How to put a clock movement back together - clock repair basics

Chrono Chronicles
8 followers
3 Video Views·Apr 25, 2026
How to put a clock movement back together. In this video Chris demonstrates how he assembles a clock movement in a simple and effective manner
Hey guys, welcome to Chris's Clock Shop. So in this video, I'm going to show you how I put together
a clock movement. There's a couple ways I've done this in the past, but this is the way that I use
and I find that it's very easy to do, the most effective. So I'm going to demonstrate putting
this movement together. All right, so the first thing you're going to want to do is position all
your gears. So this is, I've got two gear trains striking at a time, so it's a little bit simpler
mechanism to put together than if you've got three like a Westminster. So the first step I'm going to
do is I'm actually going to put my elbow on my bench so that my arm doesn't get tired. I put
the plates together, so bear with me while the camera moves. I'm going to put my elbow on the
bench. I'm going to hold my movement flat and what I'm going to do, I'm going to put my plate
up and I'm going to let gravity position it. Now this, so this movement has a spring here,
this wire spring. I want to make sure it gets into the hole. All right, so what I'm going to do is
I'm going to apply a little pressure to get this going in the posts. All right, and then basically
what I want to do is I want to use my tweezers to try and get the barrels in the rear, the bottom
of the plate into position. So I've got this barrel, this barrel, and this wheel in the pivot hole.
Now what I'm going to do, I'm going to take one of my nuts, screw it on just so it's tight and it's
not going to go loose on me. And those pivots that I got in there are going to stay in position.
But I don't want to tighten this down and bend any pivots. So now what I'm going to do,
I'm going to position the center pivot. Then what I'm going to do is I'm going to put this down on
the bench carefully, flat, like so. I've got those bottom gears in position and I can actually lay
this flat now. All right, so now when I've got it laying on the bench, I've got this gear in the pivot
hole, or I'm sorry, this barrel rather, and I got this other barrel on the other side of the movement
in there, and I got that center time wheel in there as well. And now what I'm going to do is I'm going
to hold this like a sandwich. I'm going to apply light pressure to the center of the movement.
I'm going to take my tweezers here. I'm going to start at the gears closest to the bottom
and I'm going to start positioning these in the pivot hole of each. And I'm going to look at which
gears are closest to the plates. They're not all the same width. Okay, so now I've repositioned
my camera on my movement. So hopefully you can see exactly what I'm doing. All right, so I got my
sandwich hand here. I'm applying light pressure with just a hair. Okay, and I'm going to take each
gear and just make sure the pivot is partially in each hole. Okay, that one's already in there.
Okay, my spring is where it needs to be. I'm going to grab the flies kind of in the way here.
You can see this gear here. See how I can grab it. All right, it looks like
I might need the plates to come apart slightly. Come apart just a hair. Okay, I can grab that.
Put it into position. Okay, put my sandwich hand back. All right, now this one I might block your
view a bit. Go down in here. That one. I'm going to grab the fly.
Okay, we got them all. Should be able to just squeeze that together. Okay, so hopefully that
was clear to you guys. So basically what I did was I grabbed each gear and manually put it into
position while I was applying light pressure with my left sandwich hand. I was grabbing the wheel,
positioning it in the pivot partially in the front while it didn't bring it out of the
plate that was sitting in the bottom. Okay, so the plate's got to be close enough to where they can
sit in between both plates without falling out of either one and yet far enough away to where I could
still maneuver them into position. Okay, hopefully that was clear. Hopefully that made sense and was
helpful to you and you're better equipped to put your movements together. I find that for me this
is the easiest way to do it wherein you're less likely to bend any pivots or tire your arm out.
Some people just, you know, hold it up like I did in the beginning and put the whole movement
together that way and that's the way I used to do it but I find my arm gets kind of tired
and I'm more likely to bend pivots doing it that way. So this technique I find is very effective.
You can do Westminster movements, Grandfather Clark movements, pretty much any movement you
can do that with. All right, so let me know if that was helpful and thanks for watching.
