How to Make 45 Degree Cuts With Mitre Box Cut Off Saw...Part 1

VideoJoeShows
86 followers
536 Video Views·Apr 19, 2026
https://www.youtube.com/user/VideoJoeShows
How to make 45 degree cuts with a mitre box cut off saw...Part 1 is what this howto video is about. VideoJoe is getting into his project now. He needs to install some MDF baseboard to some walls in a multi-purpose room & now he is ready to start cutting his baseboards. VideoJoe likes to cut his inside corners, to his base boards, at a 45 degree angle so they fit in the corners nice & tight. Watch & learn as VideoJoeShows you how to use a mitre box cut off saw to cut 45 degree corners for his MDF baseboards...Part 1
https://www.youtube.com/user/VideoJoeShows
that long wall is 189 and 3 quarter inches long and that's from end to end but because I've got
a return on both of those walls the wall ends I've got to cut a 45 on both ends of this and so
I want to long point of the 45 on both sides on both ends okay so the first thing I have to do
is I got to cut a 45 degree angle on here
okay so I don't have much room for air on this long piece I only got a couple inches to play with
and so where to put my mark I'm going to measure this base and it's a half an inch thick just over
a half an inch thick so if I measure over a little more than half an inch and put a mark
okay then I can put my square on here if I want like this and I could shoot for that line on my
45 degree cut you know what I mean that's what I'm going to do because I don't want to take
up too much of this I could have cut it back in here last thing I want is to make this board
way too short okay so that's the line I've got to shoot for now generally when you mark your base
board you can get a mark you know in the center of your base you don't have to put a square on it
all the way across okay you don't have to do that because all you got to do is look at that one line
because we've got the we've got the table set up to be square right so we shoot for that and that's
all the mark we have to do but if you feel more comfortable using your your square you can do
that to mark that because the top has the angles you only have to mark this flat section here you
don't have to try to mark up here and up here and all that the saw will do its work for you
okay slide that out of the way now we've got to get this down
got to loosen that up flop this over at a 45 degree angle tighten this up make sure you tighten
now we're going to cut a 45 now this is going to be kind of tricky
because last thing I want to do is get my hand in there too close you know what I mean
as I slide that up in there I'm going to line that up so that it's square to the table
hold this down there a couple times you have to slide that back
and I'll hold this tight and see where I'm gonna go you know that looks pretty good right there
okay so I've got to keep my hand out of the way as I'm doing this pushing that down tight
there it is see right now I'm gonna have to keep my fingers clean I already got a couple grubbies
on here and I have to watch that but you know I've got my I've got paint on here but I'm probably
gonna end up putting another coat on here doing some touch-up on this base after I get it installed
but I like to I like to pre-paint this if I can if I have a choice
then I don't have to do two coats after it's up against the wall you know what I mean
now I've got to set this on the ground and I've got to measure 189 and three quarters
and that's why I like to tape measure with a lock on it because I can pull that out and
lock it when I get all the way to the other end I'm gonna have to measure to the tip not this
inside cut that I just made but the outside okay don't forget to do that okay so I'll put a mark
down at the other end flip the board around we'll go from there I just pull my tape out and I let
it sit way longer than the board and then I lock it okay now I can come up here and hold it exactly
where I want this point to the very point of the bottom I can eyeball that just look straight down
the tape look at that okay now I can go over to the other end mark 189 and three quarters
the thing I like about MDF baseboard is it's very pliable and flexible look at this
even though it bows like that you can get a piece of base perfectly straight
and uh that's hard to do that with wood baseboard you always get a crown in it or a bow or it's
knots in there or something like that this stuff paints up really nice too that's that's the two
things I like about MDF baseboard paints up really nice and smooth and it's flexible and it stays straight
