http://www.VideoJoeKnows.com How to repair a damaged bathroom door....Part 7 Is your bathroom (or bedroom door) damaged & you're not sure if there's any way to make the needed repairs?....or you're not sure how & what steps to take in order to make the needed bathroom door repairs? You're in luck then! Take a look at this quick instructional video & see if your bathroom, or bedroom door is damaged in this way that "joe" shows. If it is, watch "joe" as he is preparing an entire instructional video series that shows how to repair a damaged bathroom/bedroom door, for your enjoyment, entertainment, & education. Hey even if your door is not damaged in this way, I'm sure there's something that "joe" will say or show you how to do, that you could use for future use. This is Part 7 that "joe" will show re: how to repair a damaged bathroom door. Hey if "joe" can repair a damaged bathroom door, so can you! http://www.VideoJoeKnows.com
Here's my liquid nails I used the other day. Now here's a tip for you too. When you get done
using your liquid nails, your tip is always full of the remaining liquid
nails. What I usually do is I'll squirt out a little extra and create a little knob on there
and then the next time I use it I can grab that and usually it'll pull out a little bit
inside. You may have to clean that or whatever but that's what I tried to do on this time here.
It didn't really work too well this time only because that knob was only on there for a couple
days. Sometimes I can do this to clean it a little bit but if this whole thing is hard you
may have to cut this tip. You may have to cut the tip back further and dig some of this out
to get to it. That's the only thing I wish they would really figure out how to make that better
so that two months from now you can still use the tube with the tip on here. Maybe unscrewing
the tip or something like that you could clean that out or something be ready for the next go.
I don't know it's just a thought I had. All right I'm ready to use that now.
Making a little mess aren't I? I didn't have any craft paper with me today. At least I got a vacuum.
Always make sure you clean up after yourself. Before I use this I always like to squirt a
little bit out make sure that everything's going nice so I don't get a hard little goody into my
work surface you know. Okay I think I'm ready and these tubes sometimes I've got the pressure
undone at the bottom end of my caulk gun but sometimes it still wants to bleed.
So always have something ready a cloth a napkin paper towel whatever because you may look one
second and set it down and then you you come back afterwards you know a couple minutes later
and this is all dripped down onto your carpet or your tile floor your linoleum or your countertop
wherever. So be careful with that and I know they have some caulk guns that shouldn't do that now
when you press the button it stops but usually what you're going to find on most caulk tubes
of mastic such as liquid nails when you first open it it's under pressure
you know you're going to have a lot there and so some of it's going to bleed. When this tube
and this is a brand new tube I've hardly used any okay but once you get down three quarters
halfway whatever you're less likely to do that. So always be aware of that when you're using a
brand new tube. All right let's see what we're going to do here. I'm just going to put on a little bit
this is going to kind of bond that top surface too. Let's see and now I can I can just use my putty
knife uh-oh last time I used my putty knife I used it with the liquid nail I got it on my putty
knife so I gotta man I should have checked that first because I want to I want a sharp clean
edge because I got to make that smooth shoot I got a couple minutes before that liquid nails
skins over wasn't ready my loss is your gain always make sure something like this you're ready
now see I put my I put my uh my putty knife away before the liquid nails was dry on there
and I couldn't clean it off it's easier to clean off your putty knife after your liquid nails dries
on it okay so that's what happened with that okay now now I can just that's all I'm gonna do
I'm gonna have to decide when I'm gonna stop on this you know here I see I can just go right over
it like that because I've got the masking tape there I think I gotta put on a little bit more
that was too much but I can wipe it off not too concerned where that where the masking tape was
okay that's smoother so if I don't have a clean edge to go on it leaves a groove
so I just have to be careful with that I gotta clean off my uh putty knife edge just a hair
the putty knife wasn't ready I was trying to do it too quick
you know you're working with just a little bit it skims over yeah I'm gonna have to clean
off my putty knife be right back let's try that again we'll put a little bit more on there
just getting it off from the tip of the gun like I said you don't want to play with it too much
after that's about it now if I wanted to I'm gonna try this getting my finger wet
just putting a little spit on it and knocking down the edge do that with your finger
it doesn't stick see you did that with a dry finger you all get out there's something else
you can do too you can just you can just get your tip of your blade wet you know with a damp
rag or something and just kind of go over that you know and that helps it slide a little bit easier
after you get the liquid nail on there like I say you're not really going to use liquid nails
you know for caulking but in this case we are now would be a good time to fill this in remember
the open pores just on the style the edge of the door from here down see how that's rough that's
the edge the cut edge and that's exposed all the wood grains to moisture we don't want that
because it cracked there before here we got a little hole there remember and I'm doing this
because we got the door down I'm just gonna flatten that out that now that's cleaned up the
pores man that dries I don't think any water is going to affect the bottom edge of this door
anymore what do you think it's like we got a nice little mess going on here at this point
I think I'm going to take this masking tape off in case it leaves a little edge I want the
liquid nails to have an edge you know if there is I might have to wipe that off a little
see if you didn't have the masking tape down and you'd have a big mess going on
I don't look too bad it's like there's a little bit of an edge we have to
see if I can just wet my finger or something just blend that in
all along where the masking tape was you didn't know you needed to be an artist
when you were doing repairs huh you know you do what you gotta do to make it look right
sometimes it's an unconventional way how you're gonna do that right such as this
all right I've got to let that set some more now and I'll come back
and do a light sanding of that I can't sand that and I don't want to paint that yet because that's
the the paint's not going to take to that plus I want to I want to slick up the surface a little
bit and a little bit of the sanding edges the paint's going to stick better to it and I'll get
a nice job hey when you do patches do all the steps and do it right I'm gonna do this freehand
and let's see what happens I'm just gonna put a little liquid nail just over that surface
before I do the painting because I did the other liquid nails on the other side and I'm just
putting a light skin just over that rough edge or that exposed edge because that was the
hardboard remember that's just gonna help before I do the painting a little extra right there I
might have to have to clean that off could I could have put masking tape on there but
you know there was such a little bit of mount there I thought I would see what happened
I just did it freehand that's good I do the touch-up paint the touch-up
paint is going to roll beyond that edge okay beauty