https://www.youtube.com/user/VideoJoeShows How to finish sheetrock mud around an existing Thermostat is what this howto video is about. VideoJoe has just finished skimming out an existing sheetrock wall. He's got all of the wall finished nice & smooth now but there is an existing thermostat in the wall. What should he do about it? He could just paint around it & call it good even though you can kind of see that around the edges it's not finished like the rest of the wall. There's a slight gap between a door casing & the thermostat too. Just an inch or so & it should be smoothed out with some sheetrock mud to match the rest of the wall but oh well. Oh well you say? No. VideoJoe doesn't leave his jobs like this & neither should you. He has decided he should remove the outside clear t-stat cover so he can take a closer look to see how he will go about applying drywall mud nice & tight around the existing thermostat, or maybe he should remove the thermostat away from the wall? Not sure just yet. Spend some time around an existing thermostat when you get ready to skim out an existing wall so it looks like you were never there. What about that little 1 inch gap? Do you have a putty knife that small? What to do what to do. Skimming out around an existing thermostat with sheetrock mud is easy...when you know how. Watch & learn as VideoJoeShows you what he has in mind in order to skim out & finish drywall mud around an existing thermostat on a wall. https://www.youtube.com/user/VideoJoeShows
I'll get back to my patch in a minute but I just wanted to show you something else here.
Here's where the existing thermostat is and because I floated out this entire wall and
I've sanded it and everything I'm getting ready to paint it. See this little area right here?
This still has the old finish and it's got the rough spray texture that I floated over to make
this wall nice and smooth. Well this cover doesn't cover everything exact so right underneath
I can look underneath and I can still see paint on the inside of there. If I take this blue tape
off I can still see it there and up on the top edge and over here. So you know I really didn't
want to but I'm going to go ahead and take this cover off. Luckily I have the key for it. I'm
going to take that off, unscrew the thermostat. There's a backing plate on there. I'm going to
pull all that off the wall so I can finish this area around here. That way when it gets all done
you're not going to see any of those areas because that's just how the project should be done.
You know take your time and little details like this. This is what makes the job
turn out nice and primo. Get in the habit of going the extra mile. I'm looking at this a little bit
closer and I'm thinking the backing plate is separate from this plastic outside piece so
I'm not quite sure if I'm going to have to pull this actual thermostat off the wall or not.
But I definitely want to do something because I'm not finished very well on the edge or the bottom
or the top. There's all these vent holes here and if I there's no way I can get this nice and snug
with the mud because the vent holes are preventing me from doing that. So I don't want to just call
it good right up to there because that's just not the type of statement Joe likes to leave on his
jobs. You know you see there let's make a decision here. I can fill this area up with sheet rock mud
around this all the way along there and I'm going to have to figure out what to do here. My putty
knife won't fit in there but if you get those little thin putty knives at the store like the
one inch you can cut off an edge or a two inch flat putty knife they're less than like a buck.
You can cut off the edge with some tin snips or something and then I can fit that right in there
because I want to make that nice and smooth. So I think that's what I'm going to end up doing
instead of pulling this off. Now I could pull this off if I wanted then I have to remember all the
wires where they go exactly pull this part off and unscrew that and that might be something to do
if they ever want to relocate this thermostat. But see if they ever want to relocate the thermostat
there's going to be screw holes in it there's going to be a nice big chunk taken out of the
sheet rock where they fish the wire down the wall you know and all that. So this area would have to
be patched anyway so I don't think I'm going to take this off any further but I'm just going to
finish that off that way I can paint all that and finish that all off then I can
put the cover plate back on and it will look like it was never there.