Details on how to make a Silver Australian Florin Coin Ring

Change You Can Wear
145 followers
2 Video Views·Jul 24, 2026
Check out my website www.changeyoucanwear.net to buy this ring or any other I make or to schedule a coin ring class!
AI Generated·May contain errors
Video Summary
AI GeneratedSkyler from Change You Can Wear demonstrates the process of transforming a silver Australian florin into a size 11.5 ring. The video covers the entire jewelry-making workflow, from the initial coin punching and annealing to the final antiquing and polishing stages.
Hey guys, Skyler here from Change You Can Wear and Sojourn Fine Jewelry. Today we're making this
silver Australian florin into a size 11 and a half ring. Awesome coin. These are one of my
favorite foreign silver coins to make. They just look beautiful. So let's get started. The first
thing we're going to do is take this auto punch from Jason's Work and we're going to pick a half
inch punch for it. If you haven't noticed yet, half inch is my go-to punch basically for almost
everything except for Morgans. It's a really good size for most coins that are quarter sized on up
to not quite dollar sized. Half dollars for sure though. And this is kind of in between a half
dollar and a quarter. It's more closer to a half dollar than a quarter. So it'll be a narrow-ish
band but not like stupid narrow. It'll be like seven millimeters something like that.
All right. Take our take our teardrop mallet. Get it off the punch. Take our deburring tool.
I got this one at Wilco actually. It's a really nice metal one. If you'll see most of the time
I was using these guys and these are good too. I got these on Amazon. There you get like a pile of
blades. A little handle comes almost for free. By far the cheapest way but this one just feels so
nice. It's ergonomic because it's smaller and I still buy the blades from Amazon because you
can't find the replacement blades. I don't even think at Wilco or I haven't been able to. I have
not ordered replacement blades in I bet you four years and I'm almost out so I have to go order a
There's no chatter marks. Everything's nice and smooth. We don't want it splitting. That's the
purpose of doing all that. All right. Let's anneal it. We'll heat this thing to a dull red which is
really hard to see because the light's just pouring in but a really dull red. You don't want to get
it too hot. Doing it in a dark room is way nice but this will work. That's plenty good right there.
Grab it and quench it. Now we need a 17 degree die. The one this coin barely fits in. This one
is a little big but the next size down isn't quite. It could probably work but it's not quite
big enough. We don't want to damage the reeded edge so we're going to go into this guy and we're
going to fold it. We'll start off with a steel folding cone. You know what I haven't done in a
limited tool kit. So if you're just doing half dollars and quarters maybe we should do a tool
list video that only shows what you need bare minimum to do half dollars and quarters really
well. Maybe I'll do that next week. Until then we're folding this thing. We're going to switch
the next size down just to make sure we don't get it stuck in our die. Yeah if you guys want
to see a video like that with limited tools we can see limited good tools. Let's put it to that
because I am tired of making videos of junky tools. I did that for a while. It's just not
satisfying. If it's worth doing it's worth doing well. Okay so that is folded. Let's re-anneal it
since we work hardened it and then we'll sand this edge. I think that'll work. We don't need
wrap this one. We're going to be going up to an 11 and a half and this is small enough already
to get there. Put some plastic in between the coin and the ring stretcher. Start to stretch
and notice I'm stretching just a little bit turning the ring a little bit stretching turning
as I'm pushing down on it and that is to make sure the thing is stretching evenly. You're not
going to get stretch marks on the inside of the band because when these expand over and over in
the same spot you'll definitely get stretch marks in those areas and we don't we don't want that.
We're making a size 11 and a half so we need to stretch this two sizes larger than our target
which is a 13 and a half which is exactly where we're at. So now what we're going to do we're
going to take a 17 degree die. We could either use one of Jason's dies or Pepe Tools makes
a coin ring die which is a little bit larger than a regular die and it has 25 degrees and 17 well
25 degree on this side 17 on this side. Let's just use this one actually. We're going to
fold it down with a 17 degree die to our target size which would be 11 and a half.
Yeah 11 and a quarter I went a little too far but that's okay we didn't hit any detail so
and then we're going to switch to the 25 degree side to get it to curl in a little bit faster.
We'll go a size below our target size. Oh that was too far. That was too far. That was way too far.
So when we go too far, you think that was on purpose just to show this? Probably.
I wish that was the case. I accidentally went too far. We're going to stretch it back before
we start sizing again. We want it just to be a size below our target. It's about right there.
Now that we've done that we're going to stay on the 25 degree side flip this thing around
and make the outside match that same contour and not go over this time. Let's deburr that inside
there's that sharp edge that's in there and then we're going to deburr it back to the target size
which is 11 and a half. I'll take a little bit more used up sandpaper and finish cleaning up that
cut edge that we or the the area that we just deburred on the coin edge. I'm gonna make that
nice and smooth and pretty. Perfect. And we always do a little bit of deburring on this cut side too.
Sometimes it curls in and gets a little sharp. We don't want that so we'll clean that up.
All right it's a size 11 and a half. It's good shape. I love the design on these things so much.
It's time to throw it in a pickle, clean it up, and then we'll antique it. And this is what the
pickle I use. It's Bench Basics Smart Pickle. This comes from Pepe Tools. I get all my, well, I get
most of my chemicals from them. All right we'll leave it in there for, I don't know, 10 minutes.
It'll be clean in about 10 minutes. All right check it out. It hasn't been 10 minutes, it's been
like five and it's like perfectly clean. It doesn't take long. So we'll rinse it and then not touch it
but just wipe it down with a clean rag. Don't touch it though. That's the sound of our water
being done, being warmed up. So we got it just about boiling. That's now ready for the liver
of sulfur. So we'll get the liver sulfur ready now. All right we got our water that's nice and
hot. A couple drops of some liver of sulfur gel. Stir it up. Dump in our ring. We'll leave it in there
for about a minute. All right it's been around a minute. Let's fish it out of there. Make sure
we're not using the same tongs that we used to get it out of the pickle because it makes
the liver sulfur go like nuts. There's a chemical reaction and it ruins the finish. All right so we
have that. Rinse it off again. Got a nice even antique on there now which is great.
Now we'll take some of it off with some 4-0t steel wool. Okay so just a light touch on the inside
first. Does it matter if it's first or last? I guess it doesn't really matter.
This is the way I do it though every single time. Coin edge. Nice. Cut side.
Nice. Finally the outside. Yeah that's beautiful. Check it out. Let's get some good
video shots of this now. Thank you guys for watching you guys. If you were interested in
taking a class I've really enjoyed having you guys out here. A lot of you guys who've come out
and taken a class with me. Check out my website ChangeYouCanWear.net for scheduling that or if
you want this ring. This ring is going to be available. It'll be $125 for this guy. If you
want it contact me through my website ChangeYouCanWear.net. Pick it up. Thanks guys. Catch you on the next one.
