Router Bit Speeds, Feed and Types

House Love
61 followers
1 Video ViewยทNov 15, 2022
Router Bit Speeds, Feed and Types
The next video in our series about routers,
we are going to talk about router bits, feeds and speeds.
I wanna go over the variable speed on your router,
which was one of the biggest questions I had.
I wanna talk about the feed speed,
the amount of pressure you're putting on your router
when you're cutting something.
And I wanna talk about different types of bits in depth.
I covered that briefly in my router basics,
tips and tricks and buying advice video,
which will be linked right here.
But I wanna get more in depth
and talk about different spirals, up cut, down cut
and different types of bits and what they do
and what I think are the most useful.
So let's start by talking about the speed
of your variable speed router.
Most routers today have variable speed
and most of them will have numbers on them like this one
from one to six.
Now, one of the biggest questions I get is
what speed do I run my router bit?
Well, there are some simple rules to this,
but first I wanna explain why.
So I want you to look at the inside circles here.
We have small, medium and large.
Now let's say that you could only walk one speed.
Let's say that was a mile per hour.
It would take you less time to get around the outside
of this circle than it would this one
and this one would be less time than this one.
And what that means is when your router is spinning
at a certain speed, let's say one mile an hour,
the inside of the bit is gonna be going one mile an hour
while the outside is going, let's say two miles an hour.
I know that's not the right math,
but that's just an example.
So how do you know what to do?
Well, first of all,
you wanna look at the manual for your router.
All of those are available online.
You can download as a PDF.
It will assign values to those numbers on your router.
It may be different for each brand,
but for me, the number six on my DeWALT router
is 24,000 RPMs.
The number five is 21,000 RPMs.
The number four is 18,000 RPMs.
Three is 14,000, two is 12,000 and one is 18,000.
So how does that translate to bits?
Well, router bits under one inch like these here,
you can run up to 24,000.
If you're having problems with burning,
you can slow down your router
or adjust the speed at which you're pushing.
We will talk about that in a second.
Bits like these, which are one and a half inches wide,
you're gonna wanna run at 18,000 RPMs.
So under an inch, full speed, one to two inches,
18,000 RPMs, and then up here, two to two and a half inches,
you're gonna wanna run at 16,000 RPMs
and three inches and above,
you're gonna want to run below 12,000 RPMs
and you could make adjustments
depending on the type of cut you're getting.
So that's some basic rules.
You're gonna wanna make adjustments,
but honestly, most bits that I own are under one inch,
so I don't really worry about it.
When I'm doing big roundovers like this,
sometimes I'll still run it at full speed
and just take smaller passes.
Like we talked about in our previous video,
you never really wanna take a bigger pass
than half the diameter of the shank of your bit.
So with this bit,
I would probably take three quarter inch passes
and if I was getting a good finish,
I might not adjust my router,
but for this one, for example,
when I'm flattening slabs with this,
I absolutely lower the speed of my router
because it just makes such a difference
and you have to push a little bit slower,
but when you're moving this big of a bit
and removing that much material,
you really wanna slow down
to avoid getting a bad finish or burning.
Let's talk about how fast you're gonna push your router.
All right, so here I've put a quarter inch upcut bit
in my router and I'm gonna show you
the speed at which you wanna push.
I think if I had to assign a value to it,
it would maybe be a quarter inch a second,
so it's very slow and it's very light pressure.
You don't wanna feel like
you're really shoving your router.
You wanna feel like your bit is cutting
and you're moving at the speed
at which it allows you to move.
What you wanna listen for is high pitch screeching
or your router jumping as you cut.
It means you're probably pushing either too hard
or you're taking too big of a cut.
Remember, refer to that don't take a pass
bigger than half the diameter of your shank rule.
And if you have your speed set correctly,
you shouldn't be getting those kinds of sounds.
So I'm gonna set up my router here
and show you what it sounds like
when you're getting a good cut
and when you're getting a bad cut
where you're pushing too hard.
Okay, so I'm gonna take my first pass here.
I'm taking almost a half inch pass
and you're gonna hear the sounds,
the screeching, it'll be alternating sounds.
You want just a consistent buzzing cutting sound.
I don't know how to say it better than that,
but I think you'll hear here
when we get the screeching and jumping
that happens when you do too much of a cut.
Okay, so you heard all the screeching that was going on
and that was just too big of a pass
and I was pushing too hard.
Now this is what it should sound like
when you are making a correct pass.
So you can tell there was a huge difference in sound there
and there was two problems.
One was we were pushing way too fast
and also we were taking too deep of a cut.
You can see this black line here.
This was our first cut and this was our second.
So you should get a nice consistent sound
without screeching and squealing.
If you're going too slow, you may get burning
and you'd wanna adjust from there,
but you want to be pushing as fast as your router will allow
without any resistance.
That's feeds and speeds.
Now let's talk about in-depth different types of router bits.
As you can see,
there are so many different types of router bits.
In fact, I built this cabinet a couple months ago
which was sponsored by Bits and Bits,
my favorite place to buy router bits.
There's a discount code down below
and I have free plans for these whole layouts.
If you wanna build something like this,
that video is linked right here in the corner,
but don't let this intimidate you.
There's really only a few types of router bits.
The first ones I wanna talk about are straight bits.
Straight bits come in a variety of diameters.
You can get them all the way down to the 16th of an inch
up to I believe inch, inch and a half, something like that.
There's spiral bits like this one here, compression bits.
So this cuts up and down and straight bits.
Now this is from like a garbage Chinese set I got
and these dull and break really fast
and I hate the straight cutters
because you get tons of tear out and everything like that.
They are a lot cheaper,
but I much prefer spiral bits for a couple of reasons.
One, they clear chips out of the cut.
One of the causes of burning
when you're cutting a dado or a groove
is that you get heat buildup
and if sawdust is staying in your groove,
your router bit is not only working to cut the material,
but it's working against all that sawdust
that is compacted in there,
which is why bits come in spirals.
One, you get a sideways cut, so it's like a shearing cut.
You get a much better finish and it clears chips
and it can clear chips up or down.
This is a compression bit.
A compression bit has an up cutter and a down cutter.
You can see this is a down cut and this is an up cut.
And what that's gonna do, one, besides clearing chips,
is a down cut is gonna give you a better finish
on the top of your board.
As you can see, a down cut is gonna force sawdust
and the cut going down.
This is great when you're doing through cuts
or really big grooves and dados
because the top of your board isn't gonna get that fuzz
that you can get with a router bit.
An up cut bit is great for, let's say, shallower passes
where you're not going all the way through
because it's gonna bring chips up.
However, if you are going through,
it's gonna give you a better finish
on the bottom of the board.
Now, you can see this is the same size bit,
but one cuts up and one cuts down.
This is the down cut bit.
As you can see, the bit would be spinning this direction
and it's gonna force chips down
and give you a better finish on top.
This is an up cut bit,
which means it's gonna scoop chips up,
clearing them out of your cut, keeping your cut cooler,
but you may get that fuzz on the top of your cut.
Like I said, you can get a variety of sizes.
I usually only buy quarter inch and half inch
because those are multiples of the types of cuts
that I usually wanna make.
And anything bigger than that, to me,
you would have to take such shallow passes
that it would take just as long
to get a cut in the width that you want.
These tend to work best for me.
Not saying you shouldn't get bigger,
but getting a good compression bit
for really big cuts
and a couple of good quarter inch spiral bits,
I think can do 98% of anything
you're trying to do with a router
as far as creating a square groove.
The next type of bit I wanna talk about are bearing bits.
Now, these come in three different types.
Bearings on the bottom of the bit,
bearings on the top of the bit,
or bearings in both locations.
Now, these are my favorite bits.
I've talked about these a million times
in my router videos.
Up and down cutter, bearing on both sides,
most versatile bit with the cleanest cut,
no tear out ever.
Love these things.
These are really cool,
these small ones with the top bearings.
I use these a lot when I'm just trying
to get a shallow groove for something,
like if I've created a template for our router lift,
for example, for the router table we're building
that should be coming out very soon.
These are great.
I've also seen Mike Farrington use these
to clean out for the tails,
I'm sorry, for the pins on dovetails.
He has a really cool technique for cleaning out waste
with these that's really neat.
These are great bits as well.
This is my tiny corner bit,
so when I need to get into really small corners,
this is great.
And these are great because they have a really big cutter,
so if I need to cut along a very tall piece,
these are wonderful.
These are my most used bits, I would say,
besides roundovers, which we'll talk in a minute,
but typically I use these about every project
for one thing or another.
So, let's talk about roundovers and edge profiling bits.
Now, these are the other types of bearing bits,
which again, follow an edge,
but these are for edge profiling in one type or another.
Now, obviously my most commonly used ones here
are my eighth inch and quarter inch roundover
as well as a chamfer bit,
but I do use these all.
These are a series of roundover bits
going from, I believe it's an inch, three quarters,
half an inch, quarter inch, eighth inch,
and these are great for a variety of applications,
including you could make your own dowels
in a router table by running the piece over it four times
and you can create a circle if you don't have a lathe.
These are chamfer bits for creating a 45 degree corner,
great edge profile,
really makes the project look really cool.
And then this is a rabbeting bit
that has different bearings,
so you can get different size rabbits
depending on the bearing.
And this is a bit, I don't use it very often,
but when you need it, it comes in really handy.
And this is sort of a specialty bearing bit.
This is called a rails and styles bit.
This is for making raised panel doors in a cabinet.
And you can see these bits perfectly match each other.
It's the negative and positive of each other
for creating the pieces of a door in a cabinet.
So edge bearing bits and flush trim bits
are my most used bits, followed by straight bits.
And then I have some very specialty bits
that I wanna talk about that I use occasionally,
but are very cool and certainly come in handy.
Okay, so here's some of my more specialty bits.
I'll go over them kind of quickly
because these may not be something a lot of you would use.
These are tapered ball nose bits
and lettering bits for the CNC.
So if you're doing some engraving, these are great.
This is like a 60 degree for very fine lettering.
And these would be for doing fine raised 3D detail.
This is a bowl bit.
It has a rounded edge, you can see.
So when you have an inside curve, you can create a bowl.
This is a keyhole bit.
This would be like the keyholes you see
in the back of picture frames.
So it will create a recess for a nail or screw underneath
while cutting the slot up above
so that you can hang a picture on the wall.
This is a slab flattening or spoils board bit.
In the CNC, you would use this to flatten your spoils board
or you could set up a router jig to flatten a slab.
These are a little less obscure, but they're great bits.
These are dovetail bits for creating sliding dovetails
on the router table or with your handheld router.
This is a ball nose bit.
You could create a rounded groove
like the handle for a cutting board
or creating shapes on the CNC.
This would obviously offer a lot less detail.
Now, these are my most obscure bits.
Really cool.
You've seen me use this one
in actually the router cabinet build.
This is a glass drag bit.
In fact, all three of these bits,
you would operate your spindle at zero RPM.
So these would not be spinning.
This is a glass drag bit.
It has a diamond in the tip for dragging on glass,
acrylic, and it's spring loaded
so you can set the depth at which it scratches the glass.
And it's really cool.
I made my logo in the router bit cabinet video
as well as BitsBits logo, and it just came out so neat.
This is a vinyl drag bit.
This is for cutting leather, cloth, vinyl on your CNC.
It's really cool.
It's got a spinning little blade in there.
It's a carbide blade.
And it's really cool for cutting cloth.
And this one is really funny.
This is for holding a Sharpie.
So this is a pen plotter tool.
It's also spring loaded and you can use it
to draw on your CNC with a Sharpie
on any material that you want,
maybe making signs that look like they're handmade,
that kind of thing.
So these are some of my more obscure bits,
but again, I've used all of these.
They're really cool.
And I kind of am starting to realize now
I may have a router bit problem.
So let me know down in the comments what you think.
Let me know if you have any more questions
and things you'd like me to cover
in our router bit series.
If you'd like to support the channel,
please head over to the Katz & Moses store.
Pick up a stop block, dovetail jig, or a t-shirt.
Thanks so much for watching, guys.
Stay safe in the shop and have a wonderful day.
