Antique Seth Thomas Overhaul - Part 8 - Installing Bushings

Chrono Chronicles
8 followers
19 Video Views·Nov 24, 2025
This is part of a complete clock overhaul video, describing in detail the typical steps taken and tools needed to complete a project such as this. This is part of a long series of videos mainly for educational purposes.
Okay, we are back at the table so now
The next part of this project requires a little more
technical
Skill, so we're going to go ahead and just remove that screw
Put that in the cup with the rest of the little parts
Pull these plates back apart again
Which are now clean
What we need to do
Is we need to figure out
Where these gears go and not for the purpose of putting it back together
Those we don't really need
Might need down. I know it sounds like I'm just throwing gears away here, but I'm actually not
What I'm actually trying to do here is figure out which side
These gears went on okay this one
See there again, that's one of those things where you know you take a picture it really helps
Now what I need to do here is figure out which side
Okay, this is the strike one this one's the time one, okay?
So we're just gonna stick that in there without the spring because I want to see
if this meshes
Okay, it does
So this is the gear. I actually really need to take a look at
Now what I'm checking is where the gear goes in the hole
To see how much slop there is
Now this one this one's livable
The front plate would be this hole
checking
Wait a bit of movement, but
Honestly not enough for me to be concerned about it
These old movements were designed to run with play
Now when you're checking for the slop of a gear you're checking to see how far it rocks back and forth in the hole
Okay
You don't want them tight. That's the last thing you want
Now this one's right on the borderline. I would almost replace this one
Or put a new bushing in
but
My attention is on the next hole up right here
That's the one. I'm really really worried about
So what I'm gonna. Do here is I'm just gonna illustrate what I'm what's going on here
And to do this
Now the hole is egg-shaped
Meaning it's wallowed out to one side very badly
What I need to do is put it in the center
Of that oil sink as it's called
Let me just get a little
pointing device here
But it needs to be on this side of the hole not that side
So I need to put a bushing in here, but I'm gonna go ahead and illustrate that here in just a moment
because that is just I
Mean you can see here
How far it moves?
Not so much this way
But the opposite way
So what I need to do is go ahead
We're gonna put a bushing in there
So now what I need to do first is figure out what size bushing I need
Let me make it so you can see something how about that, but anyway these yellow boxes are
My
Set of bushings they're little brass bushings
Various assorted bushings in here
And what I need to do is pick out the right one now like I said, I'm feeling lazy, so you know what?
This was the gear
Let's double check
Okay, so that's
That's where it needs to be
So now I just need to find the right size bushing
So what I'm gonna do here is I'm just gonna pick one
And see if it fits over the harbor
now this one
Is very close
As a matter of fact if I twisted that much more it would probably go right on there
Now that came out of this one if I go one size bigger
Okay, that's too much slop, so I'm gonna go for the smaller one
Yes, they are tiny
So now that I know that that's the bushing I'm gonna use I
Got to figure out what size reamer to use
so now
We're gonna go over here to my magic drawer
This is part of my bushing machine set
I'm gonna transition over to the bushing machine. I'm gonna explain exactly what it is. We need to do so now
We've got our bushing here
Now what I need to do is find the right size reamer
Now I should be an intelligent person and actually mark the holes
But you know I like to do everything the hard way
so
This one here is the right size
So what we're gonna. Do is we're gonna start off
We need that reamer and then I need my centering tool
And then I'm gonna need my bushing pusher
So now what I need to do
Is I always try to work from the back side?
Some people do it the opposite way
I'm not really sure if there's any better way or not
But anyway, I'm just going to
Move these out
Maybe
So now I just need to get this hole lined up, and I need to find the right. It's this one
Okay, good
Clamp that in on that side
Not tight just snug
myself a little bit of
Play there I can
Loosen these up here, and now I can move this around
All right, so now I need my centering tool
So I'm going to put that in here and by the way for any of you that are paying attention
This is a KWM style bushing machine
So
If you're interested in using
this particular style I
Highly recommend actually any of them. There's virgin, and then there's this one. I tend to prefer this one
Because it's American and I'm an American so I'm going to use American made stuff
Like this bushing machine is made in America
Which I was honestly extremely excited to find out
Okay
Now what I did there is I centered it up
to the right portion of the hole
a little bit of
Justin here
Now we're going to tighten everything down
Then we can take the centering bit out
Put that back because I don't need it anymore now for the reamer
twist
Okay, now this
I'm going to try to make it so that you can see what I'm doing here now you see here
We've got it all lined up
So now what I'm going to do is I'm going to start reaming out this this hole
Start it off slow
Kind of take your time go slow because we want to keep it in that centered up hole
That's centered up portion of the hole so in this case. I'm really kind of taking it slow
Mind you this is all by hand
So you can really feel it a little bit bigger here
I know it seems like I'm destroying this movement by making a hole here, but
Don't worry
Everything will be fine now. We're getting to where I can pressure here
Not quite through yet
I'm just having lighting issues here
Okay, there we go
A couple of good turns there as we take it out
now
Just take this guy out
Kind of rough around the edge there I
Think I'm going to throw my chamfering tool in here and just give that a light touch up here
Quick little run around there
That's better
Okay now
Sometimes these are hard to get out
All right, so now we got my pusher
And I don't mean for drugs
So now I need to get the bushing now we want the oil sink portion of the bushing to be facing down or out
Set that in place there
And now is actually where I need
my little hammer
I'm going to bring this down
Give it a little tap to start make sure everything's looking good
and we're just gonna
Drive that puppy home. I just remembered. Oh, no, never mind. I'm gonna beat the tar out of it just
Final okie-dokie, and now we have a bushing in place
Right in the center of my oil sink that makes me very happy
There we go, and there's our new bushing
in all of its glory
Okay, okay, so now we have our freshly pushed hole right over here
Okay, it turned out fairly. Well. It's almost in the center. It's good enough for me
It's a lot better than it was at least now. I know it won't travel
So now what we're gonna. Do is we're gonna go
See if this is gonna. Uh-huh don't fit
Well, okay
No big deal
Remember I mentioned brooches
End up in there and a little bit here you're putting a little bit of pressure, but not a lot
Blow it out a little bit there take our gear
We got it to go through that time
Okay
That's good
Readjust my camera
Do it a little bit more here, so we're still not quite there
We want to get it as straight as we can it's hard to watch the camera and do this at the same time
Okay
That's a good
That's a pretty darn good fit. I'm just gonna give it a tad more though
For good measure because I think I was a little off. Okay there we go
That is a nice good fit no more traveling no more eggshells
No more egg holes
Okay, now we're gonna zoom it back out and guess what's gonna happen next
You know what's gonna happen next
Reassembly that's right
Okay, so now
We're just gonna basically work backwards kind of what I'm gonna
Go ahead and do is put this gear back on now an easy way with these older movements to tell which way is
forwards and backwards is
They have
Now they're not all like this, but this one has ridges see this little
Raised area of the gear where it was stamped
That's always forward on these older movements like older older, okay?
If you ever come across that
Little a little cheating tool there
Remember how we put the tip this off it goes back on the same way
Put it on
Make sure that goes in the hole there we go
Okay, and that's supposed to have a little bit of a snug to it. It's not supposed to spin real free, okay?
All right, so that's back on
Now we got to go and get the bottom over here or the back. Sorry
All of you other horologists out there don't
Okay now oh wait, there's one more thing I have to do I
Need to put the springs back on the arbors
Yes, and there's another step in the process that I need to do
while I'm doing that so
