NEW EVERYTHING (Arrow Saw, Components & Arrow)

Defending with Past Crossbows
3 followers
4 Video Views·May 4, 2026
NEW EVERYTHING (Arrow Saw, Components & Arrow)
Comments are disabled for this video.
What's up guys welcome back to the channel. Today we're going to be building some
X10 Parallel Pros from Easton and I'm testing a new saw that you're going to want to check out
and we'll see if it's legitimate. We're going to go over the new four millimeter components that
Easton's offering, build some arrows, bring you along. Here we go. So I ordered these 300 spines
the GPI is 9.5. You see that it comes as shafts, no nocks, no components. So the rest of that is
up to us which I kind of like. First things first is we need to put a nock in it. I'm going to run
the IP4 from AEE and then we're going to hit a measurement to figure out where the half out sits
over because again it's going to slide over. Get that measurement, pull the shaft back, take into
count that half out hangover and get a mark. Cut them. We're going to show you how to square them
and we're going to show you how to spin them so that you can get them aligned just so perfectly
so they're as true as you want them and the more details you cover usually the better groups you'll
see down range. Let's go. So this is the Easton 75 grain. It has a aluminum steel combination.
It's got this little orange o-ring type thing to help make sure that it's square and center
and lined up. Basically it's a half out with a built-in collar. There's several different options.
We'll go over all of them down the road in this video but for now we're this is the one I'm
probably going to run. So we're going to check the filament. Looks good. Let's silver sharpie right
there and pull this off and see how much that takes up. Pull that out. You guys can tell we made
a silver sharpie mark and measured it. Five eighths is what we need to keep in mind when we mark this.
So I'm going to throw a knock in, grab my bow, pull it back, have my little assistant. Lovely.
Mark this arrow for me so we know and I want to cut this thing as short as possible because it'll
increase the stiffness. It'll also make it so that I can shoot a faster projectile. I like to run my
arrows as short as possible. IP4 knock like a glove. Mark about right in the middle of this shelf
and whatever you mark I got to keep that in mind as far as the half out sticks out five eighths.
Does that make sense? Okay thank you Jeff. So guys so if I'm going to cut right there remember
this is going to end up being about there which I should be able to get with because you marked
it right down the middle. If you didn't mark it down the middle and you marked it closer
you'd have to account for that five eighths. So just know that this goes slides over the arrow
and again out of everything when it comes to components in my personal opinion some sort of
collar is what's going to help you resist impact failure, impact damage. That's where the weakest
spot is on the arrow and obviously Easton knows that and their engineers thought of this. So
we're going to cut it right there. Let's get a measurement on this and so I'm going to take the
knock out to do all my cuts and I strongly recommend that you do all your cuts carbon to
carbon no knock in. Let's go check out this device here. This is called the ModSaw. They sent it to
me to do a video on and test. I think it's important for you guys to know that when somebody
sends me something I did not pay for it. But I also told them I'm free to say whatever I think
about it and they said that's cool. So when it came out of the package it was just in a box like
an arrow box and all these little doodads were slid up in here. So it's kind of a modular system
hence the name. I'll just walk you through some of the things. This is your saw. This is your power
button. This is your dust cover. This is where you'll put your power source in. Right over here
you'll want this guy to be about eight inches away. So eight to nine inches. Right here the
blade will be going this way. You'll be spinning your arrow that way. That's important. So the arrow
will be held here and then there's an indicator here to give you the exact distance. I know my
arrow is going to be somewhere right around 25 and a half. They all slide in this groove. You just can
loosen and tighten. So I'm tightening them up right now. Over here which is part of the process is
these bearings. These bearing posts slide up and down so that you can spin your arrow. And then
right here we'll get you a close-up but there is a wobble indicator. So you'll be able to put your
arrow when you're done cutting it. I'll show you guys and I'll be able to square it against this
sandpaper. The sandpaper will you can turn it so that you don't just like square all your arrows
on the same piece of sandpaper and they get provide replacement stickers. So this threads
out and you can put a new little circle sandpaper. I don't know the grit. I haven't done an arrow yet.
This wobble indicator is super cool because what I'm going to do is I'm going to cut them. I'm
going to square them and then I'm going to put the eastern component on. Not glue it in. I'm going to
screw in a broadhead, probably an iron will, and I'm going to spin it with that black line indicator.
And if I see any wobble, which we will, I will just move the whole component broadhead a quarter turn
and I'll just keep doing that until I find where it's marked where it's not wobbling and I'll just
use the sharpie and that's where I'll hot melt it in, which is pretty cool. And then from there,
this little guy, I just slapped it in. It's got a thread for a screw so I'm going to screw this down
to the wood and then at the very end here there's two more holes to screw it down
and I'm going to do that right now. So this will just keep it pretty stable.
Good. She ain't going anywhere. And right here.
Okay, so we're tight. We're good to go. Now, here's one of the coolest features. Right over
here is an inch and three quarter hole and you can attach a shop vac to it, which I'm going to
bring my little shop vac cord up here. See how it fits. I don't care if you use duct tape, whatever,
but when I turn the saw on I'm going to turn that shop vac on and suck all that nasty carbon dust
into the shop vac and not have a mess on our hands. It should be pretty cool. I think that's
creative. He did provide me with a replacement blade, but he made it sound like this blade is
going to be really tough to wear out, which we'll find out. Without further ado, this is the Mod
Saw. Let's cut a dozen arrows. 25 and 5 eighths. Beautiful indicator here. Let's see what that
looks like on our line. So we're going to be here and you can see I'm giving myself a little bit of
real estate there. Probably could go a little shorter like advertised. I think we're going to
stick with that. So this blade is going to go this way and I'm just going to hold the arrow in the
grooves here. Again, remember we're about eight inches from the blade with this post and then I'm
going to spin this way while the blade goes the other way. Hopefully that makes sense. On the
first one I'm not going to turn the shop vac on. I want you guys to hear how quiet this saw is.
Are y'all ready? So there's our arrow. We're just going to put this on real quick.
Slap this on before we cut any more arrows and just make sure I didn't royally screw up.
How's it look, Jeff? How much real estate? We've got plenty of real estate. I could have cut it
shorter, right? Yeah. Okay, I'm going to take advantage of that information and I'm going to
cut it shorter because I want to make this as light as possible and the current arrows I'm
running are eastern axis long range four millimeter match grade. That's a mouthful
and they're at 9.4. So I really want this arrow as light as possible and I could have gone to 340
spines but generally I spine down just to be safe. All right guys, we went with 25 and a quarter.
Saw is on. Everything's tight. I'm going to do one more check because we have a dozen of
these to cut. Hopefully I didn't get too greedy there. Perfecto. Beautiful. We're going to cut
them and then we'll come back here in a second and we'll show you our squaring process and then
we'll geek out on all the components that Easton came out 2024 which will be cool. Pull that out.
Rest in peace to that o-ring. It's already gone. They're probably not meant to be doing that but
it's all right for the video and just for SMGs, let's weigh this arrow without anything on it yet.
So 236 plus a knock plus a 75 grain component. So here is your saw. This is your battery bank.
This is where the power goes in. This is going to be where you're going to square your arrows
so you can loosen this tab and rotate. Inside here is your sandpaper basically and you can
kind of keep adjusting it or screw that take it all the way out and replace it with brand new
sandpaper. These are the bearings. So you have an arrow spinner right here. When it's time to
square these arrows which were at that step now I'm going to loosen and I'm going to put this
all the way up against and tighten. Pretty easy to use and that'll help us get a good square.
This is like I said eight about eight inches from the blade. This post will help stabilize the arrow
as you cut it. Right here is a middle peg. This is kind of like the center balance point to just
keep it sturdy. You got your measuring tape and then down here this is your other bearing. It slides
as well. It's modular. You can loosen it and slide it just to accommodate your arrow size and then
right here is the end piece where your arrow will go. Take your knock out and there's a little
indicator to the exact measurement will get you a tight of that so that you are precise and these
tighten and loosen. So give me a top view of that and a top view of this close black line. I'm going
give you some light. You guys can tell I silver sharpied all the way around here and I'm going to
sandpaper the silver sharpie off. You don't have to do that. I like to do that. I'm going to loosen
this and slide it all the way against there. I'm going to sandpaper or rotate the arrow. I got my
sandpaper tight and I'm going to spin the arrow this way. So right now I'm squaring after we cut.
It's a very important process. Kind of nice this is all in one. I didn't have to buy a separate
tool like from G5. I just silver sharpied it and I'm just getting off the little silver sharpie
making sure it's really square. The next step will be to spin test it with the components we're going
to use. That'll ensure no wobbles. We'll do it with a broadhead. I'll show you. It is awesome.
This is just a couple steps you can take to really ensure that you're making your arrows the best
they can be. These are X10 Parallel Pros. They got rid of the Pro Comp. Basically they just
migrated to this. So this is like a high strength fiber bonded to a 7075 alloy. So you kind of got
carbon and aluminum. This is the arrow that wins all the tournaments worldwide and you can cross
over and hunt with it. It's got the tightest tolerances when it comes to spine. So that's
kind of what you're getting for when you invest in X10 Parallel Pros. I'm definitely going to
give them a shot. I might hunt with them. I'm definitely going to go with these or the
Eastern Axis Long Range. So the cool thing, made in USA and I don't know any other arrow
company that can say that. Made in America. All right guys, so now what we're going to do is
we're going to set this up where I can go here. Nice. And then what I can do is show you guys
I'm going to spin test it. If I don't like it, I'm going to take it. I'm going to rotate
the arrow right here. That's definitely wobbly. So then we take this and we spin it.
All right guys, so we we've done a lot at this point. Let's finish building this arrow. So you
see I silver sharpied. I need to hot melt this bad boy in. So we're going to go ahead and pull
it out. So we're going to hot melt with the no more torch. Makes it too hot. No more gas. We're
going to go back to the old electric heat gun. We're going to crank it up. This is the 75. So
what we're looking at is mostly aluminum with the steel right here for your collar. The 55 grain,
all aluminum. Hence the weight. The 100, mostly steel with some titanium. 100 grains. I like the
materials. And then you have the 150 for maybe you traditional or maybe some guys that are like
heavy arrows. 150 all steel. So we're going to heat this bad boy up. Try not to melt your silicone
o-ring that centers it. Oh yeah. Like a glove. That's arrow elegance. That's arrow magic.
That is a sense of pride. Like you're doing everything you can to make your arrows money,
we elected to use the 75 grain, four millimeter half out option from Easton. Again, we hot melted
it. That allows us to index. We indexed, made sure our arrows were spitting true. So recapping,
cut them with the new mod saw. Then we squared them. Then we did the wobble test and made the
adjustments. It's pretty good steps. So here we have this all set up. This is mostly aluminum
with a steel collar, all in one system. The 55 grainer again is all aluminum. The 100 option
is steel with the titanium collar, which is a great option. And then the one 50 all steel,
hella heavy y'all. If you're into that, that's totally cool. You have the option. We're going
to throw the knocks in. These are the IP force from AEE huge fan. Need a couple Nick from AEE.
I'm getting low. Hint, hint. You got my credit card on file and don't recommend that. All right,
let's get this fletched up. We're not going to run a wrap on this one. We're just going to go
straight up to white. AE hybrid HP is high profile. Yes, I buy them by the 500 and a yellow,
no primer pen needed because they're hybrids. Let's get them fletched. Yellow will be my
and then we'll get a weight on this bad boy. It's a good looking era.
Slot this bad boy on. Let's get a total airway. Look at that. Okay.
Four 63. And then if I elected to run this 55 grain half out, it'll drop us down to four 36,
which is a pretty good spot too. So I don't know, man, I didn't want to be in the four 60s. If I'm
a little complainer right now, I'm kind of complaining because this area right here is
what I've been running and shooting consistently. And it's at four 47. If I'm going to run two site
tapes, it's going to be because there's a significant difference, but I can still do
that. We'll see the X tens are obviously the best arrow in the entire world. So it's up to you guys
to see if like what you want to run. I definitely want to test them. If I'm shooting tighter groups
with the X 10, uh, I'm probably going to roll with it. Uh, the titanium is what I'm running
right here on this half out East and still makes that. But if you want to do this new sweet collar
system, you're going to have to go with aluminum to stay at the same weight or bump up to that
aluminum steel, which is what I elected to do. And if you're not worried, bump up to that 100
steel and titanium combo or ball hard and go one 50 all steel. So guys, that's my new arrow build.
We introduced you to the saw. We're just doing a little tinkering. Figured you guys would like
this. Maybe you learn something separations in the preparation. We'll catch on the next one.
