hardware is very good.
This is terrible. The pistons back here, the gas struts are very strong. They could probably be
about 30-40% less tension pushing upward and this might stay put. So I'm going to drill a hole
right through here and put like a large framing nail in there to hold this lid shut. So we're
going to just put our goat hay inside of here and keep it out of the elements. So functioning these
doors here will be perfect for us. If you found this video helpful will you please give it a
thumbs up. It really helps the channel. Also drop a comment below if you have any questions on
anything I didn't cover. I did edit down to try to make the assembly process streamlined but
it's hard for me to judge the amount of time because positioning cameras and doing all that
at least doubles the assembly time in my experience. But I would say it took me a full
day to day and a half to assemble everything and get it all put together. So I would definitely
give yourself some time. If you are a handyman thinking of bidding this project, I wouldn't
do it because it's going to take you at least eight hours and it's hardly worth the price for
the customer. I think it would be a real decision that they would have to make on whether or not
they want to hire you for it. So let them know up front. Send them the link to this video and let
them know what your pricing would be. Nonetheless, I'm going to leave several links in the description
for this product. I will leave the Yodalo website link with this exact model. It comes in three
different colors. If there is an Amazon affiliate link, I will put that in the description below.
And if this product is offered through YouTube's link affiliate attachment program, I'll do that
too. Whichever one makes you feel the most comfortable, you can check those out. Until
next time, thank you for watching. Hey, that's my coffee. You can't have that.