http://www.VideoJoeKnows.com How to fix a loose & rocking toilet is easy, when you know how. "Joe's" got to go on another service call to check out a loose & rocking toilet, & to figure out how to fix it. Do you have to be a licensed professional plumber to fix &/or repair your loose & rocking toilet?....I hope you know the answer to that one by now! Loose & rocking toilets can be repaired & fixed by you....by "joe"! Are all toilets created equal? No. All loose & rocking toilets cannot be fixed the very same way....but if you watch this video series, on how to fix a loose & rocking toilet, I'm sure you'll be able to re-secure yours. Is there anything "joe" can't do?........ah! Remember, if "joe" can't do it, he won't show it! http://www.VideoJoeKnows.com
I tell you, I got another service call to go to.
As it is, does Joe have a nut on his plate today?
Of course I do.
But that doesn't stop people from calling me and I'm going to fix it for this guy too.
He's called me up.
He's got a vacation condo and he wants me to go check it out.
He's got a toilet that's tipping and a kitchen faucet that's dripping.
No joke.
Am I a professional plumber?
No.
But I can look at his toilet, I can figure it out and I'll be able to fix it.
What about the faucet?
Have I ever fixed this problem before?
Probably not.
But I'm going to look at it anyways and I'm going to show you the different steps that I go through to fix something.
And you know what?
If I can do it, you can do it.
Stick around.
You might learn something.
This toilet looks pretty good.
I'm not sure what is exactly wrong just yet.
You remember the report was that this toilet was tipping.
Tipping?
What are they talking about?
Tipping.
From side to side it looks pretty good.
Sometimes you've got to sit on the toilet and check it out and see what's going on.
And sure enough, it's tilting to the back when you get off.
See, it moves just a little bit.
And I can see there's a little gap here.
When I'm not on the toilet, I push down on it and it pushes back down to the caulking line.
That means I'm going to have to take these bolts and tighten these bolts.
There's some caps here.
I'll show you how to pull those off in a minute.
But that looks easy enough.
Let's get to it.
All these to remove that cap.
Well, not really.
But these are different things that you can use to pop this cap.
Because if that cap is really super tight, you might have to take a really thin putty knife and wedge under there.
Or a little bit thicker one.
I've even got some little tiny screwdrivers.
Maybe I can wedge that underneath there and lift it just a little bit.
Then use a bigger screwdriver and pop it off.
See, I can't get this big screwdriver under there.
And I don't want to start hitting that with a hammer and bend that and mess it all up.
You know what I mean?
Just take your time and figure out which tool.
And like I said, you might need a few things.
We'll see if we can pop that up.
It should be easy enough.
That cap has been on there for at least eight years that I know of.
Okay?
So just be careful with those.
Because you want to reuse those caps and snap them back down.
I want to try to keep out of your way.
I'm not generally left-handed.
But I'm going to try to do this with my left hand.
So I'm not in your way.
I think I'm going to try...
Yeah, see that putty knife?
It's not doing it just yet.
This one's a little bit stiffer and thicker.
I think I'm going to try one of these little thin screwdrivers.
Let's see if I can't...
Wow!
Jeez!
Wow!
Man, that's on there.
Mercy me.
I think I got it just barely.
I'm going to put another little screwdriver under there.
Wow!
There.
Okay, I got it up a little bit.
Maybe just enough to get my big screwdriver under there.
Wow!
Okay.
There it comes.
See?
Jeez!
Okay.
Wow!
You're kidding me.
Why is it so hard?
You know, I'm not sure what's going on with that.
Wow!
Let's see what's happening here.
Man!
See?
Somebody put some mastic or something under there.
And it was all rusted on there.
Get that cleaned off a little bit.
Wow!
That's a buildup of something there.
That shouldn't be on there.
That was keeping that from wedging up on the sides.
See how this is...
See how this cap...
This is the bottom portion of that cap.
And the cap snaps onto that.
And see how it's spinning like that?
It shouldn't be doing that.
And I'm going to have to get a little wrench
and tighten that up.
Before I do that, I want to clean this up a little bit.
Jeez!
Okay.
Wow!
Now let's talk about this for a moment
before you get all rainy and bumptious
and think,
Okay, I'll just tighten that nut down.
It'll be good.
Call it good.
That'll fix it.
I'm going to think about this a little bit.
The interesting thing I first see here
is here's the plastic nut.
On the bottom side...
No, that's a big fat washer.
That's for this cap to snap on.
Okay?
You need to have that down there first
in order for these caps, like this,
to snap on there.
Okay?
But...
You see there's no metal washer
in between this plastic backing piece
and the nut.
Hmm.
They should have put one of those on there,
by golly.
And that's why,
when they initially installed the toilet,
they couldn't tighten this down all the way.
Because this plastic nut,
the plastic washer deal,
see, it can slide.
You see how it slides back and forth?
Because it's got a little notch in it.
And that's designed so that
when you put your metal washer on there,
you can kind of line that up where you want.
And then the metal washer pushes down on the plastic
and the nut goes down on that.
You can get it down tight.
See how this is lifted up?
This plastic?
That's because they tightened this nut.
And the hole in this plastic washer is really big.
And in fact,
part of the nut is almost
pushing through this plastic washer.
And that's why,
see how pooched up it is now?
Look at that.
See that?
It's pooched up like that because
if I tighten that nut any more,
this is just going to pooch up more
and it's not really going to tighten the toilet down.
You see what I mean?
They should have had a washer there first.
And because they didn't,
initially when they installed this toilet,
they could only tighten this down so tight
before it started,
before the washer started going through it.
So they called it good
and then they went ahead and caulked around the toilet.
Well, the other side is exactly the same way.
I pulled it up and we've got that.
So what do you suppose I'm going to do?
What should we do here?
If I put a washer on there right now,
it's really not going to do anything.
Let me tell you why.
Well, there's a couple reasons why.
And the first reason is
I'd have to take this nut all the way off
and then put the washer down in there.
Because you saw how rusty it was
and all that buildup on there.
That was just...
I don't know what exactly that was.
It was just a buildup of stuff
that came up through the plastic
and built up around this cap.
Well, my concern is
if I can't get this nut off very easily,
it might start twisting this bolt.
The bolt that's coming up
has a little groove in it.
And there's a groove in the flange
down in the floor
to where this bolt fits in
so you can't pull it up all the way.
If I start unscrewing this nut,
if I start twisting this,
I run the jeopardy
of pulling this bolt right up out
from the groove in the Herkul flange.
That's the first thing I'm concerned about.
And because I've got another way to fix this,
I don't really want to mess with that.
And it's really not going to do much now anyways
because it's existing now.
It's been down about eight years.
And even if I do put a washer there,
I take this nut off,
it's going to be hard to get off
because the threads are rusty and old
and this might start twisting and everything.
Even if I could get it off,
I might jeopardize and have a problem
with the nut going back on nice and easy.
And once I start tightening that,
it could spin this steel and still come out.
I've had it happen.
And really that's not going to do much anyways
for this toilet because it's eight years old.
And at the floor line, it's been caulked.
So that caulking is eight years old.
There's no way I can push this down to be tighter.
Let me explain a little bit more for you.
Are you learning anything yet?
I sure hope you are.
The toilet was rocking back and forth a little bit.
Just a little bit.
And upon further inspection,
you see the floor is a natural cultured stone floor.
We've got different tiles.
And I notice this back tile is a little bit lower.
This whole row back there is a little bit lower
than the rest of the toilet.
And because it initially didn't have this down tight enough,
when you put weight on there later,
it had a tendency to push back.
Now when they caulked that,
maybe it didn't dry all the way
and somebody had to use the bathroom real quick.
And then the caulking pushed down
and then it got up off the toilet
and then that raised back up a little bit
because this was not perfectly flat on the floor.
They should have put a shim or something
at the front edge of this toilet
after they tried to tighten it down.
But in reality, had they had the washers there,
that could have sucked this down just a little bit further
on their initial install before they caulked that.
Then the caulking gap wouldn't have been as big.
Does that all make sense?
Now, you know, I can't push this down any further in the back.
See, it's raised up.
The front edge is raised up until you sit on the toilet.
Then the front goes back down.
You let go and this springs back up.
It only springs up, you know,
16th of an inch or less, 32nd of an inch.
That's all.
So, what I've got to do is,
no matter how tight I make this,
the front edge is still going to be lifted up
because this, in reality,
the back tile is low and this front tile is low.
And this tile right here is actually higher than everything else
and that's where they tried to tighten everything.
Well, that's where the flange is.
There's nothing out in the front of this toilet to tighten down.
You've got that bolt and one on the other side
and that's what holds the whole toilet.
Because this front tile was a little bit low too,
they should have put a shim down there, right?
Well, they didn't do it and they thought,
oh, we'll just caulk it.
When the caulking is dry, kaboom,
that will suck it all in.
And in theory, that could have worked.
But, like I said,
somebody probably used the toilet
or they didn't put enough caulking in there.
The caulking didn't really stick to the toilet
like they thought it would and all that.
So, I'm going to leave these bolts alone
and I'm not going to worry about a washer or anything.
I don't even think I'm going to tighten that
because I know I've got to raise,
I've got to put something underneath here.
Now, what are we going to do with that?
How are we going to fix that?
Any ideas yet?
You know, I always say
there's more than one way to fix something.
I'm going to explain at least two different ways
you can fix this yourself.