Howdy folks! Welcome back to Nomad Boat Building. My name is Mark Reuten.
We're back working on the Poulsbo Boat Project. Before final assembly of the backbone, I tackle a few important jobs: assembling the transom and transom knee, rough beveling the keelson, and laying out and shaping the stem bevels.
The Poulsbo Boat was a popular sport fishing boat built in Poulsbo, Washington during the 1950s and 60s by Roland Young using traditional carvel construction. My version uses cedar strip construction with fiberglass inside and out.
If you enjoy wooden boats, woodworking, traditional craftsmanship, and practical boat shop problem solving, you're in the right place.
00:00 Introduction 00:49 Marking the keelson bevel 01:45 Preparing for assembly 02:25 Sanding the transom knee 03:17 Glue-up preparation and taping tricks 04:49 Waxing fasteners 05:40 Two-step epoxy bonding process 06:47 Rough beveling the keelson 07:12 Using a shipwright's slick safely 09:25 Cleaning up with a smoothing plane 10:59 Mounting the backbone to the molds 12:32 Laying out stem bevels from the lofting 20:58 Final stem shaping with a spokeshave 21:29 Carving the maker's mark 23:39 Final backbone assembly 25:55 Gluing the stem into place 27:51 Fastener and alignment tips 29:19 Final fit check
AI Generated·May contain errors
Video Summary
AI Generated
Mark Rutan of Nomad Boatbuilding advances the construction of a Poulsbo sport fishing boat. This phase focuses on the precise preparation and assembly of the backbone, specifically the transom, keelson, and stem, utilizing a combination of traditional woodworking tools and modern epoxy bonding techniques to ensure structural integrity and alignment.
Hey folks, welcome to Nomad Boatbuilding. My name is Mark Rutan and I'm a wooden boat builder on
Vancouver Island. We are back working on the Poulsbo boat project. The Poulsbo boat was a
popular sport fishing boat built by Ronald Young in the 1950s and 60s in Poulsbo, Washington.
Ronald built his using traditional Carvel plank-on-frame construction. We're building
ours using a more modern cedar strip construction, fiberglassed inside and out.
In our last episode, we did a little bit of tweaking to some of the backbone components
and got them dry fitted for assembly. Now before we put that all together, I want to do a little
bit more work on those components. We need to assemble the transom and transom knee. We're
going to do some rough beveling on the keelson and we need to bevel the stem. All right, let's
get right down to it. All right, I'm ready to take this apart and get it ready for final assembly.
So one thing I want to do here is just mark my mark the keelson for the bevel that has to go
onto it. And so these planks are just going to float right off these molds and onto the keelson
itself. So I'm just going to use this batten to try and mark a line on the side.
All right, that looks pretty good. All right, I'm ready to start putting a few things together.
Before the knee gets fastened onto the transom, I want to take the opportunity to do a nice little
sanding job on it. It's already been sanded out to 80 grit or something like that. I might as well
take it up a step or two before attaching the knee and that way it just hopefully will save
me a little bit of work later on. Now I've been having some sander woes. There was a time when
I had a great little Porter Cable random orbital sander that was beautiful and then it finally
crapped out on me and I've never found a good replacement for it since. I think it's probably
time for me to get a professional quality sander. Price tag is high on those though so I'm kind of
gun-shy on choosing one over the other. If you have a recommendation, please let me know down in
the comments and if you know a sander manufacturer who'd like to sponsor a video, by all means send
them my way. I don't generally tape off when I'm doing a glue up but I'm going to do it this time
just because I want to try and keep things clean. I got this nicely sanded out. I just like
to not have to do a pile of work to try and clean up after I've done the glue up. You never want to
go right up tight to your finished line so what I usually do is hold back maybe a sixteenth or
something like that. Sometimes I'll even use a very small painter's trowel just a tiny little
rounded over tip and I'll actually trowel a tiny little fillet in to this joint
and when you peel it all away it looks really nice neat and tidy. Okay let's take this over to
the sawhorses.
Okay waxing up fasteners I like to use Clapton's beeswax because as I know the guy that makes
this stuff, my friend Roger, it's like a totally different consistency than most
furniture waxes. It's more like hand cream and so it's just easy to get it all over a
fastener and get a nice even coat compared to using a regular paste wax which is just
quite a bit stiffer. Now how Roger came up with this particular concoction I'm not entirely sure
like the white consistency is like this but he did it in collaboration with James Krenov
and the Smithsonian who were looking for a product that they could use on historic furniture that
would be, you know, archival I suppose you might call it. It's good stuff though I like it. I'm
using my usual two-step bonding process wetting out my faying surfaces with unthickened epoxy
and then using a little bit of thickened epoxy to ensure that we have a good solid
fully filled joint. Okay thicken this up with some mahogany dust. I'll put this joint together
with some temporary steel fasteners and then once the epoxy is cured we'll replace them with
permanent bronze fasteners. Using a washer there it is. I'm tooling up the joint with a little
artist palette knife that I mentioned earlier. Once that's done we can peel the tape and then
we'll just leave it alone. Beautiful. There we go that's all together with just a tiny little fillet
to make it look nice and neat and tidy. Okay leave that alone. So I've got the keels in here and
what I'm doing with this is I'm just doing a rough beveling of it. I've marked it off the mold and
I'm just trying to take away the bulk of the material just so it's easier to work on the mold
because there's a fair bit of volume of material to take off. Mostly I'm using my plane but where
I can I'm getting in there with my slick. Of course slicks can be equally dangerous as they are
efficient in removing material so you've got to be very careful about how aggressive you are with
them. Get a feel for the grain before you go too deep. Grain's working in my favor on this side.
The other side it was certainly not and the trick with a slick is you're using sort of short stabbing
motions. Some people like to pretend like you can take off, you know, paper thin shavings like a
plane. It's not what they're for. They're for hogging off material quickly and the shape of a slick
at the back of the blade has actually got a curve to it so that you can work flat in the middle of
the surface and the handle's free from obstructions and it gives you a lot of range of movement in
order to adjust the depth of your cut. There are slicks that are intended for just general
timber framing joinery that'll be straight and I have one or two of those and they work fine for
some things but nothing quite beats these. These slicks are specifically tailored to the
shipbuilding industry just like lipped adzes are. So I'm not trying to get too close to my lines.
I'm going to leave a very generous like 3 16ths of an inch or something behind
just to make sure I get it right on the mold. I love it when I get one of these big breaking wave
curls happening. So much fun. Then to clean things up, the smoothing plane is by far the
most efficient tool for the job. It's a short body and so it can adjust to the winding bevel very
easily. It's light enough that it's not too much of a chore to sling around. Now I would take it
further right down to my central line except that what I decided to do was pop this back on the mold
and after it's assembled, I've got a few backbone components, the skeg and the keel
that I'd like to just kind of do a quick rough assembly on even though they're still going to
have planking thickness in there to accommodate. I want to just try and make sure that
most specifically the skeg portion is over the curve and it's going to be easier to sort of
clamp it in place and try and get the fit looking about right before the planking goes
on to it. Then after the planking is on, I can make some small adjustments but the bulk of that
shape should be correct. All right, that looks good. Now I have one little problem in that I
need to figure out what to do about tacking this to the molds. I could put a screw right through
but I've got shaping that I need to do and I would normally put a little angle bracket underneath but
the way I did my bracing here between the molds kind of interferes with that which I hadn't really
thought about when I was setting that one up. Save that problem for another moment. That wasn't
much of a savings because that moment I was saving it for came just a moment later. Okay,
so I just use these little simple off-the-shelf hardware store corner brackets for
stuff like this. A piece of tape just so I don't have to get two hands into that tight spot.
Just use a little short screw into the keelson and a slightly longer screw into the mold.
That screw placement so close to the face of that station mold is going to come back to bite me just
a little bit much farther down in the process. Not in a big detrimental way but in a really sort of
dumb, annoying, fastidious way. All right, we need to lay out our stem bevels. The stem bevels we
developed them on the lofting. We do it by taking sections through the stem and we use the station
molds to tell us what the angles are going to be as the planks wrap around the molds and approach
the stem. Anyhow, so on my pattern here I've transferred all the marks from my lofting.
Saves me from dragging the big board out. So we'll take this information and we'll transfer it onto
the stem itself. I'm going to start by laying it out on the back and then we'll lay it out on the
front. You always want to work from a center line so I'm just going to pencil a center line in on
the back of this stem here. I often use a marking gauge for this sort of thing but this is going
to get painted and I don't want a sharp line cutting all the way through the back of my stem.
I'd rather it just be clean when it's done. I do however have a line deeply scored into the toe
of the foot here and up at the stem head so I always add some hard marks that are easy to find
later on. I'll do another one right here just to make sure that I don't lose them. I've done a
little bit of work on the shape of the stem here. Just want to check that I'm good all the way around.
I've got station marks marked on here, the various water lines, so those are important.
That's where we're going to lay off our information and what we do is we lay off a bunch of points
and then we connect the dots. Simple as that. In some cases the back of the stem will get affected
like down here near the near the bottom of the stem. I'm going to start losing some width but it
quickly grows to being full width somewhere up here. Somewhere around here it switches from the
back getting chewed into to a full back edge. I'm just going to grab what water line two looks
like to start with and I'm going to leave a fairly generous amount on here to work out
on the mold because I am a little bit nervous about the bevels because when you have bluff
bowed boats it can be hard to judge whether or not you're getting an accurate reading as you're
wrapping your battens around onto the stem. There's just a lot of change happening quickly
and I'm not super confident about how can I put it I'm not super confident about it
landing exactly right let's let's put it that way this one actually lands about here
it's funny how they uh yeah that's like right on the corner there it's like it just
goes wide and it sucks in tight right at the turn and then widens out a little bit that's all I can
do on the back now I got to go to the side side of the shear up here that probably continues the
same right through to the end draw that in pencil
something like that and it comes tucks in perhaps around the corner
it comes back out again so this is just going to get shaved off a little there's stuff going
on here that's actually hard to lay out so you know nothing else I like having a visual reference
of where I've got to go later on something like that better do the other side, too
so this line basically connects up with this line comes through and I need to
figure out this line and then we have a whole other one that's going to happen on the front here
should be mostly about the same on the stem face because we've got to make the uh the
planking the same width as our well the inside of our cut water so normally it's usually the
same width all the way through but depending on the approach the planking it can vary a little bit
I think this looks like it's all pretty consistent so I think I'll just run one line down the whole
thing this is a moment of laziness that's going to cost me later on I should have done a proper
expansion of the plank bevels at the stem face but I was underestimating just how bluff this
bow really was that's pretty good so the last thing I wanted to do is just revisit what's
happening in this section so that I can cut it down more accurately because I'm not real happy
with what I have a stem will have a winding bevel from one end to the other and you can cut that in
one shot on the bandsaw if you are willing to either cut freehand or if you have someone on
hand to help swing the tabletop while you do your cut but I don't like cutting freehand and I don't
have another person to help me out so what I do is just pick whichever angle is going to remove
the greatest amount of meat from my stem without me worrying about having to hit my lines on both
sides in this case it's pretty close to a 45 degree angle or something like that and I'll
just chop away what I can and do the rest by hand if you're liking these videos you can support me
by giving me a thumbs up throw me a couple of bucks or super thanks subscribing to the channel
turning on notifications and of course you can join me over on patreon find links in the corner
or down in the description my favorite tool for shaping stems is this veritas carver's draw knife
it's light it's easy to hang on to and manipulate and it takes a wicked edge now normally when I
laminate parts I'm working with veneers that were all taken from the same plank and I maintain the
orientation of those veneers such that they go back together the same way they lived in that
original plank in this case I was using up some old stock that I had around the shop
some veneers left over from the 2.4 meter project and the grain was different in every one of them
and that is absolutely kicking me in the butt right now as I try to do this shaping
and often you have to go with the flow changing directions or changing your approach in order to
overcome the obstacles of grain going in different direction that's just a normal carving practice
in this case though it's a little worse than normal so you just pick away at it as best you
can I'm using a gouge across the grain to try and overcome that in this little section of the stem
once the real rough stuff is over my next favorite tool is this old stanley
spoke shave this is one of the very first tools I picked up at a garage sale or a flea market for
five bucks it has been the biggest workhorse in my entire arsenal still got its original blade
still going strong it seems to conform to the shape of my parts better than any other spoke
shape that I have we got one more little detail to do on the stem before we're ready to assemble
it onto the backbone now not every one of my boats has got a builder's plate on it
but every one of them has got my maker's mark so we're going to carve that into the stem face
okay now that that carving is done this stem is ready to go onto the mold
this is all glued up so now we can permanently fasten it let's pop these out do that
there we go
I tape up for a fast cleanup around these guys so put a little tag on the end of your
tape so you can grab it easily I grabbed that one tag and it should pull everything
well at once okay that's ready to go onto the boat okay I need a couple
screws to put that together preferably screw it start with the wet out of course
now we'll thicken up the rest and do our filler coat so I'm going to use my shop made mahogany
flour for filling this one okay that should do it let's uh get this joint closed and then we'll
glue up the stem all right now I'm not sure what my best order of operations is here for this
quick grip okay my transom isn't fixed in place exactly I wanted to just get this joint
attached at the back end here and then I'll juggle the transom into its finished position
after I get this all set up I like using regular steel construction screws for doing these glue
ups because if you have to mess around with them if you have to take it apart mid glue up or
whatever these screws are resilient so you can pull them out and put them back in many times
without messing up the head compared to a silicon bronze screw which is a little bit delicate when
you're putting it in and taking it out plus because the bodies of these are so small I can
keep doing that over and over again without messing up the hole for the later fastener that's going to
go in there feels right okay okay so here's a trick for lining up to an old screw hole
you might have put into something use an awl feel for it I think I just want to quickly
check with a plumb bob that I'm on my mark
now I know I had a screw long enough just a minute ago throw those in for now
okay just mop that up the rag and we're done aside from a few fasteners that need to go in after the
epoxy sets up our backbone is done so now we're ready to move on to the next step so in the next
episode we're going to fair off the backbone and mold to make it ready for planking I hope you
join me for that I want to thank you all for watching and I especially want to thank all my
followers on patreon who make these videos possible if you can help support me on patreon
I really appreciate it you can find links in the corner or down in the description
all right folks we'll catch you next time