How to repair a1968 Evinrude outboard pull start

The Skill Tutor
20 followers
10 Video Views·Oct 30, 2022
Hello everyone and welcome. In a small fishing boat like we have, you normally have three types
of propulsion. You have the outboard motor, the trailing motor, and a paddle to get you by.
This weekend when we were out fishing, we decided to move from one side of the lake
to the other, and when I went to start the outboard motor, the rope broke on the motor,
and I didn't really think it was that big of a deal because we still had our trailing motor.
After an hour went by, the skies turned gray like it was going to storm, and we started to head back
to the bank. However, the battery on the trailing motor apparently didn't get a full charge on it,
and about 400 yards from the pier, it just quit working all together, didn't have enough juice.
So I got the paddle out and started paddling. Luckily for us, there was a nice family that
came by and we threw our rope to them and they were able to tow us to the pier.
Normally, I keep a toolkit in the boat for just such an emergency, and in the video that I'm
fixing to show of me fixing the pull start rope on this 1968 Fastwing, you'll see how easy it is, and
it is a repair that I could have done on the water. And I kick myself for leaving my toolkit
in the back of my truck because that's prepared lifestyle 101 stuff is always making sure that you
have your repair kits for not just your vehicle, but your boat, your ATVs, and so forth. Now, this
is an 18 horsepower 1968 Fastwing that I'm working on, and all inertia start or pull start outward
motors are basically the same. They just may have a little bit different design to how you get the
assembly off. The only tools you need to change out the pull rope on an inertia start motor or
pull start motor is, of course, the rope. On this Evan route, I'm going to use a quarter-inch drive,
three-eighths inch socket with a quarter-inch breaker bar, vice grips, and a screwdriver,
and these are just to hold the spring-loaded mechanism open as I feed the rope through.
There are just three bolts that hold this mechanism on. There's one here, one right here,
and one right here on the other side. The way that this is designed, you can't fit a
three-eighths drive socket in here, and that's why I'm using the quarter drive.
Once you get those three bolts out, the whole assembly just lifts off.
If you've never changed out the inertia rope on your outboard motor, I would take a file and go
around the inside of this hole because the casting on this leaves sharp edges, and it will cut your
rope real easy. Now that I've got my assembly out, I'm just going to wind the spring inside the
casing. As you're winding, you can look through these holes and see how tight your spring is
compressed. Once I get my spring compressed, I'm going to align my hole where the tag line
that comes out through and the inlet hole is, and then I'm just going to take a pair of vice
grips and clamp it in place. With that done, I'm just going to thread my rope through that hole,
and this is where a piece of wire will come in handy. Take and thread it through that hole.
I'm going to take my wire. I need it to lift the line out. While holding tension on the spring,
I'm going to release my vice grips, and I'm just going to slowly let it go. I'm going to test it
out a couple of times just to make sure it works right. Now we're ready to put it back on the
motor. I'm not going to tighten these down one by one. I'm going to do them all at the same time so
I can make sure that I have space to get my socket back in there in case I ever have to take this
back off. I'm going to put this back in the tool kit that stays in the boat so that if
emergencies arise, we can try to fix them on the water instead of struggling trying to get back to
the bank. And again, I should have been able to do this on the water, but chance favors the prepared,
and this time I wasn't. So make sure that you have your tool kits for your toys. Thank y'all
for watching. We'll see y'all next time.
