Howdy folks! Welcome back to Nomad Boat Building. My name is Mark Reuten, and we're picking up where we left off on the Poulsbo Boat Project.
The inwales and thwart risers are glued up, but there's one more piece to fit before we can fair everything and get on with planking. The shape of the transom means I need to add extra material to one inwale, and that calls for some careful tapering and compound bevels.
In this episode, I work through the fit, demonstrate my technique for cutting compound bevels by hand, and make a quick mockup to test how much material I can remove before shaping the real piece. A little experimentation up front can save a lot of awkward work on the boat.
I also fit and glue the final filler piece using thickened epoxy and polymer nails. With the inwales and thwart risers complete, we're getting closer to fairing the structure and starting the cedar-strip planking.
The original Poulsbo boat was a sport fishing boat built by Roland Young in Washington using traditional carvel plank construction. This version is being built with cedar-strip construction and fibreglass inside and out.
Chapters are listed below. Thanks for watching, and I'll see you in the next episode!
0:00 Why a quick mockup is worth doing 0:21 The Poulsbo Boat Project 0:39 Adding the final inwale filler 3:15 Testing the fit and bend 5:00 Marking and cutting the bevels 7:04 How to cut compound bevels by hand 10:35 Marking the taper for the bandsaw 11:49 Making a mockup before cutting the real part 14:01 Working through the test cuts 16:06 When everything seems to fight you 17:25 Checking the mockup and refining the cut 19:00 Why the mockup saves time and effort 20:16 Shaping the taper with a power planer 21:04 Supporting the channel 22:14 Gluing in the filler piece 22:42 Splitting the filler to make it bend 23:31 Using polymer nails to tack the piece 25:45 Checking the fit 25:56 Inwales and thwart risers complete
AI Generated·May contain errors
Video Summary
AI Generated
This video demonstrates the installation and fitting of inwales and thwart risers for a Poulsbo sport fishing boat. The builder focuses on overcoming fitment challenges caused by the boat's tumblehome at the transom, utilizing mock-ups to minimize waste and employing a specialized manual compound bevel cutting technique to ensure precision before moving toward the planking stage.
Sometimes, you know, stuff just takes a whole lot of experimentation.
You know what you do if you're curious about something like that?
What you do is you get another piece of stock
and you do a quick mock-up.
Throw it onto the boat and see if it looks correct.
I think I should do that. I think that's worthwhile.
Hey folks, welcome to Nomad Boat Building.
We're picking up where we left off on the Poulsbo boat project.
The Poulsbo boat was a popular sport fishing boat built
by Ronald Young in the Poulsbo, Washington area.
Ronald built his using traditional Carvel planked construction.
We're building ours using a modern cedar strip construction,
fiberglassed inside and out.
Hey, good morning.
It's problem solving day.
Well, not big problems.
So yesterday we got our inwales and our thwart risers installed.
So they're all glued up, glue's cured.
Now I've added some little angle brackets to hold it in place
because there's spots, especially in the midships,
because this boat's got sort of a flat sides
that they're gonna they would be springing out if i
didn't pull those in so brackets on the inside there
these are gonna get painted so i'm gonna
can fill those holes no problem down here brackets on the bottom
because these are probably gonna
get bright finished on the inside
and so i want those clean there's gonna be a pile of fairing
off to do up at the bow they are captured against the face of the stem
and i've added some little
bits of plastic like just some fast food packaging
to keep from bonding to the stem
and then back at the transom
so the thing i need to do is add one more layer of material to the
inwales because the um the amount of tumble home
on the transom here we got about three quarters
of an inch more material that i need to have onto
these inwales in order to fill out this corner
and that's going to come all the way back
to about about there about midships i don't need
to do it on this guy because i've already built
in the uh the extra on the on the bottom corner
but on this on this one i wanted the top corner
to be a consistent width all the way along but
that means that i needed to add more
to the bottom side likewise back here the top is going to be a
consistent width, all the material is going to come off
this bottom side. So it's kind of the opposite.
That's the wind that's in the in-whale.
So I got a piece of fur here
to do that little filler bit with. I'll see...
I'm not sure if I'm gonna be able to just bend it in place
the way it is, or if I have to steam it.
And the other question I have is whether or not I should
bevel it, or like taper it now,
and then glue it in in the tapered state.
Or at least I think I'll probably do that.
maybe not taper it all the way,
but like get it down to within a quarter inch of the finished
thickness, and that will go a long way to getting this job done faster.
I suppose I could bevel it
too, to do that on the table, on the bandsaw maybe.
I hadn't thought about that, but I could think
about that. That's the plan,
so I think I'll just start by just chopping this to length and then
see how it fits 72 yeah something like
that yeah 72 inches ought
to be about right maybe we'll go
like 75 or something like that or 76 just
to be safe let's just start
by just shoving it into
place for that that's like an inch
and a half that it's got to swing up in the middle let's
just see what happens if i try
and put the squeeze
on it much for that i hope
this is going to work
at all.
Sometimes, you know,
stuff just takes
a whole lot
of experimentation.
I'm waiting for the
spring, the quick grip that's holding it at this end to just pop free.
Maybe not. Okay, that sort
of works. Okay, I think I should put the bevel
on that end, mark the taper onto here, leaving it a
little heavy, at the very least a little heavy
on the on the feather edge. And you know what we're
going to do? We're going to start,
we're going to start with just taking a bevel. That I can do.
bevel that way, bevel that way. That's step one.
I have on the back end here all things considered.
All right, and I don't think I need
to worry about it being 100% in place to mark my lines on it.
Make sure
it's clamped
on here properly.
We'll just
project down
roughly there.
I have a feeling
that if I reduce this down, I might be able
to bend it up into place easily enough. Sometimes
that works and sometimes it doesn't.
Bending skinny things on edge can be challenging.
So we've got there,
there, bevel, bevel.
So all through
the process of making
these in-wales,
I've been having to do these compound bevels
on the ends of the in-wales. Right, so we've got
an angle that way, got an angle that way,
and of course the angles that way, and the angles this
way. So setting these up on a miter saw
to cut is not worth the effort. Cutting
them by hand is really simple
when you get as a very specific technique down
and it's not a difficult technique.
So I've shown this before but it's worth
showing again because
who knows what video I showed it to you before. So
let's just do that again right now.
I'm gonna move the camera to where you can
see me cutting and just follow along.
The trick here is to look at the lines
you've drawn onto your stock
and what I think you should have is a line drawn on the top edge
and then both broad faces. And don't worry too much about
the bottom edge because it's not really
that important. And so where you want to start
is on the edge where both angles are kind of going
in the same general direction.
So this one's going to the right a little bit, this one's going to the
right a little bit, as opposed to the opposite
in which this one's going to the right and then
that one's going to the left. so i would call that an acute angle
and i would call this one
an obtuse angle. so the obtuse angle is a little easier
to work with. just visually easier. it's
the same angle. so we start on this obtuse corner
and before we go more than a couple strokes we
want to correct our angles. so we want to make sure
that the saw is following the long face
and the short face at the same time. and so within
the first few strokes you're just looking to make
sure that that is tracking the way you want it
to and then what i suggest is you start to start
rolling away okay once your saw
passes the bottom corner i think
it's a good idea to start rotating
let the saw follow the path that you've already created now
and before you go off the bottom i
want you to rotate up once you cross that outboard
corner you can come back around and push out
and in an ideal world you actually ring the whole joint
but because this is clamped in the vice and
And they've got the cameras in the way, I can't do that easily.
So by wringing the whole joint, you avoid breakout.
With a little bit of practice,
these freehand compound cuts will become second nature to you.
And if you find you're straying off the mark a little bit,
start on another corner and try and correct it.
And you can join up with your first cut in the middle.
And a little bit of cleanup with a block plane is no big deal.
I never use my miter saw for compound angles at all.
I only ever use it for a single bevel in any one direction.
Okay, now I want to mark a line
on top to follow with the saw.
So I think I'm just going to go outside corner to my marks.
And they all look like they line up pretty good.
I'm sure I'm staying outboard of them a little bit.
I think I'm safe to go ahead and cut that on the bandsaw.
So this is where my station is, roughly.
I could probably even connect the dots of my lower cut.
like that guy basically can swing down
to like here i'll bet you i could chop that away
but i really wanted to but that's kind of risky
and if i can chop that away that means i could
take this one the same spot which is about there
and chop that away i'm trying to visualize exactly
how much material i can remove at the bench instead of on the mold
or it's way more difficult
i don't know if that's a good idea
or not you know what you do if you're if you're curious about
something like that. What you do is you get another piece
of stock that you don't care about
and you do a quick mock-up.
So you just try cutting the thing you think is correct into some
junky stuff, throw it onto the boat and see if it looks correct.
I think I should do that. I think
that's worthwhile because that'll save me a whole lot
of wasting wood away in a very tedious manner.
So
let's
do
that
the
butt
end
now.
We're
gonna
take
guy
There that's down
this guy we come
to you there
There
look
at that on
this side
there
I'm not even sure how I'm
gonna cut these exactly
so that's a big corner
that disappears
the rest is just a taper
Oh, but that corner might be affected by this taper.
I got to do the taper first
Okay, to the
bandsaw.
This thing
is wildly
out of
square,
screwing
me up. This
doesn't need
to be neat,
that's the key. Just needs to prove our point.
So that'll go to that, yes. This side, that point
goes to roughly that point. I don't know
if I can cut that on the bandsaw or not,
because it'll be
a winding bevel. Oh, just our keeper side.
This is our keeper, the rest is garbage. Okay, I have no
idea what I'm gonna
do is gonna work I'm just gonna
try it I feel like you got
one of those days where every stupid thing you try is being impeded by
something it's a Friday that's what it is it's a Friday
and I already know I
got to go somewhere at lunch
which is basically gonna murder whatever I had
plans I had
for the rest
of the day and
that's all very
frustrating
that's so
good so my goal
here was just
to see if I could
figure out how
much waste I
get rid of without compromising
the eventual shaping I need to do.
So that's there. This will
have to get sewn up into place here.
That looks like that's going to work okay. Works good there.
Anything.
This bevel actually needs
to travel through here.
So we zero out on the bottom there.
So that works okay. If anything, I could probably
do more shaping off the mold to bring it a little
closer, though it's probably not worth it, yeah yeah
do the taper, that's fine, waste away that corner
because that just saves me a whole lot
of meat I gotta pull off, although there's still a lot of meat
here, so I could fair that all the way through
to nothing back here, go nothing all the way through
actually, so I could probably do that, the power planer, okay that works
so that represents you
know, a great example of how doing a mock-up
of a part can really save you a lot of effort
Now it took a few minutes to head scratch my way through that mock-up,
but if I had just thrown in
the solid stock, I know I would be putting a whole lot
of effort into trying to work the bevels into
this all the way through here in place,
which can be super awkward, especially because they got the
transom that stops me from being able to take
a plane all the way through that way. So this sort
sort of gives me a dry run
and I have a pretty clear idea of what I can get away with in terms
of getting this new piece of stock down to not a finished shape obviously
but kind of a bare minimum.
So back here on my part this is the keep part.
Keep my orientations right.
So we do our taper
first and then we can do our bevel
we have to remark that bevel
but then what I can do is I can
take this and I can wind it all the way down, actually quite
a bit further, I can wind it all
the way down towards the to the tail end if I want
to and save myself a whole bunch of planing
so I think I'll do that, the time spent
on the mock-up just increases your confidence that the
finished part is going to come out right
and you can move ahead at twice the speed easily
so I decided to just wind this bevel down using
the power plane the whole way and not try and
cut it on the bandsaw which was awkward at best.
If you're liking these videos you can support me
by giving me a thumbs up, throwing me a couple of bucks
or super thanks, subscribing to the channel,
turning on notifications,
and of course you can join me over on Patreon. Find links in the corner
or down
in the
description.
Okay
let's get
this guy
gooped
together.
So I wet
out the
other
side
and I'm just doing a sloppier wetter thickened epoxy batch
for this side. It didn't take forever
getting this on so i ended up splitting this um
little filler piece i left it solid up to about
there and then i split the rest of it down the middle
because it wasn't going to take the um
the bend it's like it's amazing how a little thin thing can
be so stiff on edge and yet if you like
triple it in thickness or quadruple it it suddenly it bends no problem
but it's just a little skinny
bit it's like it's
impossible crazy
the way that works i'm
using polymer nails
in this
brad nailer here basically plastic nails works really great
for tacking things together they
don't have a ton of holding power on their own
though but you can plane through them without
messing
up
your
blade
too
much
they're
a
little
bit
a
little
bit
abrasive
on it
okay
i
think
using it all the way along the other side all right folks now
that that little filler piece is in
our inwales and thwart risers are complete
and they are ready for fairing we'll take care of that
the next episode then we can actually get on to planking.
And I know in the last few episodes
it seemed like we were ready for planking almost and then again almost.
Well this time after we
get these faired off we actually are ready for planking.
So please join me again for the next
episode and I want to thank you all for watching
and I especially want to thank my followers on
Patreon whose support makes these videos possible.
So if you'd like to help support the channel
please consider joining me over on Patreon.
You can find links in the corner or down in
in the description. Hey, if this is your first time joining us,
maybe you want to go back and watch
our previous episodes and put the playlist down here.
Alright folks, until next time, we'll see you later.