This thing had mildew all over it, a TON of scratches and dings, water rings from decades of glasses (and no coasters), and was nearly destroyed from a THICK gross layer of built up furniture waxes and polishes. Don’t use consumer spray polishes on your furniture! It’s a nightmare down the road when refinishing.
This is a fairly typical but designer Danish teak dining table, a mix of solid wood and veneer, by CJ Rosengaarden. In excellent condition, this piece could be worth several hundred to a thousand Canadian dollars in my specific area to the right buyer. The veneers on these are pretty thin, so I only have so much room to work with. Is it perfect now? Absolutely not. But despite the flaws that remain, I think this table has a long life still ahead of it.
To say that this teak table was in rough shape is definitely an understatement. It's been a little
while since I've done something quite this bad. There is a lot going on here, there's a lot to
fix. But the first thing I had to fix was actually the mildew on it. I had to spray it down and wipe
it clean before I could even put it in my car because I didn't want to get that anywhere inside
my vehicle. But I got it home and now it's time to really have a good look at what I'm dealing with.
This is your pretty typical solid teak mixed with veneer. We've got solid teak around the edge,
mahogany veneer on the underside, solid teak legs, and of course the top is a teak veneer.
This is the leaf. Doesn't look like it's had a lot of use but you can see there's some scratching
here. I'm not really sure what caused that. We've got water staining rings, what looks like it could
have been a bleach or some sort of solvent stain, scratches, dings. Stay tuned. My name is Angie and
I refinish furniture. Sometimes I paint and sometimes I don't but I always do what I can
to save old pieces from the trash. Welcome to my workroom. Okay so I have four teak chairs. Now
these did not come with this table. These I've had in storage for quite a while. Aside from the obvious
damage here to the vinyl, I think this is electrical tape, there is significant damage to
pretty much every joint on every chair that someone has horrendously tried to repair. Aside from
putting these mending plates, some chairs have screws driven into the back of them which are
not original and despite all of this they're still wobbly. Of course it's not a proper fix.
I'm not going to cover the chairs in this video and I'm not 100% sure if I want to sell them with
this table but they are going to be in an upcoming video. They're going to be pretty difficult so wish
me luck on that. So as with any furniture project I'm going to start by taking everything apart.
Now for some people this part isn't necessary. I'm taking all of this off because I like to
refinish the bottoms. Usually it's just a matter of a light sanding and sealing. You can see that
the manufacturer almost never seals the bottom of furniture but I like to, especially on a dining
room table, it helps seal the underside from any spills that might drip over the side and kind of
up underneath and it just looks so much nicer. Now I'm just doing a couple of test scrapes here to
kind of see what finish I'm dealing with. This leaf hasn't seen as much use as the rest of the table
which is very common in dining room tables. I do believe this is the original finish although it's
not super thick so it's definitely not conversion varnish. It might be like a danish oil. So I'm
checking all the joints to make sure everything is tight and as you can see this edge bending here
is loose and it was loose on pretty much every section that there was edge bending.
But here you can actually see the pressed wood in between. These tables fool beginners all the time
usually because they do a pretty good job of hiding the pressed wood. Now why did they use
pressed wood to begin with? There's a lot of misconception about it that it's only in lower
end furniture. It's not. It's in a lot of higher and mid-century pieces as well. It was a nice
stable flat substrate to glue veneer to and it allowed exotic woods like teak and mahogany to
stretch further. You can get more out of a log if you turn it into veneer than solid wood. This helped
keep things affordable for people and avoid some of the issues with solid wood like cracking and
stuff like that. Now I could have used something like contact cement to re-adhere this. I've had
really good luck with this glue with solid teak. Teak is a bit of an oily wood so some glues don't
hold up very well but I had really good luck with this one and this is actually waterproof as well
which I think is important on a dining table top. This kind of glue does need to be clamped. I'm
opting to use some tape here instead of a clamp just because it's such a long span. I'm gonna
tape this up really well set it aside to dry and then I can get to work on the underside of the
main table. I'm gonna make sure to mark where everything is just so when I go to put this back
together I'm not second-guessing myself. Every hole has to line up so this is just a lot easier.
Mahogany is a wood that tends to darken over time. You can see the original color of the raw
mahogany underneath where that assembly was. Now looking at this section here, to some it would
appear that this is solid wood and it's true that it is all wood but it's not one piece. So we've
got teak veneer on the outside, mahogany veneer on the inside just like the rest of the table
and I'll snap a couple of photos here so you can see a little bit closer. We've got the mahogany
veneer on the inside, solid wood in the middle, different type, and that thin little bit of teak
veneer on the outside. And same thing here just another view, mahogany, solid wood and the teak
on the outside. So that is how thin the veneer is on these pieces and it's why a lot of beginners
kind of don't always have the best luck with them because it's so easy to sand through the veneer.
And I mentioned earlier when I was scraping the top of the leaf that the main table had a totally
different kind of finish on it and I think what happened here is that it would have initially
had that same sort of danish oil finish, just fairly thin, but it looks like there are decades
of built-up furniture polishes, something like pledge or some kind of waxes that just have built
up over time and dirt gets ingrained into them and it starts to look dull so they add more. And
you'll see exactly what I mean when I start to do the tops. Now on the solid wood trim pieces and
the legs I'm going to do 150 grit, on the veneer I'm going to use 180. So the middle part of this
half of the table, that edge banding was loose as well. But there's another problem, there's only
three pins and there's four holes so they lost one somewhere along the way. So I'm going to snap
a picture and see if I can find a replacement. In the meantime I will put the rest in and re-glue
this strip. Just like the last one, glue on each side and tape it up to clamp it. Once the glue has
had time to set on all of these pieces I pull the tape off and use the scraper to scrape off the glue.
Because there's veneer on both sides of this I don't want to try to sand through it because 100%
I would sand through the veneer. As mentioned I'm using 180 grit on both the veneer on the bottom
and the top. On the bottom here I'm not going for perfection, I'm literally just doing a really
light sanding so that I can seal it properly. I'm not worried about getting every little mark out.
The underside of the main table has some glue spillage from where they attach these solid trim
pieces to the veneered pieces. It's super brittle so I just use my scraper to remove any of the
excess. No one is ever going to see this, it's just one of those little things that's going to make me
happy. What doesn't make me happy is what happened to this top. So like I said, you can see a huge
difference in what I'm scraping off here versus what I was scraping off on that leaf. The finish
there was quite dry and powdery and the finish here, not so much. It's really thick and it's
quite physical trying to scrape it off but look at this. If I take this and squish it together
it stays squished. This is years and years of using waxes and furniture polishes improperly,
not cleaning them properly and it just builds up and builds up. So I mean honestly there's no
surprise that this actually had mildew on it. It's going to feel so nice to get all this gunk off this
table. Now this section looked like it's been cut with a knife. I don't know if they were literally
cutting things on it or if some kid was just messing around but those cut marks are unfortunately
right through the veneer so there's not really much I can do about that. They're not even wide
enough to get filler down into them. As the finish comes off you're starting to see more and more of
the damage that I have to deal with and you can see here I cleaned it up pretty well. I wanted to
give it a test to see just how bad it was going to be. In other words, to see if there was going to
be any wax build up on the sandpaper and you can see I only sanded this little bit and if I stop
this and bring this a little bit closer you can actually see the wax build up on the sandpaper
just from that little area. Once you get even one of these little spots built up, let alone a whole
bunch like there are here, your sandpaper is pretty much useless. I'm going to show you how you can get
rid of that and keep using the same sandpaper but for now I have to do a better job of scraping.
There was still a little bit of wax residue. Another thing that can sometimes happen especially
if you're using a finer grit like this is you'll get areas where the dust will build up. Now the
sandpaper I'm using here isn't made for this machine. The holes don't line up exactly so I'm
getting more build up than I normally would but this little block will get rid of wax residue
and it'll help clear away excess sawdust and this is going to help extend the life of your sandpaper
and save you money in the long run. You'll see me use that block a couple times here as I'm going
along. You can see the dust is super fine and yeah it just allows me to keep using the same
sandpaper a bit longer. This area on the left is where the damage is. You can see there are some
water rings and some areas of dark staining so I'm gonna have to use oxalic acid on these tops.
This wouldn't be my first choice because I have a table leaf. Now what happens often with tabletops
where the leaves aren't used that much, the tabletops will fade over time or lighten with
certain woods and the leaf will stay dark so I'm gonna have to use oxalic acid on all three pieces
including the leaf to hopefully try to get these a little bit closer in color. There are rare
occasions where I would suggest using oxalic acid only on dark spots. Generally it has kind of a
negative effect and you end up with light patches so it is recommended that you do it over the whole
top. This is hotly contested in the furniture flipping and restoration world. Everyone seems
to have their own opinion on that. This is how I learned to do it and this is how I think it should
be done. There's this one corner where the teak is a lot lighter than the rest. Now obviously
natural wood is going to have a lot of different tones and variations but this one corner is just
so much lighter than the rest so I'm not going to put oxalic acid on that because I don't want
to lighten it any further. This is that area that was really cut up. You can see it's minimized a
little bit after sanding. Obviously the veneer is so thin I can't sand too much and the cuts aren't
really wide enough to put some filler in so they're just going to have to be what they are.
On the inside here I just did a very light sanding similar to the bottoms. I just need to clean them
up enough to put some sealer on it. On the outside I'm taking a little more time but again that
veneer is super thin so I'm just doing as little as possible here. The legs however are solid wood
so I'm initially hitting them with that 150 grit. The legs didn't have that same weird build up as
the top did so this was a fairly quick and easy process. Okay so this is after the oxalic acid
has dried but it's not rinsed yet. You can see it did lighten some things and not others. There's
some smear here. Don't worry about that. That will wipe right off. Those super light areas initially
are still light. I'm going to rinse these off and just see how this is going to look.
I've already kind of resigned myself to the fact that this is probably not going to be
perfect. Those of you who've been following me for a while know that that's difficult for me
but sometimes with these pieces, especially veneer that's very thin, that's just kind of
the reality. There are quite likely going to be some cuts and dings and marks that remain.
Once all three sections have been rinsed off and have dried overnight, it's time to sand.
My first sanding was with 180 if you remember. I'm going now with 220 and then I'm going to finish up
at 320. This grit is going to depend on what you're using for a finish. With the Ori's oil,
you can go as high as you want with grit and you won't have any issue with bonding. So you can see
a few marks here still remain. I'm just going to have to get over it. This middle section looks
like it should be flipped upside down but it can't be flipped upside down because of the way
that the pins are and the pins were put in obviously by the manufacturer and it's how this
lines up. If you look closely, you can actually see how the colors kind of alternate. Top, bottom,
top, bottom. So it was built that way and I just have to get over it. So if this color looks
familiar, it is because it is a leftover stain from one of the last projects I did. That cornerstone
oak table or whatever it was. I had a little bit left over so I just added some more super duper
everlasting oil and a little bit more solvent which is going to dilute this a little bit. Now
this looks really brown and it's the same thing that I said with the cornerstone oak. It's not
going to be that dark when it goes on. So I just did a little test here on the end of one of the
legs and you can see it looks like an aged patinaed teak color. So this is going to be absolutely
perfect. The reason I'm opting to use a stain and this is honestly the first time I've ever stained
teak. Normally you don't really have to. If there's any color matching to do, I tend to do it with
toners but in this case I'm choosing to use this one because I have it and I don't want it to go
to waste. But also it's going to help kind of unite all those different tones together and
I'm hoping it will help camouflage some of the damage that remains on the top. Now this does
have odies oil in it but because this is a table, after this has dried for a couple of days I'm
going to go in and use some odies oil just by itself on top just for some added protection
and then I actually end up using another layer on top of that which is the odies wood butter.
And together this is going to give this, at least I hope, a beautiful almost patinaed finish even
though it is a brand new finish. Now even though this has pigment in it, it goes on the same way
as any other odies. You put it on, let it sit for a little bit and then buff it off. The stain
mixes that I do, I usually buff off right away. Anywhere that there's just plain odies oil and you
can see here I'm putting it on the underside. This is just the plain super duper everlasting oil.
This I will leave on for a couple of hours and then come in and buff it all off. Now again this
isn't necessary. You can see that even the manufacturers don't do it. I personally think it
looks beautiful even though no one's going to see it. I know that it is sealed. You know sometimes
with dining tables people spill stuff. I would hope that everyone is using coasters but you know
that's not the reality and sometimes things happen. So the more of this that I can seal up
the better it's going to be. So once that is buffed off I'm going to go ahead and put this back
together. I did clean this mechanism up a little bit and I added a little bit of lithium grease
just to help it slide a bit. It's still a bit stiff which makes it a little bit tricky for
one person to pull it apart but two people can do it super easily. And these legs had nothing on
the bottom so I'm just adding some plastic caps here just to kind of help slide this around.
People could put felt pads on the bottom if they wanted. I just didn't want the teak at the bottom
of the legs to get chipped by vacuum or shoes or anything like that. So looking back at the
underside this is what it initially looked like and this isn't the official glamour shot but you
can see the bottom is absolutely beautiful now. Doesn't really matter to anyone but me but I think
this looks great. So I'm adding that second layer of the Odi's oil on top now. I'm going to let this
sit for a little bit and then buff that off as well and follow that with the Odi's wood butter
which has a little bit of a higher wax content. Right now all three pieces have the Odi's sitting
on it and yeah then I just buff it all off. This is a part that a lot of beginners with Odi's oil
kind of not mess up on but they don't sometimes grasp how much buffing it actually is. You have to
get all of the excess oil off to have a successful finish. So just a quick recap of some of the tools
that I used here. I used my Baco scraper. I used oxalic acid on the top. There were a few little
areas I had to patch some holes and I used this Timbermaid wood filler in the color red oak
actually. This is that block that makes cleaning your sanding discs a lot easier and you can get
more out of them. This little tool is great for putting in nails or things that are hard to grip.
I used Titebond 3 wood glue where I needed to and this is the grease that I put on the table
mechanism. That stain that I had left over was a mix of southern pecan and aged bronze pigments
with some Odi's safer solvent and a little bit of super duper everlasting oil. My second layer was
just super duper everlasting oil and my third layer was the wood butter. A few little areas
that I had to do really small touch-ups and I used these Mohawk brush tip markers in the color
honey maple, honey spice, and light oak. So overall I mean especially considering what I started with
I can say that I'm pleased with how this turned out. Over the moon maybe not so much because like
I said there were a few marks that I just couldn't get out and you'll see them in the reveal but
hopefully I've disguised them enough that it's not immediately apparent. I think it's fairly
reasonable to expect vintage pieces to have some of that history that even when refinished remains
on the piece. Let me know what you guys think down below. As always thank you so much for watching,
enjoy the reveal, and I will see you next time.