How to Fix Rusted Garbage Disposer Made Easy?

VideoJoeKnows
61 followers
470 Video Views·Apr 20, 2026
How to fix rusted garbage disposal made easy is what this DIY howto video is about. VideoJoe is working away on a rusted garbage disposal that is rusted stuck stuck stuck. Can he fix a rusted garbage disposal? Find out! Watch & learn as VideoJoeShows you what VideoJoeKnows...how to fix rusted garbage disposal made easy. Nice!
Yeah, there's a lot there's a lot of rust down and I'm gonna have to take that out into the garage get it underneath some
Better light. I don't want to do it here and mess up the floor or do anything like that
Plus I've got to clean that and keep dumping it out and tapping on it and all that kind of stuff
But I'll get her. I'll get her
Okay
Hang tight
I'll show you what it looks like when I get done. Oh
man, I
Tell you I I'm pretty sure I got I got most of it and
What did I end up using to clean it? I I've got a hacksaw here and
The tip was cut off and I could go in there and dig on it and then between the drum
Between the drum and the outside of this
Well, it's the outside of this and the inside, you know, it's not any thicker than
A hacksaw blade and so I just kept going in there and then I would put it in there just
beyond
Just beyond and then I would take my wrench
and turn it
like that
And get it in there a little bit and the teeth of the hacksaw blade
Would would start taking off
the rust and then I
Didn't know it but there's teeth two teeth on the inside and then down underneath
Down underneath the cutters. There's two more down here. I never knew that and
so I took the hacksaw blade in here and
I I turn this
back and forth
back and forth and
Little by little I got
Pretty much all of it and come to find out these these two blades in here
I think this is an old style and the blades used to not
twizzle around
100 360 degrees
Some new ones you can reach in there and the whole thing turns, but these I think are stationary
And it's fine because the cutters up against the edge and then there's another one out this way and the other sides the same way
Okay, and and so
You know, I kept turning this back and forth
See, there's nothing now
that's because I got I've got that a little bit of gap all the way around it and
I was gonna I was gonna spray some some WD-40 in there
And I still might I could I could still do that
When I get it installed
When I get it reinstalled, you know, I could if I wanted and I haven't I haven't plugged this in yet
Should I plug it in? I'll plug it in. I've got to turn this one light off first
Okay, I think I think there's still enough light in here. Now when I plug this in that thing's gonna turn
You know, so I have to keep my hands out of the way and stuff
Okay
Maybe maybe I'll do it like this
Let's see
All right, babe
Let's see. Maybe
Maybe I should spray a little
WD-40 in here
Like that
Tip it upside down. I don't want to get WD-40 all over the place, but
Let's just see
That's running. It's running
Pretty smooth there, I would say
Try it this way. I
Got it on and I'm gonna spray
Look at that
WD-40 can came off
All right, I just broke that thing, okay, here we go
That's that now after I get it installed I can spray some WD-40 down there I can also
Periodically make sure to run it right make sure to run it and
So it doesn't so it doesn't get rusty again
I'll just have to I'll just have to be aware of it, right?
Down the road if we want to if we want to start using it a lot I
Might have to encourage my wife to use it every once in a while or I'll just go by
Every couple weeks run the water and turn it on to make sure it's working, right?
The worst case what's the worst case scenario if it rusted up again?
do the same thing or
You go and replace it now these things cost
last time I checked
There were about 150 bucks and like like I say, there's lots of different ones
this this happens to be a half horse power and
they have they have them all the way up to
One and a quarter horsepower, I believe it is
Okay
And so you'll just have to decide
On your own you go to the store. You're gonna have sticker shock
okay, and
Incidentally if yours ever goes out and if you want to replace it
You know, you can replace it
Just like that. You don't even have to take the
The old piece that hangs off of your sink
You don't have to replace that if you don't want most of the time this will the new
Trim piece will fit right on or as you saw the other piece came right off of there the new the new badger
garbage disposal
Put that same piece on hook it up there and away you go. Do you see what I mean?
You could always do
Something like that if you want it
Then you you just don't use the rest of it
You know that part is 25 30 bucks, though
so
If yours is all scratched up
You might want to go ahead and replace it
All right. I think that's it. I'm gonna go hook it up now and I'm gonna hook it up the same way
I took it down. I'm gonna clean up the threads
And I am going to install
some some Teflon tape and
I can actually do that right on these threads right here. Just install the Teflon tape
clean off
clean off the
Marks make sure I don't have anything on there put some Teflon tape on there and I should be good to go
Put it back up
