How To Find e⧸m By J J Thomson Method | Engineering Physics
Welcome all of you. Today our experiment is E by M.
The aim of this experiment is to determine the value of E by M of electron by JJ Thomson method.
This is our setup. Here you can see this is power supply.
We have connected power supply to CRT. This is our cathode ray tube.
We need bar magnet to create magnetic field.
This is our wooden stand.
You can see there are scales on both sides of wooden stand for reading.
This is our magnetic compass box.
The red spot in compass shows the north direction.
This direction is now north and this is now south.
Now let's explain about CRT.
CRT is basically a cathode ray tube.
In cathode ray tube, there is an electron gun which emits electron beam.
There are two circular discs for focus which are placed behind anode.
In the middle, there are deflecting plates which are vertical and horizontal.
At the end, there is a fluorescent screen which is mostly made of zinc sulphide.
When electron beam strikes this fluorescent screen, we can see a green spot.
Let me show you.
We have switched on the power supply.
Electron beam is passing through the cathode ray tube.
When electron beam strikes the fluorescent screen, we can see a green spot.
There is a vertical scale which is in centimeter.
Let's consider the center point as zero.
This is negative vertical direction and this is positive vertical direction.
This is 1 cm, 2 cm in positive direction and this is 1 cm, 2 cm in negative direction.
In the power supply, there is a knob to change the intensity.
You can see that the intensity is changing.
Intensity means the number of electrons in cathode ray tube is increasing and decreasing.
There is a focus button here.
We have to focus so that we can see the sharp spot on the cathode ray tube.
There are vertical and horizontal deflecting plates.
If we apply voltage in the x direction plates, the position of the spot will change in the horizontal direction.
If we apply voltage in the y direction plates, the position of the spot will change in the vertical direction.
The knob is on Y direction.
You can see the vertical shift.
As we increase the voltage, the spot is shifting vertically.
When we increase the voltage in positive direction, the spot is shifting vertically.
When we reduce the voltage in negative direction, the spot shifts vertically.
Similarly, when we shift the nob X axis horizontally the spot is moving horizontally as the voltage increases here.
The spot is going in the positive x direction.
When we were taking the voltage in the negative direction, the spot is going in the negative
x direction.
So, in the starting, what we have to do is that the spot has to be placed in the center
horizontally and we have to try to keep it vertically in the center.
To start the experiment, first of all, we put our compass box in the middle of the wooden
box, which has a scale on both sides.
Now, in the compass, we see that the North-South direction, in this direction, we have to set
the wooden box in such a way that the value of the pointer comes at the exact zero-zero.
So, let's set it a little.
We will have to move the wooden box a little.
By moving it, we have set it in such a way that the value of the pointer is almost zero-zero.
This is North, this is South, this is East and this is West.
Now, what we will do is that we will remove the compass box and we should try to keep
this wooden stand in the same position, not to move it at all.
And instead of the compass box, we will keep this CRT, the cathode ray tube.
We keep the cathode ray tube in such a way that the portion where the tube and diameter
are changing, that portion should be at the center of the scale, in the alignment of the
scale, where the diameter is changing.
The deflecting plates, both vertical and horizontal, are at the center of the CRT.
We have kept the CRT in the North-South direction especially so that the effect of the magnetic
field on the earth is minimized on the CRT, that is, on the electron beam.
The effect of the magnetic field on the electron beam should be minimized.
That is why we keep the CRT especially in the North-South direction.
Now, let's note a reading as a sample and show it.
Like here, I turned on the power supply.
At this time, we have not applied any voltage to the power supply.
So, the electron beam will travel completely straight.
So, we have to note its initial position, which you can see here.
To remove the parallax error, we have to see it from the front.
So, it is almost 0.2 cm in the upper side.
If we consider the point in the center of the graph as the origin, then it is almost 0.2
cm in the positive Y direction.
So, this is our zero error.
This is our initial reading.
Let's note it.
The initial position of the spot is 0.2 cm.
Now, we will apply voltage here.
How much voltage do we apply?
We apply 20 V in the starting.
I am showing you this reading as an example.
We applied 20 V here.
You can see that the position of the spot has changed.
Now, the spot is in the negative Y direction, which is 2 cm.
This was our center.
It moved 1 cm and then moved 2 cm.
The initial position of the spot was 0.2 in the upper Y direction.
The final position of the spot is 2 cm.
So, the deflection is 2.2 cm.
Now, the deflection has moved 2 cm in the lower Y direction.
The initial position of the spot was 0.2 in the upper Y direction.
So, the deflection is 2.2 cm.
How much voltage did we apply?
We applied 20 V.
Now, what we have to do?
Why did it move here?
We applied voltage on the vertical plates.
An electric field was created there.
Due to the electric field, a force was applied on the electron beam.
When a moving electron passes through an electric field, a force is generated.
Due to that force, the electron beam moved.
This is why the deflection has been shown.
Now, we will create a magnetic field through these bar magnets.
We will create a magnetic field through these bar magnets.
The force applied on the electron beam will be equal to the force applied on the electric field.
How will we know that?
When we use both the attractive poles of the magnets,
we will place one magnet on this side and the other on this side.
We have to simultaneously move these poles to see when the spot returns to its initial position.
The initial position is 0.2 cm from the upper side.
Let's set that.
You can see that the spot has returned to its initial position.
The spot is now in the same position as it was when there was no electric field.
Due to the electric field, the force applied on the electron beam is eq.
Due to the magnetic field, the force applied on the electron beam is bqb.
Since both the poles are equal and opposite, the spot has returned to its initial position.
We have to use the attractive poles of the magnets every time.
You can see that the value of this pole is 10.5678.
This is 10.8 and this is 11.
Let's note both the readings.
10.8 and 11.
Let's note the scale of A pole and B pole.
10.8 cm and 11 cm.
If this pole is the north pole, then this pole is the south pole.
If this pole is the south pole, then this pole is the north pole.
Now, we have to find θ1 and θ2.
How do we do that?
We have to remove the CRT.
We don't have to change the position of the magnets or the position of the wooden box.
We just have to remove the CRT.
We will remove the CRT.
After that, we will place the compact box here.
In the compact box, we will see which two angles are being shown by the pointer.
Those are θ1 and θ2.
You can see that when we place the compact box here,
this reading is being shown.
θ1 is showing around 71 and θ2 is showing around 74.
We can consider any of the pointers as θ1 and θ2.
It doesn't matter.
One reading is θ1 is 71 and the other is 74.
We will note these readings here.
θ1 is 71 and θ2 is 74.
The voltage is 20V.
Now, we have a reading in which the positive voltage is shown.
In the vertical deflecting plates, one plate is positive and the other is negative.
This reading is due to the electric field.
Now, we can reverse this reading.
If we take this 20V in the reverse direction,
if we take it to the negative 20V,
we will get one more reading.
To make the answer more accurate, we can use this calculation.
Now, we have made the voltage negative.
The vertical deflecting plate which was positive is now negative.
The previous negative plate is now positive.
Again, we will note the position of the spot on the CRT.
Obviously, the initial position of the spot was at 0V which is 0.2cm in the upper right direction.
It will remain the same.
We just have to note the final position of the spot.
Let's see the final position here.
As you can see here,
this is our center.
This is 1cm, this is 2cm.
This is 2.2cm.
2.2cm is our final position.
The initial position was 0.2cm.
So, the reading in the negative Y direction will be
that the deflection will be only 2cm.
This will be our negative field.
Now, we will see the C and D poles.
Again, we will use magnets.
We will use magnets to find out the initial position of the spot.
So, we will use the opposite poles of the magnets which we used last time.
Since the direction of the electric field has changed,
obviously, the direction of the magnetic field will also change.
So, we will use magnets to find out the initial position of the spot.
The initial position is 0.2cm.
We have to move the magnets simultaneously.
As you can see here,
the spot is almost at its initial position, 0.2cm.
The reading of the magnets is
1 is 13.7
and 1 is 10.8, 9.
13.7 and 10.9.
So, we will note this reading here.
13.7 and 10.9.
Again, we will remove the CRT
and we will put the compass box here
and see how much is theta 3 and theta 4.
Here, you can clearly see that the readings of the compass box are
theta 1 is 72
and theta 3 is 72
and theta 4 is 73
or 74.
72 and 74.
So, we will note these readings for theta 3 and theta 4.
theta 3 is 72
and theta 4 is 74.
We will note these readings here.
Wherever we have calculated on the paper,
theta 3 is 72
and theta 4 is 74.
Now, we have taken the readings.
Now, we have to do the calculation.
For the calculation, we will need the mean of these thetas.
Through that mean, we will create the value of the magnetic field
which we had created for the bar magnets.
Here, you can see
the observations that we have got.
The CRT constants that we get from the manufacturer are
the length of the horizontal pair of plates is 30 mm
i.e. the length of the deflecting plates is 30 mm.
The distance of the screen from the edges of the plate
i.e. the distance of the screen from the edges of the deflecting plates is 85 mm.
The distance of the screen from the edges of the deflecting plates is 10 mm.
These are the CRT constants that are given by the manufacturer.
We have noted the readings here.
Now, we have to find the magnetic field.
How will we find the magnetic field?
The four angles that we have got are
theta 1, theta 2, theta 3 and theta 4.
Theta 1 and theta 2 were for the positive voltage.
Theta 3 and theta 4 were for the negative voltage.
We have used the 20 voltage both times.
Once for the positive and once for the negative.
So, this is the mean of theta, 72.75.
The horizontal component of the magnetic field of the earth is 0.32 Gauss.
To find the magnetic field, we will use the formula
h is equal to he tan theta
where he is the horizontal component of the magnetic field of the earth
whose value is 0.32 Gauss tan
and we will use theta.
tangent of theta.
Let us calculate the value of the magnetic field that we have created.
tan of 72.75
which is equal to 3.22 into 0.32
This value is 1.03
The magnetic field that we have created here is 1.03 Gauss.
We are not using CGS here.
So, we have created this much of Gauss magnetic field here.
Now, let us see the formula to find E by M.
The formula is
voltage into the deflection that we have got
into upon
small l
l is the constant of the cathode ray tube
and h is its value.
We have applied the voltage of 20 V.
What was the deflection that we have got?
The deflection that we have got
in positive 20 V is 2.2
and in negative 20 V is 2 cm.
So, the mean of these two is 2.1 cm.
Here, we are using all the units in series.
This is 2.1 cm.
This small l, capital L, D is the constant of the cathode ray tube.
The length of the horizontal pair of plates is 30 mm.
So, we will convert this into cm, which is 3 cm.
Distance of the screen from edges is 85 mm, which is 8.5 cm.
Separation between the plates is 10 mm, which is 1 cm.
We will note these values here.
The value of h that we have calculated is 1.03.
The square of 1.03.
Let us calculate this value and see how much it is.
This is the value of E by m.
The value that we have calculated is 1.55.
I have shown this reading as an example for 20 V.
Similarly, we can take readings of 30 V, 40 V, 25 V, 35 V.
We can take three to four readings
in respect of positive and negative voltage.
The more answers we get, the more accurate our final result will be.
The result that we have calculated is 1.55.
The standard value is 1.756.
We can calculate the percentage error here.
The formula for the percentage error is shown here.
The percentage error is 11.7%.
I have shown this as an example for one reading.
Similarly, when we take three to four readings,
we can get more accurate answers.
In this way, we can find out the value of E by m using Thomson method.
Thank you.

