Antique Treasures, Restored! - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
81 Video Views·May 29, 2026
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, , or write us at [email protected]. And for those on the east coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
AI Generated·May contain errors
I'm Tom Johnson, Thomas Johnson Antique Furniture Repair in Gorham, Maine. We still have t-shirts
available. You can order them from my website. I like this compilation because they show the
reality of a real furniture repair shop, you know, not big transformations, but your
everyday simple, a lot of times not so simple repairs, and the goal of which is to make the
furniture look like it had not been repaired. I also really like the detail in these videos,
so if you enjoy repair work, I hope you like the videos. Hit the like button, share.
I'd really appreciate it. I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration,
in Gorham, Maine. These are two nice pieces of furniture. They're 20th century reproductions,
probably made for export in Asia, and they are copies of the 18th century furniture
when chinoiserie became very, very popular. They were damaged in a move. The chair had a foot,
the piece of wood in the foot, broken off, and the table, a piece of the molding was chipped off,
and the molding is also loose. This tabletop has some rather normal wear and tear on it,
but my work is limited to just the moving damage. So this glue-up is a little more problematic than
it first appears. I want to use the spring clamps on this. They didn't seem to be working
at first, but if I can position it correctly, it does. And of course, then I discovered that
this type of spring clamp, which has expandable jaws and these swivel points,
works really well for that. But I still have a problem with the broken pieces.
See, I'm able to clamp down this lower part here, and I think clamp that pretty well together
like that. But when I do that, the back of it is not together. So I've got to figure out a way
to clamp the front of it here, but I've got to somehow get a clamp in there to bring that
together. All right, I think I've got this figured out. I have a small spring clamp to get
this upper part of the molding, and then I took a small block. I beveled the edge to kind of fit
inside the cove here, and I'm able to clamp that on. And of course, I can't see what's under the
block, but I'm pretty sure I have that together. At least I know I've got it together as best I can.
You know, this really emphasizes how important it is
to do a dry glue up before you put glue on there. I've got some nails in there,
and obviously it's an old break. I'm going to go over this with a wire brush this way,
give it a little tooth as they say, maybe help keep it from sliding when I glue it up.
So this thing really wants to slip and slide, but as the glue tacks up a bit, eventually it grabs,
and hopefully will stay there. Okay, let's see what we got. Well, it really glued up well. Now
I got a deal where all this wood is missing, which of course is a result of all the nails
that someone put in there. All right, now for this one. Boy, this came together really well,
kind of exceeded my expectations. So, first thing I'll do is get a damp rag and clean off
the excess glue. Okay, I think I got, I think I got all the glue off. This, you know, a job like
this really brings up the importance of using water-soluble glues because you do not want to
sand the surface. You got to be able to get the glue off, and I think it worked out pretty well.
So now the areas where there are these little bits missing, I'm going to burn in some wax.
All right, the waxing part went pretty well, but now I'm going to get back to this chair.
So I have a little bit of a gap on this side. I'll have to use some
wood putty. Okay, while the putty dries on the foot, I'll get back to the table.
I need to use some black stain in some little areas here. Even though it's not really part of
the job, before I wax this top, I'm going to at least, I'm going to take a little alcohol
and see if these white hazy areas might come out. If they come out easily, great. If not,
well, there's not much I can do with a painted top like this. Well, I think it's actually helping
a little bit. I'm not going to push my luck too far. Like I said, you're kind of limited
to what you can do, but if I can improve it a little bit,
that'll be good. I'm going to quit while I'm ahead here. I'm going to let this rest
and get back to the foot on the chair. All right, now I'm going to stain it with some black dye
stain. So while that stain dries, I'm going to wax the top. All right, back to the chair.
I'm going to spray that area with some black lacquer. Now I'll sand my repair area with a
little bit of 500 gold paper, and now I'll hit it with a little clear satin. All right,
I've let the lacquer dry, and I'm going to go over this area with some steel wool and my oil and wax
polish. And then I'll go over the entire chair, not with the steel wool and polish, but just with a
rag and the polish. I use steel wool here just to help smooth it out a little bit.
So there we go, two nice reproduction chinoiserie pieces of furniture. They just suffered some
moving damage. They weren't in terrible shape or anything. I repaired the foot here on this chair
and repaired the molding that had been broken up in this area here. And of course, I cleaned them
up and waxed them a little bit. I think they look pretty good. I'm Tom Johnson, Thomas Johnson,
Antique Furniture Restoration in Gorham, Maine. This is a nice little table. It could be a plant
stand, sculpture pedestal. It's kind of in a Victorian style, but I don't think it's 19th
century. It's probably early 20th century. This kind of furniture, they combined a lot of styles,
so it has a lot of Victorian elements with the incised carving, but then it has Chippendale legs
on it. It's black, but I think that's the original finish. It doesn't appear to have been refinished,
but it's a nice table. Very common problem with a lot of furniture that comes in here. It has a
cracked top with a very wide gap, and that indicates typically that the top is solid wood.
And if you look underneath here, it's glued down all the way around. They did not allow for it to
expand and contract, so what I've got to do is take the top off, glue it back together,
and then reattach it in a manner that can allow for expansion and contraction. So you get the
idea. I'm just going to keep going around the inside here. There's 12 blocks, so I'm finding
these blocks to be pretty tough, so I'm keeping the heat gun on each block for two minutes. I'm
using a timer, and then I'm finding I can slip the knife. I keep the putty knife near the block too,
so it's heating up, and then I'm able to go in through here. Okay, I think I'm going to get the
rest of these glue blocks off of here. Scrape this down a little bit before I go to glue the top back
together again. Might as well use the heat gun on some of this stuff. Boy, that was a lot of glue
scraping. I can't believe how much they glued everything on this table. So during the process,
only one side panel was loose. I'm going to glue that back where it belongs now. This joint on,
you know, where the top was separated, that joint had been glued previously too. It's filled with
glue, so I'll apply a little heat and hopefully it'll come off. I don't want to lose any wood if
I can. Now I want to add my own blocks to the base to which we will attach the top.
So when I mount this top on the pedestal, the shelf grain I can see is going this way,
so I'm going to do the top the same way. The grain's running this way, so it's going to expand
and contract across its width. So I will glue my blocks here and here. So now I'm going to place
the top and I'm going to clamp it with the grain running perpendicular to these two blocks I just
put on there. So now I'll attach the top with round head screws and washers. I trust you've
sort of figured out what I'm doing here. I've glued these blocks to the frame. The holes are
slotted. The round head and the washer now will allow this top to move. These screws can actually
move in those slots. Now I want to make that screw just snug. Hold it tight, but I'm not
cranking it down. All right, so now I'm going to just clean the top real quickly with a little bit
of commercial cleaner. There's a little bit of glue here, but since this is water-based, it'll
take the high glue right off. Now the joints, of course, it's not perfect. It's good.
It's got a few, there were a few little chips of paint and maybe some wood here. I'm going to fill
those in with the low heat burning stick, which is basically a really hard wax that you melt into
the defect with a hot knife and then rub it off. I'm just going to run this wax, really, I'm just
going to go along the whole joint. There's lots of little openings even in the end here. I'm just
going to do the whole thing. So after getting off as much wax as you can with the flat knife,
then you just take a rag and buff off the excess. Now I'm going to go over, there's places where
there's some raw wood showing, and I want to go over those with the black magic marker.
I'm going to use a paste wax on this top because it's a, you know, kind of a hard,
shiny surface. And this wax is a dark brown wax. If I had black wax, I'd use that, but I'll use the
dark wax anyway. So there you go. This is a nice little Victorian style pedestal, table, plant stand
or whatever. The point, it didn't need a lot of work, but the point of this video is really to show,
because it's happened so often, this is a solid top. It was attached in such a manner as to not
allow it to expand and contract, so it cracked. We reattached it, you know, with the screws,
allowing it to be able to move. There's a lot of furniture that comes in here where the tops are not
attached correctly. And to tell you the truth, probably more than half of them are not cracked.
They don't crack. Who knows why? You can just leave those alone. But when one is cracked like this,
that's really the only way to repair it. The crack is still there. You know, we didn't
refinish the top, but it's serviceable now and it looks pretty good. I'm Tom Johnson,
Thomas Johnson, Antique Furniture Restoration in Gorham, Maine. This is not an antique. This is a
reproduction chair. It mostly resembles the William and Mary period from about the year 1700
in England. This chair fell over. The crest wheel broke off. Luckily, I believe I have
most, if not all, of the pieces. So the first step will be to put this back together dry without glue
and figure out what I want to glue up first. So this seems to be going back together pretty well.
Got a big chunk missing here, and there's a chunk missing on the back here. So
let's see what we got in the arts department. There's some little pieces
missing here. I'm hoping that these are the little pieces I have over here.
So the first thing to do, I guess it's kind of obvious, I'm going to glue back these big
pieces that I have and also like where this
crest wheel is split. I'm going to do all those small glue-ups first.
I don't think there's one clamp that's doing the job. I better get some others.
I've got the missing pieces here, but I think I'm going to have to do this in
stages. I'm going to do the split part first and then do the broken part. Now I've had these clamps
on for a couple hours, so I'm going to take them off and glue on the remaining little pieces here.
There's still some pieces missing here, and I have some shards, but I don't think I can
fit them back in there. I'm just going to have to fill that. These chips glued down okay. I wish they
were a little better, but I'm missing a piece anyway. I've got to fill this in. I've got some
other voids to fill in. I think I'll do this work first. There's also, I noticed on the bottom here
is some chipping that probably explains some of these little pieces. I wasn't sure where they
went yesterday, so I've got to fix this up. So I'm going to mix up a little epoxy putty.
I'm going to add some stain to it. This is a powder called blend all stain. It's like a dye
stain. I'm going to mix that in with the epoxy putty. I'm just going to fill in this place in
the bottom. The chips are so shattered I can't glue them in. I'm going to fill them with epoxy
putty. It's on the underside here, and I'll use a little of that to fill in my missing places here.
In the minutes after mixing up the epoxy putty and applying it, I put a little water in this cup,
and then you can take your putty knives or even your finger and smooth it out quite a bit.
Now I'll set the timer for five minutes because the timing is kind of critical on this epoxy putty.
In five minutes I'm going to take a great scotch brite pad and smooth this out even more.
It's important to get this putty out of these nooks and crannies before it fully hardens.
Okay, and so now there's one dowel that's broken, so I've got to drill that out and replace it.
It's a quarter inch dowel, but I'll start with this 3 16ths bit and see if I can get it down
middle. Well, I think I got that 3 16ths hole right down the middle, so I'll just
move up a bit size, a couple sizes, but I'll get halfway to the quarter inch mark.
So now I've got that original quarter inch hole, and I can just run the bit down it.
Okay, I feel like I'm pretty close to gluing this back together, but then I realized
the crest rail is so splintery and it's a little loose there anyway, so I want to take
this section off and glue the crest rail back together separate. All right, that went together
pretty well, and so I think tomorrow I'll be able to glue the whole thing up. Okay,
I've let this dry overnight. Let's see what we got here. It looks really good here. I do have
some touch-up work to do on the back of this. This big crack across the back, especially here,
that must be where some of the splinters came out, but I'm just going to fill this with some
Fama wood, and we'll touch it up. I think I'll do that and these other scuff marks before I assemble
it. The front looks pretty good. There's just a little bit of the same type of thing right there.
All right, I've let the wood putty dry during lunch, and now I'll sand. I'll start with a little bit of
old 100 paper and then 150. All right, I've sanded all the repair areas with up to 220.
So now I think I'll stain it with some Van Dyke brown dye stain. The reason I use dye stain
as opposed to oil stain, oil stain you can put on here one shot and what it is it is,
and it would probably be too light. With the dye stains, I put on a coat and then if there's light
areas I can go back and add more stain and make it darker. I can make them as dark as I want.
Okay, I think I got everything. Drying time is about 45 minutes. I'm going to use an aerosol
shellac. While I'm waiting for the shellac to dry, I'll get these back spindles ready to be re-glued.
Okay, ready to do the glue up. You'll see that I clamped a board across the back of the chair
just to give me something to clamp to when I bring that crest rail down.
All right, that looks good. We'll see what happens. So I stained and shellacked this before the glue up.
Now I'm going to just go over it with a gray pad and then I'm going to spray it with a coat
of satin aerosol lacquer. When you're using satin or flat lacquers, be sure to shake them up. The
instructions say to shake for one minute. You should always do that. You don't want the flattening
agent to settle in the bottom and give you inconsistent results from this throughout the
life of this can. All right, there you go. Really nice reproduction chair. It fell over and the
crest rail broke right along here. It's all back together. Looks pretty good. I'm Tom Johnson,
Thomas Johnson Antique Furniture Restoration in Gorham, Maine. This is a little piece from a
table that I've been asked to reproduce. I don't have the whole table here. Someone just sent me
this piece. It's got these mortises cut in the back. They're at 90 degrees, which tells me that
this is from an apron of a Victorian table, the apron of the boards that go under the top,
and it's on the corner. So it's a decorative piece that goes on the corner. It's got this
carving here, this nice carving, which I sort of associate with Eastlake furniture.
I've got a nice piece of walnut here. It's on the lighter side, so I'll use
the lighter sections of this to make this. It'll be easier to match up when it's done.
So the first thing I want to do is rip my blank piece of walnut to this width,
and then I'm going to set up and cut these mortises.
Wow! I just realized I was getting ready to rip this board, and I took a second look at this thing,
and the grain's going this way. The grain's going the short way, so I don't need to rip it.
I need to cross cut it to this width. Now, off camera, I cut an extra piece.
Just to experiment for cuts like this, you need something to go by, so this area here
I've marked good to be my... I think it's the best spot. This is my extra piece.
Yeah, that's lined up really well with the inside edge of the mortise,
so now I can cut my good piece and then set up to do the other side of the mortise.
So now I think the next thing I'll do is cut these 45s on the back of it.
Okay, so now I'm going to route this cove in the outside of this. Remember, I've made two of these
throughout all these machining processes where I have to set up the machines. I'm going to make two.
I've also cut and drilled this block of wood, which I'm going to attach to the back of it,
to give me something to hold on to during the routing process.
You'll notice I also put double stick tape on the end of this block, too.
Okay, so the next step is to cut this little line on the perimeter here. I've got to carve it.
I've already been experimenting on my extra sample piece and was having difficulty getting around
this curve, so I've actually made a little template which I will clamp down to help me
get around that curve. And just a note here, I'm going to be doing some carving here. I am not a
carver. This is not a video about carving. It's a video about how I'm going to hopefully somehow
manage to carve these pieces. So now I've got to lay out what I'll call the compass design here.
Same thing, just lines. I've got to drill a hole. I've got to locate that hole, drill a little hole,
and then do these straight lines. Okay, I've got my hole drilled, lines drawn, but I realized I need
to lay out these little curly cues so I can define the ends of these lines. You know, one of the
great things about this piece is that the carving on the original piece is horrible, which is good
for me because it's going to give me a little bit of a little bit of room here. Even the curly
cues are really terrible. They're different sizes. I'm going to try to do a little bit better job.
Now I've drawn my lines for those little curly cues. I'm going to actually clamp my french curve
in place and use it as a guide. Right now I'll do the straight lines. I'll use a straight edge
as a guide. You know, clamp it down along my lines and just use the gouge to make the lines.
Okay, now I've sanded everything with 220 and I'm going to stain it. I have some stain here,
some light walnut stain. I experimented already on some of the scraps. I think it really gives
me a good background color. Okay, I've let the stain dry for five or six hours. The dry time
on the can says 30 minutes, but I gave it extra time because it's a little cool in the shop.
Now I'm going to brush on a coat of shellac and later this evening I'll probably put
off camera, I'll put another coat on and tomorrow we'll glaze it. I did put on a second coat of
shellac and let it dry overnight. Now I'm going to sand it, I'm sorry, with 500 really gently. I don't
want to glaze it with an asphaltum glaze. So asphaltum is exactly what it sounds like. It's
some kind of tar and I'll mix it into a clear glaze coat. I've already done that and I'll put
it on, try to recreate the distressing I see here. So I've mixed a little of the asphaltum
in some glaze coat here. The glaze coat is just a medium, it's thick. The kind I buy is
is extra thick and it's made just for this purpose, adding oil colors and things like that.
In this case we added the asphaltum and now I'm going to apply it to my little piece here. I will
put it all over the entire piece, wipe it all the way off and then I'll go back
and try to mimic what I see in the original, leaving bits here and there. Okay, my glaze
is dried overnight and now I'm going to just seal that in with some flat aerosol lacquer.
It's not really flat but it's the lowest luster that they have. Okay, the lacquer is dried. I
actually already unscrewed this and detached it from the block that was holding it. So here I've
made this piece for someone else. I'm not restoring this table so this doesn't match
this exactly but I'm not too worried about it. The person that's going to restore this will
finish up any color work that needs to be done but I think it looks pretty good.
