How Pros Cut Molding Inside Corners

DirtFarmerJay
310 followers
70 Video Views·Oct 26, 2024
Dirt Farmer J here from Dirt Farmer Jo M
if you're ever installing these a crown
molding or baseboard molding and it's
going into a 90 degree corner and you
want to make it right there's a tip the
pros use stay tuned and I'll show you
what it is
[Music]
alright let's go ahead and begin with
baseboard this is four inch baseboard
but the technique I'm going to show you
works whether it's a shorter profile a
taller profile or a split profile now
one of the ways you can install in an
inside corner baseboard like this is
just a straight miter and as you can see
I've cut a 45 degree on this and I've
cut a 45 degree on this will it work
yeah most the time but it's not the
preferred way to do it if you join these
two together and you put it together and
it's truly a 90 degree corner you're
gonna get a tight joint but here's the
problem
most walls are not 90 degrees that are
either wider or smaller so if it is less
than 90 degrees it's gonna gap at the
back side of the miter if it's wider
then look what's happening it's ugly and
so what you end up doing is filling this
with caulk well there's a method that
carpenters have devised over the
centuries to address this
it's called coping that's really what
it's called COP ing coping and what
we're going to do is actually cut this
section out if you notice the shape when
you cut a 45 degree is exactly the same
shape as the face of the joining molding
so if we cut that all away what that's
going to allow us to do is only have the
joint touch at the front edge and even
if there is some variance this way the
gap will still be tight so let me show
you how we cope them okay the first
thing you're gonna need is a coping saw
you've seen these kind of saws before at
the hardware store and this loop or this
bow around here really allows you to get
in far into a cut but if you look close
at the teeth the teeth are set in a way
I put them so they're going forward like
a standard saw and they will cut on the
push stroke alright let's go to work
here notice that we've cut this piece of
molding at a 45 and when you do so the
front shape of the
jacent piece is revealed right along
here so what we're going to do is we're
going to cut right along this profile
but we're gonna cut back at about a 45
degree angle that's called an undercut
that will allow an adjacent piece of
molding when it's installed on the wall
to just kiss right on the front edge
therefore if the angle is a little wide
a little narrow it's still going to fit
very well this will take a little bit of
practice after a couple cuts you'll get
it and you'll find that your precision
will kick up so first thing we're doing
is we're going to get cutting here
all right we did a partial cut because
that allows us to get another start as
you can see that's pretty doggone close
let's go ahead and get our second part
of the cut going now notice right on
this cut I know of some skilled
tradespeople that actually use their
miter saw and cut this straight portion
and then cut this profile portion to
match it but we're just going to go
ahead and go straight across
all right so notice that this is
undercut a little bit if you look it
from this side you can see the profile
nicely if you look from this side you
can see that I have back cut the molding
that's so that only this front edge is
standing proud so when you went to go
use this let's call that one wall you
would nail that molding on to the wall
this adjacent piece would come up to it
and notice well it's not absolutely
perfect it's certainly within range and
with a little adjustment you can either
back file or sand but notice one of the
big benefits if I pivot slightly in and
out the joint is still tight it doesn't
gap and even just a little bit of caulk
and paint in this corner will be
beautiful well that's how it's done for
baseboard does it also work for a crown
molding absolutely the same theory is
used and let me just show you a sample
of that briefly all right so you'll have
to use your imagination just a little
bit here but imagine that this is the
wall and what I'm standing above the
ceiling and so this is attached to the
wall at an angle like this this next
piece under new jacent walls coming
along notice it's been coped and back
cut but we're gonna roll it and we would
place it up and then bring it into place
and as you can see it's pretty doggone
close and this allows this side to be
nailed all the way into the corner
without both of them
coming out and having a gap behind it
it's a superior way to do it it's
professional and it'll last a long time
hey it'll take you a little bit of
practice and a little bit of noodling
until it becomes muscle memory but
believe me the results are well worth it
if you found this to be helpful once you
like it and better yet subscribe to our
Channel
until the next time this is dura fiber
Jay from Dirt Farmer gay.com
[Music]
