How to Cast Blackberries in Bronze

Change You Can Wear
145 followers
Aug 13, 2026
Be sure to check out my website!
www.changeyoucanwear.net
AI Generated·May contain errors
Video Summary
AI GeneratedThe video demonstrates the lost-wax casting process to transform organic materials, specifically blackberries and other natural objects, into bronze sculptures. The creator guides the viewer through the entire workflow, from preparing the organic specimens and creating a sprue tree to the final casting and polishing of the bronze berries.
Here is what we've collected, there's a couple little guys.
Really the green ones are the ones I think I want the most because they're the stiffest
and they're going to hold up the best to the process.
So what we need to do is I'm going to clip all these and then clean off some of this
stuff, so that way there's not as much of it on there.
And we're just going to go ahead and clip these manageable chunks, I'm going to eat
this one.
I want to keep these little guys, I think they would look cool to be on there, unfortunately
when they're really green like this they stick up really high, so I'm trying to pull them
down a little bit so I can get to the stem.
They don't stay down, but I'm helping it for now, I think they would add something
to it.
So I'm going to cut the stem off as close to the bottom as possible and then I'm going
to come through with a sprue wax, this is 8 gauge sprue wax and this is a wax pen, Pepe
Tools wax pen.
I'm just going to preload a little wax on that area to fill up any porosity that might
be in the top of this thing, because what I want to do is whenever this thing casts
that needs to be solid so that way the metal will flow through there really well.
So I'm going to add this wax in there to just solidify it, and this is where our sprue is
going to be going in too, so we want somewhere for the sprue to actually connect to.
Once we've got enough wax in there I melt the tip, it is really hot today too so this
wax is having a hard time cooling off to solidify.
Anyway, so that's on there now and we're going to cut kind of a long sprue, we can always
shorten it later, and then I'm just going to clean this up, I want to make sure we've
got a good connection down there so I'll just melt the two pieces together, the bottom wax
that I put on to begin with and the sprue I just squished on, and once that's done we'll
set it aside and we'll do the rest.
So I'm going, I decided just to do ten, I'm going to do ten of these guys.
Now it's time to finally put all of these guys on here, I'm trying to decide how best
to do that, I don't think that's, that's way too long, we're going to cut some of these
back.
This is the base we're going to use, we're going to cover it with a flask when we're
done so we've just got to make sure that these are all on the center of this base and that
they're not too close to the edge.
So we're going to start off in the middle and basically work my way around here.
Well, yesterday I quit because it was too hot in here and I didn't cast those berries
that we were spruing up, and when I came in today they were all shriveled so I had to
start all over again, which is cool because I was talking to my sister-in-law yesterday
about what I was doing and she had a couple other cool things that I was going to try
to cast.
So this is a root ball, I really don't think this is going to actually work, it's so very
fine and it's broken in places.
So if that fills, that would make something pretty cool looking, and obviously a baby
turtle shell, which is pretty wild, it's, I don't know, it kind of grosses me out to
be honest, when I was spruing it up it kind of grossed me out a little bit.
Either way, we're going to cast them and see how they work.
I made a sprue tree that's a little more, you know, appropriate.
I made a center stalk and had all these come off a bit, so that way we can fit a little
bit more on there.
Turned out much better than the one I did yesterday anyway, so let's get this invested.
The first thing we're going to do here is spray this with something called VacuCoat.
Basically just like it says, it prevents bubbling, so it'll keep bubbles from sticking to these
guys when we put the investment in.
And then this is our flask we're going to be using.
Put it over the top of our base, just slots in there.
I don't think I'm going to need this this time because I'm not going to make as much
investment for it to overflow.
Put this on so that way whenever we do put it in our vacuum chamber, the investment's
going to expand and start bubbling.
We're degassing, basically.
And so this is just to prevent it from bubbling over.
So we got our container we're going to be mixing in.
We have our measured out water.
And depending on, you know, the size of the cast you're going to be making, it depends
on how much you're going to be inserting there.
The name is UltraVest, that's what it's called.
And that's the powder we're going to be using, which is over here.
Ransom and Randolph UltraVest.
All right, so we're going to get the amount that we need out of this guy.
404.
Perfect.
Now we'll add it in and mix it for three minutes before we degas it with our vacuum machine.
Put it on and put the vacuum on again.
Okay, once we get to a full vacuum, this is going to expand and then start to boil.
Once it boils, we'll hit the table for about 10 seconds to make sure it shakes all the
bubbles loose.
And then we'll take our vacuum away, pour it into our flask, and once it's poured in
the flask, we'll vacuum it again just like that.
And once that's done, we'll let it sit for two hours before it goes into the oven.
All right, we're starting to boil.
Once it boils and it breaks and comes back down, that's the key there, which is done.
We'll leave that for two hours.
It's been a little bit longer than two hours.
I had to wait for a bit because we had a thunderstorm and knocked the power out.
So thank goodness we didn't put it in earlier, because we would have ruined this mold.
So we're going to take this base off.
And so that's where all of our sprue tree is going to be melting out of.
And we're going to pull this tape off, which we kind of needed it.
Look at it.
Some of it was going to splash out.
It's a little low, but that's still going to be fine.
It covered everything that we needed to cover.
So once we have this, we'll throw it in the oven.
Put it in there, and we're going to put this facing down so that way all the wax can melt
out.
All of the ash will come out from the organic material burning out.
And then we have a special program that we run for organics.
So this is a lot longer of a program than if it was just basically a wax.
So I have it programmed in this as Program 2.
So we're going to pull Program 2 and take a look at it real quick.
Program 2.
And the first ramp is a full ramp, so it's as fast as it can heat up.
It's going to heat up to 300 degrees.
We're going to hold 300 degrees for two hours.
Once we're done with that.
And that is basically to start melting the wax that's in there out.
And once we do that, we're going to ramp.
What this means is over the course of five hours, we're going to ramp up to this next
temperature, which is going to be 1,350 degrees.
And so at this temperature, you're going to start to burn up any organic material out
of there.
It's going to start turning to ash.
And we're going to hold this a long time.
So it's going to be held for 12 hours.
After 12 hours of that kind of intense heat, everything that's in there should be completely
burned away and gone.
It's a good idea to get some canned air in between this time frame and try getting some
air blown in there to get rid of any ash that might be in there.
I haven't done that in the last several, and everything's been pretty good.
So I'm going to probably not do that.
But sometimes it's nice to get some of that ash out of there by doing that.
Anyway, once that ramp is done, we're going to come down to our casting temperature.
So we're going to ramp full as fast as it can go down.
It'll go down to 1,100 degrees.
And we're going to hold this 1,100 degrees for quite some time, 20 hours here.
And the reason we do that, just in case something weird comes up tomorrow, I can't cast it for
some reason, I give myself a long time for it to sit at that temperature.
And whatever my schedule is, I should be okay.
So that's why we do it that long.
So we'll see you guys in, I don't know, 20, 24 hours.
And we will see if we can't put some bronze in there.
It is now the next day.
Our mold is ready to cast.
We have our bronze.
I don't really know how much to use.
This is the problem.
You can see last time I casted some bronze, I used way too much, and it got stuck to the
crucible, which is really not good.
But jeez, I hate to not have enough, you know?
So we're going to throw in about, we're going to make a mess first, about three and a half
ounces of bronze.
So that's a fair amount.
I'm sure it's more than what we need.
Hopefully it doesn't quite get this insane, but we're about to find out.
That's probably way too much, way too much bronze.
What are you going to do?
Still an extremely full button.
Look at that.
It's very full, but it wasn't full enough to, you know, I could have guessed worse.
That wasn't bad.
All right.
The moment of truth.
Will it have worked or won't it?
And how much of it will work?
Let's see.
I kind of knew that one wasn't going to work.
It was too fine.
The turtle shell, though.
The turtle shell.
That's a surprise.
I thought that was a little thin, too.
All right.
We'll clean this up and get a good look at it.
That turtle shell was a little too good to be true.
It was just way too thin.
It was like thin as a piece of paper, maybe even thinner in areas, but all the blackberries
look great.
Little bronze berries now, huh?
All right.
I got all of our little blackberries all cut off the sprue, and what we need to do now
is get rid of these little, these little sprue nubbins, and once they're done, off of there,
we will solder on these little jump rings that I made, and then we should be, we'll
polish them up after that.
We'll be good to go.
Anti-oxidizing coat on it.
All in all, I like them.
So the problem, though, with berries is they're so full of juice, that liquid messes up the
casting in areas, but still, I think they're pretty cool.
Anyone who's been to Oregon has eaten blackberries off the side of the road for the most part.
Since I'm down here, I might as well eat a couple.
All right, guys.
Thanks for watching, and I'll catch you on the next one.
