This video demonstrates how to fix / adjust / repair the timing of the hook on a sewing machine. If the thread from your needle isn't getting caught by the hook that rotates around, this video explains what to adjust to fix that. Requires some very basic tools and takes 15-30 minutes - maybe less.
Thanks to Nigel Chapman for this helpful comment about the timing: "when you are timing these singer machines there are timing lines on the needle bar to help you get the exact timing required. When the needle bar is at the lowest position you will see two lines: one to mark the lowest point and then the other is used when the needle bar is on its rise. You stop on the second line then adjust the hook to the point where you stopped the needle. Then you should have perfect timing without guessing."Credit: LRN2DIY
Hi, I'm Nils Rasmussen.
I am a cheapskate and my wife's sewing machine is broken here so I called a sewing machine
repair place and they told me it was going to be $90 to fix it.
So I decided to do a little internet research to figure out how to fix it if I could myself
and fortunately as you'll see here, this was just a fix that required some adjustment.
No parts or anything like that.
So the fix we'll be doing today is if you're, the hook, the circle with the hook on it under
here.
I don't know the term so I apologize but if that's not grabbing on to the thread which
is causing the, making the loop so that it actually sews properly.
In my case it's just spinning around, the thread's coming, it's not grabbing on to anything.
So that's what we're going to be fixing today and let's go ahead and get started.
So as you can see I've got a Singer sewing machine here.
This is an older one and I guess that's relative but anyway I've taken some basic tools.
I've got a Phillips, a flat head, a pair of pliers and some Allen wrenches and I've taken
the bottom off of the sewing machine which is pretty easy to do.
Just a couple of screws and loosening a nut and that's all taken apart.
So okay, so here's the underside of the sewing machine and as you can see there's a lot of
gears and mechanisms and such going on here.
So we've got our power terminal down at the bottom or the power block and then here's
the drive shaft I was telling you about.
So it's this silver metal, silver piece right in the middle here that comes along.
And what we're going to be focused on today to fix this is actually, let's get in focus
here, this black bearing, I'm not sure, again I'm not good with terms and stuff like that
but we're going to be working with that.
And as we turn the hand wheel back here you'll see this turning and then it exposes, I've
already loosened this up so that's why it's not turning quite so well.
But you see this little bushing right here or the set screw and that is what we're going
to be loosening to adjust the hook, the hook wheel.
If I rotate the wheel here you can see there's only, in this case there's just one set screw
in there.
I've seen other videos where there are two set screws on this piece.
So just basically what we're trying to do is find the one that has the gear on the end
that controls the turning of that hook wheel over on the back side here.
So what I just did was adjusted this, loosened this and in my case at least it's just on
a number, I just used a, what is this, a two and a half millimeter Allen key here.
So I just loosened that, kind of played around with it and I just happened to get pretty
lucky on the timing of that one where I just tightened it down just to show.
Okay so our goal here and I think I, just in loosening and tightening that set screw
down on the bearing down below or the bushing down below, it looks like I've already got
it started to be fixed.
So as you can see as I'm rotating this down, as soon as it gets down you'll see the hook
enter the picture from the right.
There it is, or there it is, yep.
And you can see it just grabbed on right there and that's what we want.
So if I reverse that out, let's make sure that happens, okay you know what I think I
may have just gotten it and that was just by sheer luck.
So as it's just kind of at it's lowest point that hook should be passing right by it and
then snagging on.
So like I say it looks like we might have it here so I'm going to put this partially
back together and give it a try and we'll see.
Okay I just put it partially back together and I'm kind of shocked and amazed honestly
that with that first attempt it seemed to work.
So as you can see, I just got it on a straight stitch here, I lift this up, look at that,
it actually worked.
So basically that's the, that's what I learned about fixing the timing on the hook wheel
for a sewing machine.
So if you have any questions or comments or anything I'll see what I can do to help, please
feel free to comment.
Thanks.