This tutorial demonstrates the professional process of transforming a silver half-dollar coin into a high-quality ring. It covers essential techniques including precise cutting, annealing for malleability, and the use of specialized dies and presses to shape and size the metal, concluding with an antiquing process to highlight the coin's intricate details.
Hey, Skyler here from Change You Can Wear and Sojourn Fine Jewelry.
Last week we made a video on how to make quarter coin rings with a basic kit.
Good tools, but really basic.
In this video we're going to add two tools that will allow us to make half dollar size coins into rings.
And if you want to see that first video, check the description of this video.
I'll add a link to it there.
All right, let's get started.
So here's what we're going to be using.
A silver half dollar.
These came from a special mint set that did silver.
After 1964.
So 92 and later they made special mint sets that had silver.
More you know.
And so what we're going to do again is take a sharpie.
This is a micron actually.
It's not quite a sharpie, but it's going to give us a little bit finer detail.
That one may go up in size a little bit.
Let's keep going here.
The key is to find the right thickness that you want
in order to get the circle that you want to get.
So we're marking out what we're going to be cutting out.
That looks really good.
Look at that.
Extremely fine.
I think that micron is the way to go.
So we're going to carefully cut this out with our jeweler's saw.
And like we learned in the last video, under 10 bucks, get you a jeweler's saw.
It's the cheapest way to make a hole in a coin ring.
So let's get to it.
And just like I said in last week's video, we're going to start by
punching a hole in this.
Now this is an auto punch, but you can use any kind of punch you want.
Super cheap.
Sharpened piece of metal.
An old drill bit.
Anything you can hit with a hammer and make a divot,
so that way your drill bit doesn't wander, right?
And you can use any kind of drill you want.
I've got a Fordham flex shaft, so I'm going to use that.
Make sure you don't drill your own finger, right?
That's important too.
Ask me how I know.
And we're going to take our jeweler's saw.
And I like 3-0 blades, but you can get any kind of blade you want, really.
Any blade will work, really.
3-0 is really good middle-of-the-road blade.
Feed that through there.
And like I said before, I usually push this against my shoulder
to get the tension on the blade correctly.
So we're just going to push that.
We'll open it enough and then push it.
Get that tension.
Release of tension.
It's nice and tight.
So I use Pepe lube to keep my blade running smooth.
But you can use oil, like I said in the last video.
This is all kind of going over exactly what we did in last week's video,
but a brief synopsis is you're going to want something to
make this thing run without catching.
When you oil your blade, you keep it lasting longer and it cuts faster.
So that's why we're doing that.
You don't need a bench pin like this.
You can literally cut a V and a piece of plywood
and then just screw it to whatever benchtop you're working on.
And I did it so quickly in the last video, and it didn't come out as perfect.
But it's really important to take your time on this hole
and get it as perfectly round as possible.
Because your entire ring is built off of the accuracy of this hole.
So the more perfect it is, the less wobbly you're going to be.
All right, we are cut through.
And just so you know, this would be the first thing I would update
if I was to buy tools beyond the most basic good tools.
I would be getting something that cut a perfect hole.
But that's not bad.
That's not bad at all.
So we're going to clean that up with our file.
We just want to smooth out anything that's in there.
We don't want anything to not be smooth and even.
If you leave any like weird cut marks in there,
that'll be a place where a split can form.
So eliminate all of that when we get started.
But we still have this sharp edge.
So we're going to 45 this off with our half round file now.
So let's lean the file back.
Get a little 45 action.
And all this is designed to do is to eliminate any splits.
Sharp edges create splits.
So no sharp edges, we will have a lot higher chance of it not splitting
as we start to stretch it.
All right, one thing I am going to factor in
that I didn't really think about until just now is
last time we didn't use a torch.
And I didn't want to factor the cost of a torch in.
And I really don't want to now.
But it makes it so much nicer.
The inside detail remains better.
So what we're going to do is factor that cost in.
So a cheap benzamatic torch, which I will show a picture of here,
$16 something on Amazon.
So it's not that expensive if you don't have one.
So what we're going to do is heat this thing up.
You don't want to get it super duper hot.
If it gets orange, you've gone too far.
So don't get quite orange.
Just a hint of orange.
That's good enough right there.
So it's not too far.
A dark room is really helpful for this when you're getting started.
Okay, now we're annealed.
We'll start folding it.
So this is the most expensive tool from the last video.
It's the one that's the most important too.
It's like the foundation of coin ring making.
So it has a 17 degree side on one side and a 25 degree side on the other side.
But we're going to be sticking with the 17 degree.
And we're going to find a die that this barely fits in.
Which is going to be not that one.
This is the next one down.
And here are the cones that we're going to be using.
I'll put a link in the description box for this and this.
All the tools from last time that we're building on,
I'll put a link in the description too.
But we're going to start with our starter cone.
And get this fold started.
Put it in there.
Make sure it's relatively even.
And we'll start to fold.
Okay, and then we're always checking to see if we can go to a smaller die.
Because we don't want this getting stuck in there.
Because there's not very much depth in these.
Which we can switch to the next one down.
But since we're annealing, we get it folded about that far.
We'll re-anneal it.
Every time you move the metal about 30%, you want to re-anneal.
To folding.
So we're going to go in the next size down.
17 degree die.
And we're going to leave the starter cone behind now.
We've got the fold started.
And we're going to go to the next size composite cone.
And these composite cones are designed...
I should probably go up one size perhaps.
These composite cones are designed to not damage the detail of your coin.
Unlike if we were to have a steel cone all the way.
The steel would rub against the silver.
And obviously that wouldn't be good.
I'm just going to even this thing off the best we can in our die.
And begin to press.
Okay.
We'll go down to the next size up.
We'll go down.
We're going to switch.
So we started here.
We went here and now it'll fit in this side.
This size.
So we're going to go down one more.
We're going to go up a cone size.
And we're going to fold until it stops.
That's what we're trying to do is fold until we can't squeeze it down any farther.
Which we finally bottomed this thing out.
You can see the coin edging is touching the cone everywhere.
That's when you know you're done.
And when it gets stuck like this.
Take a mallet of some kind.
Just hold it tight.
And give it a quick smack.
All right.
We will anneal it now and be ready for the next step.
Okay.
So this next step is where we're going to be buying our next tools.
So this is the next thing we would need to buy for doing half dollars.
This is a Swedish wrap.
It's a .8 up to 1.1 Swedish wrap die.
And it comes with these guys.
These are our push followers.
They're brass.
These will allow you to do half dollar size coin rings.
So what we need to do is shrink the size of this thing down.
So we can make smaller ring sizes.
If you want to make size 13 and up, you don't need this.
But if you want to make below a size 13, which most coin rings tend to be.
You're going to need this guy.
So that is one tool.
In order to use that tool, we also need to get something from Harbor Freight.
This is the Central Machinery one-ton arbor press.
So these are $79.99 or if you're, you know, an Inside Track member, I think they're $55.
And then this kit, you can buy just this single die and push followers on Jason's website for $133.
And the first thing we're going to do is we're going to take some Teflon tape and wrap this up.
So that way we're going to preserve the detail from getting destroyed in the die.
And what I like to do is wrap it 25 times.
It's a little bit overkill for a half dollar, but that's okay.
Teflon is cheap.
Silver is expensive.
It makes sense to use more than you need.
Okay, we will place it in their coin edge facing up in our Swedish wrap die.
And I want to make a size 11.
So a size 11, this first die or this first push follower,
you press it all the way down until it stops.
And that will make a size 11 possible.
We will throw it in our one-ton arbor press.
Press it down until it stops.
Okay, didn't have to go too far.
That's all we needed.
Now if we wanted to make a size 8, you just put it back in the die.
What you need to do is probably bring this back to the ring sizer over there.
Put it down here and squeeze it just a tiny bit to bring that curled in a little bit.
So that way it can accept this next one.
Currently this isn't, this is not narrow enough to make this not slide into your coin.
So you'd have to size it down in your ring stretcher just a tiny bit.
So that way this could go on top.
And you would re-wrap it with Teflon so that way the top is being
saved from getting mashed up with this thing.
So we'll take our Teflon off, re-anneal, and then we'll go back to the ring stretcher.
We're going to put it coin edge facing up on our ring stretcher.
I'm going to put a little bit of a trash bag in the way
to keep the detail nice and safe from the steel.
And we're going to start to stretch it.
And just like before, we're going to keep downward pressure,
short motions, and you turn it slightly as we go down.
And we're going to stretch it until this touches this mandrel everywhere
and that'll keep it nice and even and not wonky and lopsided.
It's a really important thing to do.
And you'll start to feel resistance.
You'll start to feel resistance when you get close to
it being all the way against the stretcher.
So right now I'm starting to feel it's getting a little harder to do.
So I'll give it a couple quick motions and turning as I go.
Just make sure it's good and even.
We'll pull it off.
Again, this is not necessary, but it's nice to know where you're at.
So we want to be two sizes larger than our target size, which our target size is 11.
So we've stretched it to a 13.
And so that's going to do is stretch this backside enough where we can curl this in,
get rid of any this weird angle that we have.
We want it to be even on the outside so we can curl it in enough
to get rid of it and make it nice and even on the outside.
That's why we stretch two sizes larger.
But it has been stretched two sizes larger.
So now we're going to start sizing it down in our 17 degree die again.
Find the one it barely fits in, which is that one.
Put it under our stretcher and we're going to reduce it to
where it is the size that we're looking for, the target size, which is 11.
So we'll check it to make sure we're at 11.
Okay.
And so now what we're going to do is flip it over to the 25 degree side.
This is going to curl the coin in a little bit faster.
And we're going to go a size below our target size now.
We're going to shoot for a size 10.
Okay.
And we're sitting just below a size 10, so that'll work perfectly.
And now we're going to flip it around.
We've been sizing this down.
So we're going to flip it around the other way.
Keep it in the 25 degree side.
And then just make the outside of the coin ring match and look even.
It's pretty close.
A little tiny bit more.
I think we'll be there.
Perfect.
All right.
So now we'll take our half round file and we're going to sand this cut edge away.
Just like we did the quarter coin ring in the last video.
That's really sharp.
And that's why we size it down below our target size.
Because we know we have to get rid of this.
And we'll make that rounded off.
And then we'll hit it with some sandpaper when we're done with that.
And make it nice and smooth and comfortable.
All right.
That is sanded out of there.
And it's exactly at a size 11.
Fits really comfortably.
Time to go clean it and antique it.
Finish it up.
Okay.
Throw it in our jeweler's pickle.
Basically we're just cleaning this.
And you'll see in the description the type of jeweler's pickle I'll use.
All right.
It's been in there for about a minute.
So we're going to pull it out of there.
These are copper tongs.
Or you can use a straw or something.
Just don't use steel.
Rinse it off.
And dry it up.
Don't touch it.
Any debris or any soot or anything that might be on there.
We need to get it off.
We don't need to put any of our oils from our fingers on there though.
So be very careful not to touch it.
Okay.
We just got some hot water out of the microwave now.
Put our liver of sulfur XL gel.
A couple drops of that in our water.
Stir it up.
And then throw our silver coin ring in there.
And this is going to basically put that antique finish on it.
We'll leave it in there for a minute or two.
Okay.
It's been in there for about a minute.
Out of there.
Now we have a nice dark antique finish.
Dry it up.
From here we'll take some 4-0t steel wool.
And lightly remove some of that antique.
To leave the details standing out a little bit better.
And so the cool thing about this.
So the first video I did last week with the quarters.
It would take five or six quarters to sell to completely pay for those tools.
And now we've added a couple more tools.
And say you need two more half dollar rings to sell to cover these tools.
That's really attainable guys.
And that's a beautiful coin ring.
That is a really nice coin ring.
And it's extremely high quality.
It's not made with junky tools.
So a lot of times you're fighting the tools.
And we'll take our connoisseur's jewelry wipe at this point.
Just give it a quick polish.
Yeah you don't want to fight the tools.
And fighting the tools making a lower quality ring.
It's not necessary really.
It's not that expensive.
It doesn't take that much to overcome.
So I would encourage you guys to buy the right tools.
And slowly build your kit like this.
This is the way to do it.
Look at that.
That is a beautiful coin ring.
All right guys if you found this helpful.
Please give it a like.
I appreciate that.
Helps me out by pushing this video out a little bit farther.
And if you guys were interested in buying a coin ring.
Check out my website changeyoucanwear.net
I will leave a link in the description box below for that.
And I will catch you guys on the next one.