I Restored a Designer Teak Coffee Table!

Trash To Treasure
3 followers
I'm using Mohawk toners and lacquer to try to save this mid century coffee table. This Swedish built designer piece was found in a thrift store in pretty rough shape and despite the stains and scratches, I knew it had potential. I had to order a part for it from the UK so the project overall took longer than expected. While the outcome wasn't *perfect*, I'm quite happy with it, and it lives with us now.
#furniturerestoration #vintagefurniture #furnitureflipping #midcenturyfurniture #furnituremakeover #coffeetable #transcendfurnituregallery #diy #furniturerepair #furnitureflip
I randomly found this teak coffee table at a Habitat for Humanity restore a couple of years
ago and it's been in my storage room ever since. Now to some people this is just an ugly brown
beat-up coffee table, but to those who love mid-century furniture, you may see more here.
This does have some finish issues. There's some dark staining, a lot of obviously gouges and
scratches, some areas where it looks like there was tape, some chew marks, and I have a sneaking
suspicion that at least the top of this may have been refinished before. I actually ran into a
little hiccup with this and had to order some parts, so it's taken me a while to get this done,
but let's get to work. My name is Angie and I refinish furniture. Sometimes I paint and
sometimes I don't, but I always do what I can to save old pieces from the trash.
Welcome to my workroom. So this piece has solid wood components and veneer areas. The leg assembly
is entirely solid wood. It's solid teak. The trim pieces along the edge are also solid teak. This
beautiful wood grain you see here on the underside is a veneer. Obviously the top is a veneer and
then there's pressed wood in between. This piece was made in Sweden by the furniture maker J.O.
Carlsen, but it was designed by Karl-Erik Axelius, and I'm hoping I'm saying that right. I'm not
sure how to pronounce it. So here's some issues. This support bracket is completely broken,
and you can see someone has written in marker that would not be original to the piece. So that's one
of the reasons I feel like this has been refinished, and also you can see some drips here,
and these drips are not from food or some beverage that was spilled. It's actual polyurethane.
There's also some damage here by these little locking cams, and the combination of the broken
support and the cams that have come loose, and you'll see there's actually one that is broken.
That's why the leg is starting to pull away from the rest of the table. These supports are solid
wood, and I'll have to have a good look at it. If it is a clean break, I might be able to glue this
back together and have it hold up. When you have two wood surfaces that don't have any holes or
bumps and they fit completely tightly together, using wood glue there is often a stronger bond
than the wood itself. So hoping I get lucky with that. I'm just gonna pop these off. You can see
there's actually supposed to be three of these cam screws in here and a couple of dowels. Here's
where you can see that pressed wood substrate. This was a very common method of manufacturing
in mid-century furniture. I have done a lot of mid-century pieces of varying qualities. What
people don't realize is that a lot of the high-end stuff is pressed wood. It is just what they used
back then. But looking here at the edge, this is a great view of just how thin that veneer is, and
that's why a lot of first-timers go at these pieces with an orbital sander with too aggressive
a grit and they just blow right through the veneer. Even modern-day furniture is made with
this style of fastener, but this size is almost impossible to get around here where I am. I'm not
sure exactly what this metal is. I'm 99% sure it is toast, but I'm going to try to press this back
together and just see if it can possibly be twisted back into shape, but yeah, I don't think so.
This was the piece that I had to order, and the only place I could find it in this specific size
was in the UK. Amazon carries tons of these, just not this size. It was about a two and a half to
three week delay while I was waiting for those to come in, but that's okay. That gave me time
to work on the last piece you saw. Not everybody has their own style and way of making these repairs.
This is what works best for me when I have pressed wood that I need to epoxy back together.
Wood glue is not really going to work here. You want a very strong epoxy. I just take a blade and
cut out a little section from each side. You don't want too big a wedge or it's not going to go
together properly. You just want to make sure that there's a nice clean area where you can
inject or push in some epoxy. I'm adding in as much as I can, being careful not to get it in
the actual hole. This stuff dries very hard and I'd have to re-drill the hole. I'm going to add
that in and clamp it down and just let it dry overnight. I've done this fix many times with
pressed wood and it turns out really good. The key though is clamping pressure. If you don't
have enough pressure to hold it flat, it's not going to dry flat and then you're up the creek,
as they say. What's interesting about the support brackets where they are broken,
you can actually see glue residue. Somebody tried to do this once before and most likely
wasn't using the right amount of glue or didn't clamp it. There's no point in using wood glue on
anything if you can't clamp it. You have to have that pressure and of course the type of glue
matters. I've seen repairs done with what looks like school glue or crazy glue and there's
so many different types but you really have to have the right type for the job. Basically anything
that I don't want to ever come apart again, I will use wood glue on. Some joints that may need to come
apart later on, I tend to use hide glue which is more easily reversible than this wood glue.
Before I let these set up for the rest of the day, I just want to make sure there's no glue
in this glue hole. Okay, now it's time to deal with these legs. These are solid wood but you
can see these are made from several pieces of solid wood. I'm just making sure before I go
any further that these are all sturdy. You can see those drips there that I was talking about.
These are kind of a mess actually but it is nice and solid so that's good. I don't have to make any
repairs here. While the other two brackets are drying, I'm just going to sand the veneer on the
faces of these and yes there is a veneer on these. They're not solid teak like the legs are.
This piece is pretty filthy both from its past life and also sitting in storage for a couple
of years. The finish on this is quite thin so I'm actually just going to be sanding it off and I
don't often do that. I save it for very specific occasions. These legs are solid wood so I don't
have to worry about sanding through a veneer and in the time it would take me to put stripper on
these, get it all stripped off, I could already be completely done sanding. With a fine grit by the
way, not a coarse grit. Now from afar when I was applying the Odie Safer solvent you were probably
thinking, oh wow that actually looks pretty good. It actually doesn't up close. There's a lot of
finish issues here and this is kind of a good example of why I'm not a big fan of products like
Restore-A-Finish in every situation. It's kind of a band-aid. Like I just put clear liquid on this
and made it look so much better but it's not better it just it's an illusion. Restore-A-Finish
works great on pieces that have a little bit of surface damage but as soon as you have scratches
and gouges and chips that are down to the raw wood, that's not a candidate for Restore-A-Finish.
That's either spot repairs or full refinish. And I've seen the effects of using, I don't want to
pick specifically on Restore-A-Finish, there are other products like that where people will just
throw some oil on something because it temporarily makes it look good just like I just did there.
But when the finish is not intact and there's damage it can actually make refinishing harder
down the road so using these products you just have to know what you're working with
and it shouldn't be your go-to. It should be reserved for specific situations.
Once I am finished with all of the flat sections I'm going to grab one of these sponge pads
and what this will do it will allow me to sand the rounded profile here without actually damaging it
and you don't need one of these foam pads you can carefully do this if you have great hand eye
coordination and skill with a sander or you can hand sand it but you can see how quickly this
goes with this pad and no harm is done to the original shape of the legs which is important to
me. Now that is so much better. I'm going to do the same thing to the other leg except this time
I decided to pull these out they just unscrew just to make sanding around them easier and then
once this one is done I will add some Odie's Safer Solvent which is just going to help clean
everything up in preparation for finish later on. Once I have my initial 150 sanding done I'm going
to go in with a 180 and basically do the same thing and I'm going to be applying lacquer to
this. Initially I really wanted to do Odie's oil on it but once I had this all sanded down and wiped
some Safer Solvent on it and could see the natural color of the wood there was kind of too much
contrast there for me for this specific piece so because of that I'm going to be using a vinyl
sealer some toners and then lacquer and now you will see how much better this piece looks with
just a clear coat versus before when I just did it over the old finish and that is the difference
between products like Restore Finish and just throwing some lemon oil on something versus
taking the time to properly refinish it and again that's only for pieces where the damage has gone
completely through the finish into the wood. If you've only got a couple of light surface
scratches and there's no damage to the wood some oil or Restore Finish is fine.
So the underside of the table has the maker's mark and it's quite light. I need to sand the
bottom of this. I honestly could have just cleaned it and left it at that but when I redo things I
like to kind of redo it all so I just put a piece of painter's tape there so that I don't accidentally
sand over it because it's not very visible. Alright let's deal with this top. There are
some issues here that are apparent right away at looking at it. You can see the discoloration from
what was the Habitat for Humanity Restore sticker. Obviously hundreds and hundreds of scratches and
marks. There are some rings that you can see on there. This looks like they had tape left for a
very long time and then pulled it off but there's some strange things for example this area here.
This looks like a finish that kind of got splattered. It's very plastic feeling and I'm
pretty sure someone at some point put a polyurethane coating over some existing damage and you see this
ring right here. Rings on furniture are not uncommon but normally once they've penetrated
through the finish and into the wood they turn black. You see dark rings. These ones are white.
White rings are usually damaged in the finish itself but you'll see here that's not the case.
But first I've started to switch to my scraper just because this whatever coating they put on
this is a bit thicker and I don't want to spend so much time sanding when I don't have to.
There's a couple things going on here. First of all like I said the ring itself is white in the
wood which is very strange. Normally it's dark in the wood. You can also see the area around it is a
little bit darker and there's not as many scratches there. So this is what I think happened. I think
they had some dark rings from a water glass and I think they tried to sand it out and even bleach it
and when you use a bleach or something like oxalic acid on just a stain you run the risk of this
happening where it will bleach out the stain but then it's too light and that's why you see
refinishers that will apply oxalic acid to the entire top and for someone just starting out that
doesn't make sense. It's like why would you do it on the whole top when you're just trying to bleach
out a stain? This is why. It's not every single situation. Sometimes you can put oxalic acid just
on a stain and it's totally fine. This is one of those instances where it's not. You can even see
how it almost looked like there was an oil there at some point. It's darker and that's not finish.
That darkness around the ring there, that's not excess finish. That is some sort of oil product
that is in the wood itself. I also discovered some dark spots at the other end of the table which you
couldn't really see with the old finish but once I stripped it off they were apparent so I am going
to be doing some oxalic acid on this. You can see there are also a lot of cross grain scratches
but they're not quite deep enough to warrant steaming them out so I'm just going to do a
sanding here with 150 grit and I'll finish with 180 grit and that's as high as I'm going on this
table because of the finish that I'm doing. But first I'm going to add some oxalic acid to some
water here. Oxalic acid is a wood specific bleach that targets things like water stains.
You know it's a little bit tough to see when the wood is bare but right here, right there, there is
some sort of weird dark stain. The oxalic acid is hit or miss on teak for some reason. I don't know
if it's the oil content in the wood but I either have really good luck with it or I have no luck
at all so we'll see how this one goes. Now the oxalic acid is not going to do much for this
area that's already been bleached but in order to prevent the same thing from happening when I
use it on the dark stains I have to apply it to the whole tabletop. Oxalic acid needs to be rinsed
really well so I'm actually doing two rinsings. I'm going to wipe off any of the excess water
and then let it completely dry overnight. Now I know this doesn't look too bad while everything
is raw but as soon as you put anything on it it's going to darken up and you'll still see that
contrast with the white rings. Same with the dark spots. You can sort of see them here. It's not too
bad but as soon as I put anything on it it's going to pop back up again. Unfortunately the oxalic
acid didn't really do much to remove those dark spots but I had to give it a try and because I
need to do some touch-ups here and some color work and toning I'm hoping that I can just blend it out
with those products. Now that this is all sanded and cleaned and ready there are three products
I'm going to be using. I'm going to start with Mohawk Easy Vinyl Sealer and one of these paint
can handles to make spraying it a lot easier and I'm going to be sealing this piece in the end with
Mohawk Pre-Catalyzed Lacquer. Now if you look over here you can see a bunch of different toners.
These come in lots of different colors. I'm only going to be using one color on this
and that color is Perfect Brown but first I need to seal the work that I've already done
and then everything else will be on top of that working in layers. I'm just showing this part
here because I often get people that say that they buy handles and they don't fit. They are
not super easy to put on but yes they will fit. These handles really make spraying large areas
so much more comfortable for your hands and it gives you a better result. When you're using
lacquer you also want to make sure that you have a respirator on hand or even better on face and a
few tips for spraying. You want to make sure that you keep the can far enough away from the piece.
If you have it too close you're going to get drips and runs and you also want to sort of
dance with it in a way you want to sort of sway back and forth so that you have a uniform
consistency all along. You want to aim for about a 50% overlap so that means each time you make a
pass you're covering about half of the old pass and as with most things that are sprayed on
furniture more light coats is better than fewer thicker coats. You can see I'm standing in one
spot but I'm moving my arm the entire length of the table. If I were to just stand in one spot
and just move my wrist I would have inconsistent spray patterns and that's no good. I'm going to
be doing two coats of vinyl sealer on this and then I'm going to start on my color work. I do get asked
fairly often why I choose to use lacquer and spray cans when you can buy it in bulk and use
something like a HVLP spray gun and the reason is up until very recently I did not have a compressor
which is needed to run those. Although I do have a spray gun, it's a Wagner that I have used for
paint in the past, I prefer to keep that just for paint. So now that I do have a compressor I'm going
try to find a good quality spray gun that I can use just for spraying lacquer so that it saves me
money and not going through as many cans because that kind of bothers me a little bit. I'm going
to be adding the same vinyl sealer to the legs. Although I don't need to do repair color work on
these legs you'll see once I put this on that we've got a couple of different tones of wood
here and normally I embrace the natural variations in the wood but with what I want to do with this
I need things to be a little bit more uniform. There are a few different ways that you can do
this. You can use pigments which work quite well, certain types of paints. I could have tried a
stain but that would be quite tricky to do in such a specific area. I'm going to be adding
toner lacquer over this whole thing before I do my final seal coat. So what I need to do is I need to
basically re-add the wood grain to the areas that have been bleached out. This doesn't need to be
perfect right here, all I need is for it to be closer and the additional coats of lacquer and
toner will help blend this out. So this is the color change after one foggy coat of the perfect
brown toner and the reason I'm okay going a little bit darker is that these pieces were often made of
rosewood. This one's not, it's actually teak but I do like a darker color in this case. So I'm going
to be doing one more what I call a foggy coat. Basically what I'm saying is I'm not super close
to the table, I'm just sort of fogging the color on. Toner is very easy to get blotchy if you're
too close to the piece so I like to do several very thin coats from a good distance. You get a
much more even consistency. This is a piece that I'm going to be keeping and it's going in our
living room where we have a lot of darker woods like walnut so I'm okay with this being a little
bit darker. So I'm finally able now to start with my coats of lacquer. I believe I did a total of
five or six coats. Now you can see on the right there that little dark spot, that is where that
dark area was and that's just gonna have to be as good as it gets. These tack cloths were an amazon
wishlist gift from a viewer named Jamie who actually sent me a bunch of goodies so huge thank
you to you Jamie for all of these things I can't wait to use them. If you've actually sent me
something over the last few months and you haven't seen it in a video yet don't worry I did receive
them. Some of the things on my amazon wishlist are quite specific so I can only use them for
certain projects but until I can do specific shoutouts just consider this an overall thank
you to everybody who's helped support my channel in any way over the last two years. So this is
where I'm at with the legs now after two coats of the vinyl sealer and you can see here I am going
to be adding some toner. I normally don't mind variations like I mentioned earlier but some of
these pieces in fact even some of the same boards will have areas that are very dark and very light
and I just need to try to get this to blend a little bit better. And the difference between
boards is actually really pronounced on this particular leg assembly and look at this board
you've got very light areas and it gets darker toward the bottom. So because of the style that
this is and the look that I'm going for I'm not going to literally make it all the same colour
I just want to bring it a little closer together. And here's where you can see what I'm talking
about it's not all identical in colour but the tones are definitely closer and I'm happy with this.
With these I need to make sure that they're going to stay in place and often when these
come out it kind of destroys the threads but all of these except for one were very tight when I put
them in and the one that wasn't all I did was add a little bit of epoxy and then screwed it in
let it dry and it was totally fine. I need to make sure that these are facing the right direction
there is a point where there's an opening and then you turn the screw and it closes the opening
and locks the cam into place but you won't be able to actually insert it in unless it's pointed in
the right direction and these little pieces do have arrows on them so that you know what
direction it needs to be in. They're actually really neat fasteners. I'm testing these the
whole way along especially the two pieces that were repaired the ones that had broken but I think
now that the cam fastening system is fixed that it will put a lot less stress on these braces
and they're just going to sort of work together much better and you can see there's no movement
there at all this is rock solid now so I'm super happy with how this came out. This is the cam that
I ended up having to replace so I'm just making sure that is in right and it's like I said turned
to the right direction and then I can insert this side. If you remember initially there was a big gap
because these were not set properly and they weren't fitting quite right but everything is
nice and tight now. Well for you guys this has been a half hour journey for me it's been about
three weeks just because I had to wait for those parts but I couldn't be happy with how this turned
out. There were a few issues like with the staining on the top that I had to sort of work around and
to do so I needed to make this a little bit darker than it would be naturally but I'm okay with that
like I said a lot of these pieces were originally done in rosewood for some reason this one is teak
but I don't mind that it is a little bit darker kind of more like rosewood. Thank you so much for
watching as always and I hope you enjoy the reveal. See you next time!
