They're Calling this a Dresser!?

Thomas Johnson Antique Furniture Restoration
41 followers
211 Video Views·Aug 1, 2025
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine restores this handsome Welsh Dresser. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson, Thomas Johnson, Antique
Furniture Restoration in Gorm, Maine. My
summer beach read this year is this
book, Oak Furniture, the British
Tradition, Victor Chiny.
This book is fascinating. It talks about
the origins of a lot of pieces of
furniture that are very familiar to us
to this day.
You really see the evolution of the
different styles of furniture.
And I've always been fascinated by the
fact that they called these Welsh
dressers
dressers. I never understood that.
You see, here's your dressers with no
cupboard above. And the board here, that
board
was where food preparation went on. So,
we might call this piece a sideboard
today. And I call the upper part
a cupboard. So, it's a low dresser with
a cupboard, or
as we call them, a Welsh dresser.
And that brings to mind a Welsh dresser
I had here in the shop. It came in
because the crown moldings on the sides
were cracked.
That molding on the right side gave me a
devil of a time. I remember it like it
was yesterday.
This is a nice antique. Uh I'm calling
it a Welsh dresser. I've been calling it
that, but uh it's not really a dresser.
A dresser refers to a sideboard where
you'd have a surface to to serve food
from. And this it's just like a Welsh
dresser except it doesn't have the the
sideboard. It doesn't have the main
board. I'm going to call it a Welsh
cupboard. And it's I think it's made of
elm. And it's actually in pretty good
shape. It's got the main thing that's
wrong with it is the two end moldings.
This molding especially is broken and so
is the other one. And it also has some
minor stuff in it. It's got some water
damage to the feet. And uh and actually
there's something dripped uh all along
this base and uh we'll have to get that
off. And then there's a couple of other
things here and there that need to be
glued.
All right. I had a neighbor help me take
the case off of the stand. And uh the
first thing I want to do is see if I can
get this molding off of here.
[Applause]
So, I'm doing one area at a time, trying
to heat it up very carefully. I'm
watching very closely to make sure that
uh I don't see anything happening here.
I don't want any scorching or anything.
And then uh I do it for 2 minutes. And
then I tried prying it with a scraper.
[Music]
Now you can see where someone uh added
this board here to help support the
molding. Uh not a bad idea. Actually,
that seems pretty sturdy.
This side is quite sturdy. I think I'll
just uh improve these touch-ups.
Fill this area in. Fill that in. And uh
touch up a little bit right here.
It's easy to see that these aren't
original nails.
[Music]
Well, I I don't think anyone will be
surprised that this is a really lousy
glue joint. Uh really kind of
non-existent.
So, I'm going to uh epoxy this back
together. And I think I'm also going to
get some oak veneer and use it as a
backer.
I think I'll put a block here so I can
use that to position these in the exact
alignment.
This block is covered by clear packing
tape.
You know, I'm going to put a block here,
too, to give me something to clamp
against.
You can see that as I put the squeeze on
it, these pieces want to come up.
I've got a big dowel here. I can use
this to hold it down. I will uh cover it
in plastic.
I need to have an idea
of where
this should be.
I won't be able to see if it's together
when I have put that block on it. Now,
I'm going to color the epoxy. This
piece, I noticed from the beginning, is
very dark. And I don't think it's dark
because I put the heat gun on it. It was
always dark.
Yeah, that's the color of the rest of
the cabinet.
Okay, I've got two-part epoxy,
a thickening agent,
powder stains, soluble and alcohol, and
I have alcohol for cleanup and a paper
towel.
Well, it's going to be interesting to uh
see what this looks like tomorrow.
All right, let's see what we got here.
No surprises there. There we go.
Boy, seems good and strong, too.
All right, I'll try to uh chip off some
of this excess epoxy uh with a chisel.
Ultimately, it's going to need to be
sanded. Epoxy is tough to get off. And I
need to fill all the gaps with uh epoxy
putty.
This is a nice scraper set I bought with
changeable blades.
Maybe this will help me with this big
cove molding.
[Laughter]
Now I'll fill these gaps with epoxy
putty.
Uh people like to call this Tootsie Roll
putty.
Now, epoxy putty
is very difficult to sand when it's
fully hardened. So, I set the timer for
5 minutes. I'll get some water and I'll
dip my blade in water, maybe even a
scraper blade, and try to carefully
remove as much of the excess as I can.
[Music]
I don't know why water works so well
with this stuff, but it does.
Okay, while I'm waiting for that uh
epoxy putty to fully dry, I need to trim
this piece of veneer I put on the back.
I've sanded the back of this uh trying
to flatten it. So, the veneer is almost
gone, but it's still doing its job. But
I need to try it on here to see how it's
fitting. So, I need to uh get these
nails out and prepare that surface.
[Music]
Just what I thought. There's there's two
things happening here. I mean, this the
back of this is not completely flat.
It's It's cuped a little bit this way.
And then this end grain sticks out a
little bit past here. So
you got quite a rocking motion here.
I'm going to try to take a little bit
more off the back of this.
And then I may just have to add
keep it flat against the cabinet here,
but add some wedges along the top here
to give it some support.
Boy, taking that off the back of this
molding has really helped a lot.
I don't think I should take off anymore.
It's It's rocking on this end grain
right here. I've got to I've got to
really take away some right here.
Boy, this is uh this is fitting so much
better now. Still open here at the top,
but I think that that's as far as I can
go with that. I think I'm going to
glue and nail this here in this position
so that this is flat against the
cabinet. And I want to add a wedge piece
in the top here for support. That will
also fill this gap.
All right. I've sanded this uh uh really
well with 100 and then 150. And I'm uh
I'm anxious to see what the colors like.
I'll uh
I'll put some alcohol on it.
>> Color's perfect.
I'm going to give it a coat of this uh
this oldfashioned varnish and then
tomorrow I'll do the touch-ups
doing it before uh before I install it.
Okay, this has dried overnight. I'm
going to go over it with a uh gray ultra
fine pad and do the touch-ups.
I'm using a brush tip marker.
Okay, this will need uh another coat,
but because it would have to dry
overnight, I'm going to uh install this
on the cabinet first.
I've still got a little bit of this
problem up here. I'm going to nail this
to the carcass. That's the way it was
originally done.
I'm going to use a little bit of glue
in this area here where it joins this
piece of molding.
And really just the lower part here.
I'll nail across here. Then I can make a
wedge to fit in here to give it some
support. At the top, I put some double
stick tape on this block just to help me
hold it in place
while I nail it.
The hot glue is just going on
this front part here.
Well, that seems uh pretty well secured.
Just like that. But I still want to put
a wedge behind this upper portion. I'll
glue it in with a little hide glue. So,
this will just give this a little extra
support back here. Because the grain of
the piece of molding, this block, and my
wedge are all going in the same
direction, uh, I feel okay gluing it in
there.
Now, I still have to make a wedge for
this front part here. I have a piece of
uh white oak very similar to this wood
here and so I'll make it out of that.
So now to the other side. This molding
has also been broken in the past but it
it's really strong. Uh but definitely uh
need some touch-ups. I don't know what
happened there. And there's a hole. Who
knows? I'm going to use epoxy putty on
this. Because it's on a corner like this
on the outside edge. First, I'm going to
poke some holes in it to help anchor the
putty.
Then a little bit of water on the knife.
A little water on the fing my finger.
And then after about five or six
minutes, I take a gray pad and you can
gently
remove a lot of the excess here.
Now we can turn our attention to the
base. And um it's kind of odd. The base
has drip marks all over it. Uh water
damage to the feet it looks like. And
it's odd because there's no drip marks
on the uh on the case above it. So maybe
they were in separate locations and
something happened. But um I'm going to
take some uh scratch cover and steel
wool and go over this and see if it
helps.
It looks great with the uh scratch
cover, you know, and the steel wool to
help clean off the surface. Um, but you
never know if it's going to stay that
way or not. And so I'll go over the
whole thing with a scratch cover and uh
scrub it down and let it dry overnight.
We'll see tomorrow.
Most of the drip marks seem to disappear
except in this area and this area. Um, I
got a I have now have some two, so it's
not quite as fine. And uh I'll get a
fresh piece and go at these two areas
again.
Well, I decided to try one more thing.
I'm going to use a uh maroon pad, which
is a medium pad.
And that seems to be
doing the trick. All right, this is
dried overnight. I've got to trim this
patch down, this little wedge. But
first, I'll um on the other end, the
piece of molding that had all the cracks
in it, I've got to touch that up.
You know, that putty smoothed out really
well. I did sand this with a little bit
of 150. And uh these areas are so large.
I'm going to go over them with some uh
dark walnut dye stain that's been really
uh thinned out quite a bit.
[Music]
stitch.
[Music]
I don't
had a little gap right there. I put some
putty in. Uh while that's drying, I'll
go back to the other end. Well, there's
a a kind of a big crack here. I think
I'll use uh the low heat burning sticks,
the wax sticks to fill some of that in.
I'm going to wipe off this excess and
see what the color looks like before I
go any further.
It's a little light. Maybe I'll try the
dark walnut.
Yeah, I think it's going to look better.
I'm going to use a little bit of a
perfect brown dye stain. Really thinned
out. I don't think it'll take much to uh
do this end grain.
Okay, this is the side that was broken
so badly. I kept I keep looking at it
wondering if it needs more color or not.
But I think what I'm going to do on both
end moldings is uh pat them with a
little satin varnish. And I think the
color will be fine.
This is the same uh type of varnish I
used before, just the satin version. And
I'm not going to brush it on. I'm just
going to pat a little bit on.
Sort of seal everything in.
Same thing on the other end.
All right. While everything's drying on
the cupboard, I'll go back to the base.
And yeah, I can still see shadows of
some of these vertical lines. Uh, but I
am just not going to worry about it. I'm
not going to sand this down. Uh,
I'm just going to polish this up with
the uh Howard's feeding wax, which is uh
orange oil and beeswax.
And
I think it's going to be fine.
Well, there you have it.
this really beautiful uh what I call a
Welsh cupboard. It's very old. I think
it's made of elm. The only thing it uh
came in for really was these uh this end
especially. The two end moldings were
damaged. This one very badly. And then
of course I found other odds and ends to
uh repair and touch up along the way.
And
yeah, it it it looks pretty good.
I got one more gallon.
I hope you like the video and if you
did, please subscribe and like and be
sure to hit the bell icon so that you'll
be notified when I put out a new video.
