This guide details the professional process of transforming a Morgan Dollar into a wearable coin ring. It covers the technical journey from initial cutting and annealing to advanced shaping techniques like Swedish wrapping, concluding with antiquing and a strategic approach to building a specialized tool kit.
In this third video of the series making coin rings with a basic quality tool kit,
we're going to be going over the larger coins, which is the Morgan Dollars.
And just like the other videos, we are not investing yet in a really awesome auto punch
kit like this, but this would be the very first thing I buy
once I start buying nice tools that are unnecessary.
Since it is unnecessary, we're going to mark this thing out and cut it with a jeweler's saw.
So what we're going to do is stack up some stuff, whatever it's going to be,
put the coin next to it, get our sharpie, and then start to a nice even circle.
Okay, so we're going to cut that out now.
And just like before, we're going to punch a divot with any kind of punch you might have.
Mine happens to be an auto punch.
And then drill a hole with whatever kind of drill you might have.
Mine happens to be a Fordham flex shaft.
We're just trying to get a pilot hole so we can start our cutting with our jeweler's saw.
Here's our jeweler's saw.
And interestingly enough, this is the exact same blade I've used for all three videos.
So hopefully it stays good.
But this is a cheap jeweler's saw.
Just to quickly recap, it's under $10.
And these are 3-0 blades.
They're nano blades.
All this will be in the description box, though.
All these tools will be.
And they come in a 12-pack for six bucks.
All right, nice and tight.
Put a little lube on it.
Any kind of lube will work.
Mine's Pepe lube.
You get this from the same place you get the blades.
But you don't need it.
You can just use oil if you wanted to.
I've always used Pepe lube.
I like it.
But it's definitely not expensive either.
I mean, if you're ordering the blades, you might as well just order the Pepe lube, I suppose.
But you don't have to use it.
So there's that.
To be honest with you, I'm not really happy how small that hole is.
So you can do a couple different things.
If it's just slightly too small, re-mark it again.
And then you could file your way up to it, which would take a while.
But it would also make it perfectly more round.
If there's any issues with it being not perfectly round, that's the way to do it.
Or mark it wider again and just cut around again if you want to go a little bit bigger.
I do.
This hole's a little bit too small, so I'm going to cut it again.
All right, that's a little bit wider, this one.
Now what we're going to do is get rid of any of these sharp edges with our half round file.
And like I said before, you can get kits of these at Harbor Freight.
They're extremely cheap and very useful.
I use files all the time for all kinds of stuff.
This is a good example of one way to do it.
But what we're going to be doing is cutting this 45 degree angle with our file.
And what we're trying to do is avoid this splitting when we start to stretch it.
So any sharp angles will lead to a split.
So we're going to just take our time and get rid of any of these sharp angles.
So now what we're going to be doing is softening the metal.
It's called annealing.
And we're going to be using our torch that we purchased from our last video to anneal it.
We're going to bring this up to a very dull red.
If you're in a dark room, a nice dull red is what we're looking for.
We're in a pretty bright room right now, so it's going to be a little hard to see.
But you don't want to go bright red.
It'd be too far for silver and you'd run the risk of melting your coin,
which we definitely don't want.
So just slowly.
And notice how the flame is not a really aggressive flame.
It's a pretty soft, low flame.
You want it to be really soft, not aggressive,
and slowly bring it up to temperature.
You don't want to speed this step up.
We're going to grab it.
And just another quick note.
With non-ferrous metals like silver, gold, copper,
you can quench it without hardening it like you would a ferrous metal like steel, iron.
All right, that's nice and annealed.
Try it off real quick.
And we're going to start folding it.
And like I said before, this is the Pepe Tools ring stretcher.
This is the cornerstone of all coin ring making.
We bought this in our first video.
The most expensive tool we purchased.
Now the problem here is this will not fit in our coin ring die.
It's just too big.
So we're going to have to buy this guy.
This is one of the tools we're buying for this video.
The 1.5 to 1.6 17 degree die from Jason's Works.
This will be a link in the description box below.
We're going to be using it in place of this.
So we'll put it down here.
And we're going to be doing a tail side out ring.
So we're going to put a head side facing up.
And we will start like we did before with our steel starter cone.
Once it's started like that, we can switch to our composite cones,
which will make sure that our detail doesn't get damaged in any way.
It's a lot softer than a steel cone, obviously.
We'll keep pressing.
Okay, now we've got it about this far.
And what we're going to do is re-anneal, re-soften the metal.
And that's going to make sure that we're not going to get any splitting
as we start stretching that even farther.
Keep it going, same die.
We're going to go up to the next size up folding cone.
Make sure this thing's pretty level in there.
Keep folding.
The next size up now.
We've run out of room with that.
So the next thing we have is this little guy.
It comes in that kit of folding cones.
This will allow you to go a little bit farther down the die.
All right, now it is stopped.
You can see that allowed us to close this thing completely up on their folding cones.
So you don't want to have any gaps in there.
That's when you know you're done folding.
So take that off, re-anneal it, and start Swedish wrapping.
The next tool we're going to be needing is something else we're going to need to purchase
for the Morgan Dollars, which is this guy.
It's a Jason's Work Swedish Wrap.
And it's a 1 by 1.4 inch.
So 1.4 on one side, 1 inch on the other.
And it also comes with these guys.
These are your push followers.
One thing I'm going to splurge on though in this video is introduce this.
This is a Ross push follower.
This is like 67 bucks on the website.
You can get them in kits.
You can do smaller ones that we've done in previous videos too.
I have all of them.
I use all of them all the time.
But it's unnecessary.
You can use these.
This just makes it way easier.
So I'm going to factor in the $60, or nearly $70 for this guy.
It sounds a little bit ridiculous, but it makes life so much easier.
So we're going to use that.
First step to Swedish wrapping is wrap this guy in Teflon tape.
And the reason why we're doing that is because right now we have to stretch this thing in
order to make it even until our ring stretcher touches everywhere on the inside of this.
And if we were to do that, this thing would make like a size 17 ring.
So in order to make something smaller, this one I'm shooting for a size 13 today,
we're going to have to shrink this overall size.
And we do that by pushing it down this really narrow die, the Swedish wrap die.
And in order to not damage the detail on the outside, we're going to wrap it with
Teflon tape, 25 wraps to be exact.
All right, that is nice and protected.
This is our one ton Arbor press that we've got at Harbor Freight from our last video.
We're going to use it here again.
We will put our Swedish wrap die on here.
Fit this coin in.
Coin edge facing up.
And then we're going to start with this biggest brass push follower.
The reason we're using this one to begin with is if you were to start with this,
it's got a bit of a gap.
It's a little sloppy in there and we don't want to damage these.
These are kind of easy to damage.
So we want to make sure it's completely supported by the walls of this die,
which means we'll push it down to begin with with this brass push follower.
I always start with brass.
It doesn't go very far.
It doesn't have to.
And the cool thing about that is it'll cut the top off of our coin.
So we get all that Teflon off the top.
This isn't going to damage the top of this coin if we do it correctly.
And the Teflon will make it to where this can slide into the slide unnecessarily.
So we cut that off the top.
That's actually going to protect our push follower.
So now what we're going to do is we're going to press,
turn the die itself and turn the push follower a little bit.
We don't want this push follower to continue going down in the same spot on the coin.
It'll create a little line where this gap is.
So we're turning that.
We're also turning this because our one ton arbor press is not totally plumb.
So that'll counteract that if we just keep spinning it.
And we're going to keep doing that as we go down.
That will be about it there.
So now what we'll do is push it out of our die.
And now it has shrank down considerably from what it was.
Pull the Teflon tape off.
And we've moved the metal again.
So we're going to re-anneal.
Basically every time I move the metal, every time I complete a step,
I'm going to re-anneal.
Just to make sure it's soft for the next step.
All right, soft and ready to go.
Now what we need to do is stretch it on our ring stretcher.
And I always like to start with the trash bag between the coin and the ring stretcher
just to make sure the detail stays nice.
And with Morgan Dollar coin rings, we need to stretch it two and a half sizes larger
than our target size.
Notice I'm stretching it coin edge facing up.
I'm always going to stretch it this way on a ring stretcher.
So we need to go two and a half sizes larger than our target,
which means this has to be a 15 and a half if we're making a size 13.
And also this has to be touching the ring mandrel the entire way.
You can't...
It has to stretch at least as big as to get this touching this everywhere.
And if you can't, you need to go back and swish wrap it down farther if it's still too big.
So we want this to be 15 and a half.
All right, that should do it.
15 and a half.
Perfect.
And we always measure the ring size on the coin edge side.
That's the only side that matters on a coin ring.
And so we did move the metal, but we're coming to the end of our ring
and we want to make sure that the silver is hard.
So we're not going to re-anneal at this point.
We're going to keep the hardness on it.
Put our regular coin ring die back in with a 17 degree die facing upward.
And we're going to size it down to a size below our target size in a 17 degree die.
We're just a little bit under 12.
That'll be okay though.
It's close enough.
Now we have it like this.
We're going to switch to our 25 degree die side now.
But it starts to get pretty hard to push something this thick with our coin,
with our ring stretcher.
So we're going to have to buy another tool, which is going to be this guy.
This is a six ton A-frame press.
I got this at Harbor Freight.
I found out that they no longer sell these at Harbor Freight.
I think they only do like a 12 ton and a 20 ton.
Vevor makes one also.
It's a six ton H-frame.
This guy right here.
I'll put that in the description box below also.
But for us, we're going to be using this one since I have it.
Now what we need to do is take our coin ring die that we have from our ring stretcher.
Put it to the 25 degree side.
Put our coin ring with the coin edge facing down still.
And this is another tool we're going to need to get.
It's a coin ring anvil from Jason's Works.
So I will add that in the description box as well.
Put that in.
And now we're going to press this thing down another size below our target size
to make it a total of two sizes below our target size.
So we're shooting for a 13.
This is going to bring it down to an 11.
Make sure it's nice and even.
We have a taper going the other way.
And so what we're going to do is turn it this way now
and make both sides match on the outside.
So now our shape is correct.
We're two sizes below our target size.
And the reason we went so far below our target size is because this rim,
it's really sharp and it's really big.
As a matter of fact, it's about two sizes to remove to get it to flatten out.
So that's what we're going to do now.
We're going to go back to our bench and file that out until we hit 13 again.
That'll make it nice and flat, smooth and comfortable to wear.
That all filed.
We're going to sand it with a little 220 grit sandpaper
to get rid of any file marks that we might have.
And also I filed this side too.
I always file a little bit on this side to make sure it's not sharp.
We'll sand that as well.
Sand the outside as well just to clean it up.
It should be about a 13 now that that's all removed.
Let's see where we're at.
13.
Try on the bunny.
13.
All right, let's clean it up and get it finished.
Okay, this is our jeweler's pickle.
It's called Smart Pickle.
And we've got it in water.
It's heated up to just below boiling.
And we're going to throw our coin in there.
What that's going to do, it's going to clean anything off of it,
any oils on the surface and bring it back to nice, clean, raw silver.
And we leave it in there basically just long enough to do that.
Just long enough to heat up some water we're going to use for our antiquing process.
So this is the cup we use, that I use, for our antiquing.
Put just a little bit of water at the bottom,
maybe like an inch, inch and a half of water at the bottom.
Just enough to cover the coin really.
That's all you really need.
And I heat that up in the microwave for about a minute and a half.
By the time I'm done with that, I'll have this out and cleaned.
Our water is now microwaving.
We're going to pull this guy out of there.
Don't use anything steel to pull out of a pickle or a little copper plate.
So you can use, I have a straw I've been using for years,
or these copper tongs, whatever works.
Just pick it out of there, rinse it off.
And making sure you don't touch it,
get a nice, clean paper towel and just wipe it down.
Get anything off the surface and get it ready to antique.
We just don't want to introduce any oils from our fingers or anything else.
All right, that is clean and ready for our water when it gets done microwaving.
All right, that is fresh out of the microwave.
We'll add a couple drops of our liver of sulfur XL gel.
And this is going to be our antiquing solution.
Give it a couple swirls, make sure it's good and mixed.
Drop in our ring.
We'll leave that in there for about a minute.
All right, it's been there for about a minute.
We're going to go ahead and pull it out of there.
Rinse it off again and dry it off.
And what you should be left with is a really even dark coating on it.
That looks great.
So if you didn't get all the oils off well, you'd have splotchiness
and that's really unfortunate.
You want to get this right the very first try.
It's kind of hard to make it even coat once you've done this step wrong.
Now we'll take our 4-0 steel wool and we're going to lightly, extremely lightly,
start to remove some of that darkening from the high spots.
And how much you take off is really up to you.
This is about perfect.
That's about what I'm looking for though.
And I'll clean off the cut side that we cut.
Make it look nice.
Clean off the coin edge on the outside.
Make that look nice.
And then really lightly take off the highlights from the outside.
And that is about perfect.
From here you take Carnosaur's Jewelry Wipes.
And like I said before, all of our supplies and tools
are going to be in the description box below.
And give this a final polishing.
You are now able to make Morgan dollar coin rings.
We only had to buy a couple hundred dollars more tools from the kit we already had.
The original kit was the most expensive kit to make the quarter coin rings
because the biggest tool in there was the ring stretcher.
But once we started that kit, it was under $600.
You make five or six quarter coin rings, you pay for that kit.
Then you add a couple hundred dollars more tools
so you can make half dollar size coin rings.
Once you've done that, you add another.
This is the bigger expense of the kit was the Morgan dollar kit.
Another $350, maybe $400 worth of tools.
You can make basically every U.S. coin from top to bottom.
Or any other coin in the world for that matter.
That is how I build my kit.
And you could pay for this section of kit by making a couple Morgan dollar coin rings.
And that's how I would build my kit slowly from start to finish.
All right, thanks for watching.
I'll catch you on the next one.