Live Edge Entry Table - A Woodworking How To

House Love
61 followers
12 Video Views·Nov 15, 2022
Live Edge Entry Table - A Woodworking How To
Layla, come here. Hey, what sound does a bear make?
Yeah. All right. We got a fun one today. I had this design in my head for a while,
but really we just sort of flew by the seat of our pants and designed as we went with the only
constraint being the height and width of this window in the entry of my house. So let's jump
into the build. I think you're really going to like this one. All right. So like I said,
we're winging it. I've got this slab that we have just taken out of inventory. And as you can see,
like most woodworkers, I am terrible at using scraps that I save. I try and save less than I
used to, but I always, you know, like all of us, we like, oh, but it's walnut. So we're going to
try and only use scraps today. And my window is about 49, 50 inches long, and I want it to kind
of fit under there perfectly. So we're going to cut a section out of the slab, which actually
just fits in my planer. So we don't have to do a big whole slab flattening thing. But if you do
want to flatten slabs, I have a video right here linked in the corner that walks you through how
to flatten slab. We're going to do what's called skip planing, where we run it through the planer
and just flip it over every time. And we should get pretty flat. I mean, for something like this,
I'm not worried about getting it so dead perfect that you could run a pair of calipers around it,
but we want to get it pretty close. So we're going to clean up this slab and we're going to
find some scraps for the legs. I got a really cool design in my head and I'll show you. I'll
draw it a little bit later. All right. So we've got our slab planed. And like I said before,
we're skip planning. I'm not worrying about it being super parallel and flat. And here's the
benefits and drawbacks. Benefits, super simple, fast. However, it is going to manifest itself
throughout the entire project. So as you can see, I got a little bit of a rock in these two corners.
And knowing that I'm okay with it because I know how to fix it later down the road. And I will show
you how I do that. But the way it's going to manifest itself is we're going to build a frame
for the base. And when it gets attached to the top, it's going to twist the frame a little bit.
So I know that going in and that's why I was okay. Skip planning. But when you do something like this,
that's the reason that parallel and flat are so important is because when you have something
that's off, it's going to continue to manifest itself throughout the rest of the project. So
I know how to deal with it and I'm going to just be okay with it because it's an easy fix on
something of this size. But if I was doing a kitchen table, there's no way that I would do
this because when you have that great of a distance, it's just going to become a much,
much bigger problem down the road. So as far as my base goes, let me show you the design in my head.
So here's kind of the measurements I came up with. What I'm also going to add too, because
we're going to go with like one and a half by one and a half inch legs, maybe one and a quarter. And
so those are going to be really slender. And if you didn't add something down here at the bottom,
they would be really sort of bendy and wobbly. And so what we're actually going to do, we're
going to create like a little shelf, but using sort of the same kind of thing we're doing here,
except we're going to have one skinny guy across in the back and the front like this. And then
instead of like a full shelf, we're just going to do like one shelf in the middle and that'll
really tie it together. It's going to add rigidity and it'll be cool. You can put like a little book
down there, some sort of decoration that'll really tie the room together as they say.
One last thing I want to say about choosing your leg stock is you really want to look for
wood with diagonal lines through it. I believe it's called rift sawn. And the reason is that
you're going to get straight grain on four sides. And when you cut something long and skinny,
ladies, gents, in a square like that, it's going to really have a tendency to twist unless you sort
of pick your grain. So you want to pick grain that sort of runs diagonal across your piece.
Rift sawn wood, it's going to give you a better leg stock. I decided we were just looking at it.
We're going to go with one and an eighth by one and a half inch rectangle legs. And we may thin
out the bottoms a little bit later, but just the very bottom, we'll see if the fun of designing
as you go. So we're going to rip four legs out of the edge of this board, because in here you
start to get plain sawn where you get the middle growth rings. So we're just going to use this
pieces cut, all of our horizontal, our legs, we have our top. We just have to cut those vertical
members that are going to go in between these little guys. Yeah, I have a confession. I had to
go to the lumber store and buy F4S kiln dried lumber, which is so expensive. It's really kind
of an argument for why you should get a joiner. They're super expensive compared to maybe other
tools, but you can buy rough sawn lumber. And I have to drive an hour to get rough sawn. We're
trying to get this video done before Christmas. And so I didn't do it and I paid the price.
And one of the problems with kiln dried lumber is sometimes there's some pressures inside when you
cut them. You know, I took eight quarter lumber and cut it down to one inch squares and it went
wonkier than like John Maleky in a ballet competition because they are like really wild
now and twisted. But we're going to be able to solve that with those vertical members because
we're going to cut dados. It's going to pull everything in. We'll probably thin these out a
little bit more on the planer and figure out our joinery method. Either the domino or I'm going to
use those Miller dowels that I used in the stool build. I think those could be really cool except
we're going to run into some alignment issues where they might be drilling through each other.
Either way, we're going to figure out something cool to do with that. I'm going to cut the dados
in these for those cross members and then we're going to start putting our base together. We'll
I decided to use the domino. We're going to use like the smallest dominoes that they make or at
least that I have. And one thing that's really important, whether you're doing mortise or tenon
or dowels or using the Miller dowel system, you want to label your parts really well. So what I
did here to really help myself is I labeled all my legs in the direction I want to face with which
way is the long way, the short way. I drew a little square. Those are the two sides I'm going to be
using for the joinery where I'm going to be measuring off of those reference faces. I'm
going to go ahead and do all my legs first. We're going to go an inch down and then five inches down
and then four inches up from the bottom to do the crossbars for the shelf, the stretchers for the
shelf. So we're going to go ahead and get that done and then we're going to dry fit it and see
what we're looking like. Make sure everything's all good. We'll cut our shelf and then we'll
secure that and then we'll start our glue up. And what I think I'm going to do on these, we'll
probably put these cross pieces in first. We'll glue those in, let those set up for about 10 minutes
and then glue everything together. That'll give us one last chance if anything goes super wonky.
God, I probably said wonky like a hundred times in this video. Take a shot every time Jonathan
says wonky. All right, let's get into some joinery. All right, now here's a great little trick. We're
going to do these pieces and we need them to be pretty exact because we're doing the small domino
size holes. But here's a great little trick with calipers. I have a great two-minute Tuesday on
calipers as well, which will be linked in the corner. So I measured the width of all my pieces.
They're all the same because they went through the planer at the same time. They're 0.916.
Half of that is 0.458 and this little guy at the end of your calipers is a depth gauge. So you
lock your calipers in right at the halfway mark and then you can just take it to your square.
Boom. And you know that that is exactly 0.458. And then I can use this to mark my dead center
with a pencil and not have to worry about using a marking gauge and leaving a deep groove in there
that I have to sand out later. So I'm gonna finish these up and then we're gonna do a little dry fit.
Well, a lot has happened since that last shot that you saw. I'm sure you probably saw the video where
I hurt my thumb on the jointer. I've used the jointer twice since then and it is terrifying, but
sometimes you just have to face your fears. So we're gonna jump back into this. What happened was
I did all the dominoes for this and stupidly didn't measure. I just assumed because these pieces were
five inches, the dominoes would be five inches apart, but that makes no sense. I don't know why
I didn't think of that. So I have fixed the legs. In the process, I lost about an eighth of my thumb.
I'll link that video right here if you want to go watch it, but one of the biggest things to come
out of that is we are going to be doing a video. We're gonna bring in somebody who's either a
trained trauma surgeon or works in a trauma center to talk about shop accidents, what you should do
if the unthinkable happens. First time I've ever said this in a video, but give me a thumbs up
because I can't do it myself. Glue up time. What we're gonna do, we're gonna do this in steps.
We're gonna do the side pieces first and while those are being glued up, we're gonna glue up the
stretcher assemblies and then we'll let those dry and then we'll put everything together and we'll
put that shelf in last because that way we don't accidentally misalign these two stretchers and
then have the table get all wonky like my thumb. Wonky, that's two shots if you're playing the home
game. Let's get into glue up and then we're gonna get into kind of sanding and shaping this. I'm
gonna do some roundovers, we'll get everything nice and clean and then we'll attach the table top.
All right, we have the base glued up and we just need to attach the top, do a little bit of sanding
and put some finish on it. I'm gonna be using satin lacquer which is one of my favorites to use because
it's really easy to apply, sprays really nicely, dries really fast and looks great. One of the
biggest questions I get when attaching tops is how do you plan for wood movement? Now wood moves
across the width of the board so we are in luck with this piece specifically because it is very
very narrow so it's going to move very very little. I like to sort of as an average give myself some
extra room say that wood's going to move about an eighth of an inch over four feet. It's going to
vary between climates and and types of wood but that is a pretty good rule of thumb especially
that gives me a little bit of leeway because typically you know I think it's more like
eighth over eight feet. So this piece is a foot wide and that means it's going to move a 32nd
between seasons in southern California. So I'm going to drill some oversized mortises. We'll do
floating tenons but one of the easiest ways to do tables is there's these figure eight washers. I'll
put a link down below if I can find them. I wish I had those because it makes it just easy as can be
and is a very secure way to attach top and with no concern for wood movement. So we're going to do
that. I'm going to clamp some boards here. We'll do some magic with the domino. Before I glue the
top I'm going to sand everything and get everything ready to go on the base but you want to do your
joinery before you start doing any sanding. Make sure everything fits because when you start sanding
and altering flat faces it could make it harder to do that joinery later. So let's get this thing
top on and because I didn't take the time to flatten my top this is the consequence but we knew
that going in. So we're going to fix that. Now this is a minor one. You can measure it and basically
you're going to have two high corners and two low corners and so you can measure it's about a 16th
so we want to split that so we want a 30 second. There's a lot of ways to do it. If you're using
felt pads for your feet you could put a 30 second shim underneath your felt pad. That's one way to
do it but here's a great technique that I love. I love these feet. These are I use them for
cutting boards. I'll link them down below. You can buy them in packs of like 120 and what's great
about them is they're compressible at different rates. So what I can do is screw the ones that go
into the low corners less than I screw in the high corners the ones that don't wobble that don't lift
up and down. I can screw them in at different rates giving me about I don't know a 30 second
a 16th worth of adjustment. So I'm going to put these on. These feet will get just barely hand
tightened whereas the the opposite foot on the same side will get tightened a lot and that should
compensate for the wobble. So let's go ahead and put these in. All right so as you can see no more
wobble. There's lots of ways to do this. You can obviously trim the legs. I think I saw Mark
Spagnuolo once do it where he put his table saw blade up a 64th and he passed the high legs over
it because your table saw is flat. Obviously couldn't do it with the table this big. There's
some great ones that screw in and out that are really great for adjusting but you know having
a wobbly table as a furniture maker is just part of the game and you learn ways to overcome it.
Wow guys this came out incredible and it just the way it looks in my house is just incredible.
I love the fact that it fits the width and the height of my window frame which is what's great
about when you design and build your own furniture. There's lots of ways you could do this joinery
with dowels or those miller dowels that I used in the stool build. It came out wonderful. What
would I change? What mistakes did I make? As far as what I would change I would do a lot more
sanding prior to glue up. This took me like four hours to sand today and it was just a nightmare.
So I would have done a lot more sanding. You of course don't want to sand where your joinery
meets up because then you can alter the shape and then you might get some gaps. Other than that I
would sand all these pieces do my roundovers and all that beforehand. The way that we took weight
off the legs it was very a minor amount of stock removal with a major impact. I think it really
looks good the way the legs came out and that was just uh we basically took the corners off at about
I don't know what that angle is a short a shallow angle but we took them off and I used just using
a block plane and then I just made sure not to sand them so you kept those really crisp
sharp edges. The lacquer looks great and I'm really really happy with this. Let me know down
in the comments what you would do differently maybe add some different width shelves uh at
varying distances from each other what you like about it. Happy New Year guys it's the first of
the year. If you want to support the channel head over to the Katzmoses store pick up a dovetail jig
a stop block or an apron. Stay safe in the shop guys. Give me a thumbs up because I can't do it
myself. Have a wonderful day.
