The MOST ACCURATE Bow Setup | Get rid of jitters, target panic, and bad groups!

LEARN ARCHERY
7 followers
6 Video Views·Jun 8, 2026
AI Generated·May contain errors
Hi, I'm Nate. This is Average Jack Archery, Pro Shopping Range in Phillipsburg, PA.
And AverageJackArchery.com orders $9.99 and up gets you free shipping to the lower 48.
Today we're doing part two. We had part one. If you missed it, don't worry, I'm going to recap it anyway.
Or you can watch it. There's probably links down below, maybe on the screen.
I don't know. I get lazy sometimes and forget.
We're actually here setting up with part two of the bow,
which is figuring out your peep height, getting everything officially established and getting to shooting.
No, I did not say tuning. I said get to shooting. I'll explain.
All right. So to recap, we are starting with just the bow at roughly the draw length we think it is.
For me, that's 31.5. This is an Elite Exalt LD.
So I have the mod I want here on here as well, which is a 75% mod.
It's what I prefer to shoot. Elite, you can do three different modules, smooth performance or 75%.
75%, I'm telling you, if you don't, whether it's target or hunting, you want to give it a stab.
I got my rest installed on here. I have my sight block.
I have my stabilizer bushings, my quick disconnects, but I don't have anything else on here.
And here's why. Again, recapping part one here. How many times am I going to miss my D-loop?
So what we want to do is we want to first establish what does our bow movement do?
So obviously I'm not shooting here. This feels very weird not having any weight on this bow.
But I want to feel what does the bow want to do? Does it feel like it wants to dip?
Does it feel like it wants to swing? I'm trying to figure out my draw length.
If it feels long and loopy, it is too long. If it feels short and jittery, it is too short.
In order to really see that, in case you're not wildly off, because that's going to feel pretty close,
you're going to go ahead and grab your sight. You're going to go ahead and mount it on here.
You're going to put it into approximately, if you're using the dovetail,
you're going to use approximately the distance you want to use.
Again, we don't have a peep in here. There's nothing inside the string at this point.
What I'm doing is, all I'm doing is just drawing this bow back and I'm looking at my pin float on a target.
I want to do this at like 8 feet. And the question is, does it seem short and jittery, like a gnat flying around?
Does it seem long and loopy? If it's long and loopy, it's too long.
Short and jittery, it's too short. We want to have a controllable pin float, again at like 8 feet.
Not a distance like this. Then we're going to grab stabilizers.
Before I mount stabilizers on the bow, I want to see what kind of bias it has.
So this LD with that sight, not shocking, and 99% of bows on the market, it's going to want to tip forward.
That's not as aggressive as it could be.
Yeah, but it's definitely going to want to tip forward. It's going to want to tip to the right.
So, a back bar is going to help alleviate both of those things.
But now, it's too much, right? Now I've got too much weight here on the back.
Obviously, this is a target rig, but the same rules apply if this was a hunting setup.
And I don't care if you shoot a 6 and an 8, an 8 and a 10, a 10 and a 12,
you really should be shooting a front and back bar.
I'm just going to be point blank with you.
You will never see a high-level shooter shooting without a front and back bar system.
It's just not going to happen.
And I'm not just saying like Bodie Turner, Levi Morgan, you know, those kind of people.
I'm talking your average amateur.
So here, now the bow is just resting here on my index finger and thumb.
It's got a little bit of a down tilt because we're now getting to the point of the show
where we're deciding where our peep location is going to go and how the bow is naturally going to sit for us.
So I should probably set my sight to 25 yards here because I'm actually going to start executing shots.
And notice I have not talked about building arrows, right?
A lot of people want to put the car before the horse.
They want to build the arrow.
The bow is the machine that sends the arrow downrange, and you're the person behind it operating the bow.
Those are the biggest variables.
This is just a carb and tombs and wingdings on the end, right?
This is about as static of an object as it can possibly be, right?
So it's going to stay at rest unless you make it not be at rest anymore.
So it can only really do one thing, which is fly through the air.
Everything else is you and the bow.
So figuring this all out first is way more important, all right?
So now what I'm going to do is now that I'm in this part of this stage is I'm going to figure out what the bias is of the bow.
And it does not want to go, right?
So if it's going to go this way, I have too much weight on my left, too much this way, I don't have enough weight on my left,
really far down, really high up, et cetera, et cetera.
I'm going to shoot this.
Just get that out of my way.
When you are setting up stabilizers for a hunting bow, this is going to be way less pronounced.
This is a 36 out front.
It's almost a 40-incher with the weights and the quick disconnect.
And I got a 15 out here.
It's really obvious when I move something out of whack.
With a hunting bow, it's not going to be as obvious, but you will, again,
if you can build a home base to go back to, meaning an angle that you like and a weight ratio that you like.
I like a one to three weight ratio to start for every ounce on the front, three ounces back here, okay?
Usually live between two and a half and three and a half by the time it's all said and done.
I think I run a 2.8 right now in ratio in terms of what's up front to what's in the back.
You'll be able to figure out what the float is and write it down.
Get a piece of paper or make a note on your phone.
Have an actual physical representation of what your home base is.
That way, if you want to play with it later, maybe you want to shoot a V-bar, shoot two bars in the back, whatever,
you have something to go back to later.
So how this bow is set up is I have a lot of drive in the bottom part of my hand.
So when it comes to gripping, that is not the point of this video.
When it comes to point of gripping, I drive a lot with the middle part of a really low risk grip.
It really puts my fingers high up towards the shelf.
And because of that, I actually drive this bow upwards.
So I'm really focusing on this kind of, this is very exaggerated, but this is how the bow ends up going.
So if I actually have too much weight in the front, the bow actually wants to continually drive down.
It's the exact opposite of what we want.
So I found with my tendency, I need to have more weight up front and cause that leaning down.
That's where I'm closer to not 1 to 3, but like 2.8, something like that.
I might even want to play with more weight in the front.
But then you get to a point where the bow is too heavy and you can't control it.
And I don't care how many reps you do, if the bow is too heavy to start, you're going to build bad habits.
You're not going to be building an accurate setup.
All right, let's cover peep height. Let's cover setting the rest of this thing up.
And yeah, I still haven't talked about the errors in tuning yet. Relax.
So for the sake of argument, we're going to pretend I'm not sighted in.
I have my sight set to 20 yards, roughly.
I don't have a peep in here.
I've been setting up this bow to compete with.
So yeah, I have a peep in here, but we'll talk about it in a second.
Also talk about why I have it tied in the way I have it tied in.
Again, targets at 8 feet.
What we want is we want to be shooting this as level as possible to figure out our peep as level as possible.
Think a Vegas shoot, Lancaster Archery Classic, stuff like that.
I don't want to be shooting down here at an angle.
I'm going to be shooting level. Ideally, it's around that 8 to 12 foot mark.
What I want to do is without a peep in here, I'm going to come find my anchor.
Whatever that anchor position is for you.
For me, it's the corner of my mouth, and then the peep just floats.
I'm actually going to wrap around here and make sure I'm watching everything.
And I'm going to shoot that a bunch.
And then when you get new strings or you get a new bow, not this little guy.
This is a peep tuner, not this video.
There's usually a little piece of serving in here, a little tag end.
With your sight mounted, you can take that little serving piece.
You can move it up and down.
What your goal is, is you're trying to find that little serving piece where it fits right into the center of your eyeball
the moment you draw back.
Don't throw a peep in here and then fudge with it later.
That little piece of serving is not going to gum up anything.
It's not going to cause a problem.
But you're going to draw this back, find your anchor,
and you want that little piece of serving to be right there in front of your sight housing.
And with that piece of serving right in front of your sight housing,
it's exactly where you want it.
Once that's there, then you can go to the press,
then you can put your peep in, and then you can fuss around it from there.
This is not a how-to-fix-peep-twist video.
Good luck.
Particularly if you're going to shoot something like a ham ski or a specialty, it's a barreled peep.
Godspeed.
We want to get our peep height, for me, at 20 yards.
If you're going to set up a bow for tack,
if you're going to try to go out west and shoot a mountain goat at 150 yards,
different story.
You might want to set it at actually a different distance.
But that 8 to 12 feet is going to be very representative of your 20-yard mark.
It gives you a place to focus your pin, moving that serving piece down
so it blocks off the center of the housing, blocks off the top pin, blocks off the single pin, whatever.
Goes right there, and then that's a good place to start your peep.
That way you don't have to be fussing around sliding up and down.
You don't have to be mucking up your string, cutting fibers, etc.
Once we have the peep officially established,
and we're just drawing this back, by the way.
Once you put the peep in, just drawing it back.
You then can tie around the peep if you want so it doesn't fly out so you can shoot it a bunch.
And that's what I would recommend.
Your peep inside the string is not going to move once it's tied around the middle.
It might move like a 64th, but it's not going to move like a full inch.
So you can actually put like half a dozen to a dozen shots in it.
Make sure that's exactly where you want it before you tie it in.
Now, the way I have this peep tied in is I just tie in all of my target peeps around the middle.
And then I tie an overhand knot on the top of the peep, an overhand knot on the bottom of the peep.
And then I have a tag in this way, a tag in this way.
I run a tag in through this bottom to tie a half hitch.
And I cinch it up into this side of the peep here.
And you can see I have a melted end.
Same thing's true on the other side.
I don't have anything on the top and bottom.
I would never do this with a hunting bow.
I want to always have those back serve ends pinching down the triangles at the other ends of the peep.
Because with a hunting bow, I really don't want it to move.
And you're never going to think about it.
With target shooting though, what I'm doing is here, because I just set this bow up,
I'm just making sure this is exactly where I want it.
And I'm talking 30 seconds to 60 fourths of movement here.
It's not a ton.
Then I'm going to take a silver sharpie or a black sharpie.
Probably black because it matches the rest of the setup.
And I'm going to mark right below the peep here on the string fiber.
And I'm going to mark above the peep right here.
I mean right above where the wraparound goes.
So I have a little bit of an air gap of white.
And if the peep does start to move, it will creep closer to that black or silver sharpie mark.
And it will close off that area of white.
And I know my peep is sliding.
I've been tying on target peeps like this for years.
Because I also sometimes need to pop in these peep tuners.
Again, different video.
And when you have the triangles in here, you can't do that when the bow is not in a press.
And sometimes I'm standing out here and not in my shop.
And I need to get a little bit of a peep tuning done.
So I just do that tie around the middle.
And with that half hitch on either side, it seems to hold.
Now some people run a bunch of half hitches.
They'll run a whole bunch of half hitches on one side.
And a whole bunch of half hitches down the other side.
I don't like that for two reasons.
One, it blocks off the coloring of the string.
If you're using an all black string, it doesn't matter.
But when you come to full draw and you're actually looking at your peep,
these two bottom strands are actually going to be in your line of sight.
And if one is solid black and one is solid white or green or gray or whatever color you have,
for me, it throws off how the actual ring of the peep looks.
It doesn't look right.
It starts turning into a cat eye shape.
I'm focusing on the colored leg and I'm losing the sight of the solid leg.
I just don't feel like I'm accurate left to right.
So if you are going to do that, make sure you do it down both sides so both sides are black.
Don't just do it around the one side or the other.
Also, the second reason why I don't do that is because removing those half hitches later is a gigantic pain in the butt.
Huge.
You need a little pair of side cutters.
You've got to clip each knot off one by one.
If you're a one-time string and then once you eat through the strings, you change your peep out, okay, that's fine.
But if you're continuously changing stuff or you change strings all the time and you need this peep back
or you want to move it later, please don't do the half hitches all the way up and down the sides.
It's a giant pain in the butt for your shop to do it.
Just don't get Western with it.
Tie it around normal.
Do the triangles top and bottom.
Learn how to back serve and you'll be just fine.
So we've got our bars.
We've got our sight.
We've got the peep figured out.
Everything is feeling good.
And now, we don't tune arrows.
Oh, my gosh.
Imagine that.
Everybody now at this point diverges into like 18 different directions.
Do I bear shaft in?
Do I spray foot powder all over my riser if you're Tim Gillingham?
I like my bow to be black, not white.
That's just me.
Although I totally get what he's doing with the fletching clearance.
I want to shoot the bow.
I want to get used to the bow and I want to feel this bow out.
I want to feel this bow out for like a couple weeks probably.
When I go and get ready for indoor season, which is unfortunately where I excel,
when I get ready for indoor season, I just live with the bow for a while.
I don't even put the bow through paper.
I don't bear shaft tune anything.
I don't paper tune anything.
I just get used to the bow because you're going to learn very quickly what the bow does and does not want you to do.
So, for example, I can tell you right now that this bow does not want me to have any ringside pressure,
which is my ring finger, which is the left side of the grip as a right-hand archer.
This does not want me pushing this way.
So I know that if I start doing that, I'm going to get some really weird left-right misses.
I know the tear through paper later I found out is atrocious.
So I'm actually really focusing on my thumb side over here and making sure I'm driving forward.
That bottom part of my palm, I'm driving forward with my palm.
When that bow goes off, the bow is straight forward.
There's no lateral torque to it.
I just know that is this bow.
But I wouldn't have known that if I went straight into paper tuning.
If you go straight into paper tuning with a brand new bow, particularly if you're trying to get it set up for extreme accuracy.
We're talking target stuff.
We're talking long-range distance hunting stuff.
If you're going to set it up for just y'all come 3D, classic 20-yard shots out of a tree stand, it's less important.
Go shoot through paper.
That's fine.
But if you're trying to build the most accurate setup for you that you possibly can, I really recommend spending time behind the bow.
Because what you might do in the first couple days or even the first hour with the bow, it's probably not what you're going to do in three weeks.
You're going to find what you like, what you don't like, what does work, and what does not work.
And I've just learned with this bow in particular that it does not like that.
So I'm going to make sure that everything that I'm doing here with this initial setup, with the peep tied in, is just me focusing on exactly how I need to grip this.
So once you're ready to actually start looking at tuning, the first thing you want to actually do is go and level all your sight accesses.
So it would be pretty obvious if everything is wildly off right here.
And you could do this when you're setting up your sight.
But again, I'm just trying to get the balance of the bow.
Notice I haven't brought up like I'm looking at my level.
I'm doing all sorts of stuff.
I've been at 8 to 12 feet basically this entire time.
Again, I still can shoot at 8 to 12 feet this entire time.
I want to actually feel how the bow is shooting.
And no, I'm not shooting groups at 8 to 12 feet.
But it's a 24-inch bale target, right?
Or some 20-, 24-, 36-inch bag target.
You've got plenty of room to move around dots.
So you're just trying to focus on aiming and how the bow holds because you're building accuracy here.
We're not trying to just jump out and attack next weekend.
So I'm shooting the bow.
I'm getting used to how everything is functioning.
I'm getting used to what I do wrong.
So deliberately push things weird.
Change the grip out a whole bunch.
Push more with the top part of your grip.
Push more with the bottom part of your grip.
Wrap your fingers around the front.
Do the curl over like I do.
Really, I'm only touching with the first two and a half fingers.
My pinky is nowhere near the grip.
Try all of those things, okay?
It's not the time now to try new anchors.
It's not the time now to try new drawlings.
You've done all that.
And that's, again, what I was talking about with finding a home base.
If you want to change any of these things at this point, remember, we're building accuracy here.
If you want to change any of these things at this point, you've got to go back to all of the steps,
through all of the steps, back to that point.
So if I want to say, okay, I'm actually going to play with my stabilizers.
I've got to go back to stabilizers, forward.
If I want to go back to changing drawling, I've got to go back from drawling, forward.
I don't just want to change drawling because it has the ripple effect.
And now everything might feel different.
The weights might feel different.
The angles might feel different.
I'm not saying they are, but it is a good chance they will.
And then you're right back to square one in terms of building your accuracy with that bow.
And now you've kind of reset your clock a little bit.
So I know that you'll see a lot of people, myself included, have set up bows in five minutes.
Everything's shooting a perfect bullet hole. Everything's great.
We're wadding them out to 50 yards, yada, yada, yada.
In reality, all of your top-level shooters, both in the hunting and the competition side,
know what they're doing now because of all these steps that they've done for 15, 20, 30, 40, 50 years.
And if you want to start those habits, now's a good time to do it.
Go back to step one, or go back to the first part of this video, or part one of this video series.
Read through all that, watch through all that, and do the recap here.
But now getting at this point where you're watching the pin float,
and you're watching what your tendencies are and what your tendencies are with the bow that you're currently shooting.
It may or may not be the tendencies of the bow that you shot already.
Or, heck, it might even be you've got fresh strings on your old bow, but you want to try something different.
Again, you have to teach an old dog new tricks eventually.
Dogs do change.
Now, there's no need for me to make a part three of this series,
which is paper tuning, broadhead tuning, all that sort of stuff.
I've got a ton of videos on that already.
They are down in the description below if you're interested.
But, I mean, truthfully, the comments from last video on making a part two were so overly resounding.
If you feel we need a refresh on part three, which is paper tuning, broadhead tuning, and distance tuning,
I guess drop a comment down below. We'll make part three.
But anyway, I need to get to making sure my peep's in a good spot.
We've got a couple of tournaments coming up.
The second leg of the RBD here is just in a few weeks.
We've got the PA Clash for Cash, TACS at the end of the month here.
So, lots of great stuff is happening in the state of Pennsylvania in the month of May and beginning of June.
And I hope your state and your area is also having a lot of really good shoots,
both at the national and state level, and you should attend them.
You really should attend them.
This is where the rubber meets the road.
You want to talk about all the tuning and everything, all the bow setups and whatnot.
It doesn't mean squat if you don't actually put it into practice.
And how you put it into practice is you put it into practice under high-stress moments.
And this is great.
And, yeah, there's a camera here, but this is not high stress.
My heart rate has stayed below 60 probably this entire time.
And that will change drastically when money's on the line, when you travel and go somewhere,
when other people that you may or may not know are watching you shoot at the stake.
I'm not saying you need to go to a national-level event and shoot an open pro with Levi Morgan.
You're going to get your teeth kicked in.
But you should go.
You should go and shoot your local tournaments.
You should go shoot your state tournaments because it will put all of this to the test.
And you can shoot in the hunter class.
You don't need this, right?
If this doesn't interest you, that's great.
That's fine. Go shoot your bow.
Go slap your stubby stabilizers on there.
I say stubby in the most loving way possible.
But go shoot a hunter setup, right?
Just go do it because that's where you'll find where all this tuning effort gets put into play.
It really does.
And also, you will meet a lot of really cool people.
You'll have a lot of fun. I promise.
I have more fun, relaxed fun, in tournaments than I do practicing in my backyard.
I know that sounds stupid, but it's true.
Anyway, that's all for this video.
Again, if you want part three, I guess you can comment down below.
We'll make it happen.
By we, I mean me.
And I hope you're able to get outside.
Enjoy the sport of archery.
Archery and hunting, if you so choose.
Definitely enjoy God's beautiful creation.
Get out and shoot your bow.
I promise.
It's a lot more fun than sitting inside complaining your NHL team lost.
Go Penguins.
We'll get to see you next time.
