How A Mechanical Clock Works

Chrono Chronicles
8 followers
3 Video Views·Apr 27, 2026
Today, were going to learn the name of the major components, and see how those components interact. Lets look at how the clock turns the power contained in a spring into an accurate system for telling the time. Lets get our hands dirty!
Hello I'm Mark and welcome to the TikTok Workshop. Today
we're going to get back inside this little clock. So to pass the BHI exams
not only do we have to learn all of the parts but we have to learn
all of the parts that make up the parts. So today we're going to take a crack at
learning some of the fundamentals and seeing how the components work
together. But before we do that let's get
everything apart again. So this is the basic layout of the
clock and we're going to break things down step by step.
We start off with the powerhouse of the clock, the mainspring.
When wound a spring stores energy and releases it as
torque, a turning force. This one is knackered it should have way more boing
in it so it's going to end up getting replaced in the future.
The spring is attached to this spindle called an arbor. At this end of the arbor
you can see the threading for winding the key
and on the other end we can see all of the parts that make up the ratchet
mechanism. This allows you to wind up the spring.
That mechanism then drives the great wheel.
When talking about clocks if a gear has more than 20 teeth
it's generally called a wheel and if it has less than that it's called a pinion
and its teeth are then called leaves. There are exceptions however but we'll
deal with them as we come across them in the future.
The great wheel then drives the center pinion which is connected to the center
wheel. The center wheel turns at once per hour
and funnily enough is located in the center of the clock.
The center wheel drives the third wheel pinion
and the third wheel drives the fourth wheel pinion. The fourth wheel
normally rotates once per minute so in many clocks and watches it carries the
second hand. Those previous four wheels make up the
train and they convert the high torque low number of turns that
we have at the spring to a low torque high number of turns.
We're also able to grab the time from the train as long as the speed of
everything can be kept constant. So the main spring has a lot of power
in it and if we were to let it go in one lump it would spin away very quickly.
So speed control is the job of the escapement and the oscillator.
This clock has an escapement made up of this guy with the funky teeth, the escape
wheel, one of the wheels that can have less than
20 teeth but still be considered a wheel
and this fork looking thing the pallets. The escapement has two jobs to let the
train out in small controlled steps and to provide a
little push for the oscillator. This little nudge is caused by the
pallets moving along the slope face of the escape wheel teeth.
That push is transferred through to the oscillator and in this clock
the oscillator is a balance wheel. The main job of the oscillator is to go back
and forth at a constant rate. The balance is made up of this toothless
wheel right here with a spring on one side
designed to expand and contract evenly and a pin on the other. This is where the
wheel receives its little push. So I've slowed things down here so you
can see what's going on. The pin on the balance wheel is engaging
with the slot in the end of the pallet. So when it gets roughly to its halfway
point it's given a push or impulse as it's properly called and this
keeps the balance oscillating. Absolutely hypnotic isn't it? I could
watch one of these for hours. A pendulum clock works in a similar way.
Here I've got the vocal pendulum clock that I made in a previous episode.
We can see that we've got an escape wheel, pallets
and our oscillator the pendulum. Absolutely the same thing going on here.
The escapement is letting everything move in small steps and is giving a
little push to the pendulum which is swinging at a constant rate.
Right we've covered power, torque reduction and speed control.
Let's go back up to the centre wheel and finish things up by showing you how the
time indication works. Okay we've already learned that the
centre wheel is turning once per hour. In this hole in the middle of the centre
wheel lives the centre arbor. The centre arbor
has the minute hand on one end and the little winding knob for adjusting
the time on the other. We need a way of being able to adjust the
time without moving all of the other gears in the clock.
So let's see how this arbor is connected to the centre wheel.
So here we can see how this centre wheel assembly
goes together. So we've got a washer at the bottom,
we've got this spring washer here, we've got the
centre wheel next, another washer and then this bushing here. I'm going to
drive down to push the centre wheel against this spring
and what that will do is it will give us a drive
between the centre wheel and this centre arbor.
But when we need to we can twist this rod at the back, break that
friction connection and that will enable us to be able to
change the time at the front here. You'll see it better when it all starts to go
back together again. But for now I need to drive this
bushing down so I'm going to see if I can find a way of doing that.
So here we go, the only thing I could find to try tap this down with
was this old pen. So I've taken the nib out and hopefully
with a bit of a tap I should be able to seat this bushing.
So the centre arbor passes through the plate and is attached to the cannon
pinion. This pinion doesn't slip and will always
move when the centre arbor moves. Next we have the minute wheel which
neither indicates minutes nor turns at once per minute.
And finally we have the hour wheel, a properly named component which slides
over the centre arbor and carries the hour hand.
So this is how all of this goes together. So we put the
centre wheel, which is this one at the back, back in. That's attached through the
centre arbor to the cannon wheel here.
All of this is turning once per hour. That then turns the minute wheel here
and finally the minute wheel turns the hour wheel.
And we can see how all of that works together.
And as you can see here if I stop that very
rear centre wheel from turning we can still change the time. So there we have
it. That's the basic function of the clock but that is just the tip of the
iceberg. To try and convey the variety of clocks
and watches in one episode is a futile endeavour. So if you fancy
seeing how a person takes themselves from watching a few YouTube videos to
becoming a clock and watch maker, stick around for my next episode where
making a set of hand levers. We're going to reassemble this clock for now
but the next time we open it up we're going to learn a few more names for
things and look at some of the wear and damage
this clock has sustained over its lifetime.
If you want a more detailed explanation of how clocks work head over to the BHI
website where you can find the first lesson of the distance learning course
that I'm taking. Link in the description. Okay thank you
very much for watching. You all know the buttons you need to click to help me out.
Look after yourselves and go and get your hands dirty.
