FFG's complete wiring harness system for 1967-72 Ford F-Series trucks is here. Jason breaks down everything — how it was designed, what's in the kit, what it works with, and why we spent six figures and hired a full-time electrical engineer to build it from scratch.
Wiring is the number one thing that kills builds. Guys spend months piecing together universal harnesses that weren't designed for their truck, hunting down connectors that don't match, using switches with wrong voltage ratings, and troubleshooting electrical gremlins for weeks because nothing was planned as a system. Wrong gauge wire on a 35-amp fan circuit is how trucks burn down. And when something goes wrong six months later, there's no schematic to trace — just a rats nest behind the dash nobody wants to touch. That's exactly what this system was built to eliminate. If you're doing a Coyote swap (Gen 1 through Gen 4) or Godzilla swap in a 67-72 Ford, this is the first wiring system actually engineered for your truck. Not universal. Not adapted. Purpose-built — the same harness we use in-house on our own builds.
The system starts with the main harness — a modular setup with front, cab, and rear sub-harnesses connected through bulkhead connectors. Everything is pre-wired, labeled circuit by circuit, and designed to install in under two weeks even if you've never touched wiring before. Our guys in the shop do it in five to seven days.
What makes this a true complete system is the five companion kits we built around it. You're not just getting wire — you're getting everything you need to finish the job without sourcing a single part:
You can run just the main harness if you already have your own connectors and tools, but the add-on kits are what make this a wire-your-truck-in-two-weeks experience instead of a two-month scavenger hunt.
Supports Coyote and Godzilla engines, 10R80 and 10R140 automatics, manual transmissions including BMT82 and T-56 Magnum, 6R80, and integrates with Dakota Digital gauges and Coach Control modules. Also set up for returnless fuel systems — pulse width modulated, the way the Coyote was designed to run. We sell the PWM kits that make that work: https://fatfender.com/search?q=Returnless+Pulse+Width+Modulation+Kit
The harness comes with a 60+ page manual that walks you through every step, including what a good crimp looks like versus a bad one. This is the full recipe.
67-72 is available now at fatfender.com. Next up is 53-56 Ford in about 30 days, then 73-79 dentside by mid to late summer. After that we're working back through 61-66 and 57-60, then into Gen 1 Mustangs and Fox Bodies. Chevy LS and LT harnesses are on the roadmap after that.
If you're not doing a modern Ford engine swap — running a 302, 390, 428, or any carbureted setup — this isn't the harness for you. We still sell American Autowire kits for those applications and they'll work great.
Drop a comment if you've got questions about fitment or which kits you need for your build. More questions? [email protected]
Follow along on Instagram @fatfendergarage and TikTok @fatfenderaz for more harness content and install walkthroughs.
We can wire a truck up in like five to seven days. We'll kind of give you a little backstory. So a lot
of the stuff we do is fuel injection, coyote swaps, Godzilla swaps, automatic transmissions,
manual transmissions. We wanted this harness to be able to work with all of them. We take you step
by step on how to do this yourself, but everything is labeled and wired all the way from the bottom.
Our goal is to take what we do here, simplify it down, and make hot rodding for you as easy as we
can so you can enjoy it. And let me show you what we got. Hey guys, Jason with FF Intergarage and I'm
sitting down for this one because there's a lot that we're going to unpack about electrical wiring.
Now we have wired a lot of vehicles and we've had a lot of success. We've had a lot of failures and
it hasn't always gone well. So I've wanted to for a long time try to figure out how to reduce wiring
into a much more simplified process, especially for us at the shop, so that I would have full
schematics and we could take a look at wiring diagrams at any truck that's getting built,
whether it's now or in the future, or we could help somebody track down any wiring issues. Since that
time we've thought about it a lot and we've been really busy at the shop and we've got some good
wiring guys that want to try to do stuff and just time. Time just becomes really, you know, the
biggest problem is how are we going to accomplish this. And so we ended up hiring a bona fide
electrical engineer who's been in the trade for over 30 years. Very smart, he's very well
acquainted with hot rodding because he's a true hot rodder at heart. He's working in his own garage
on the weekends, he's very familiar with LS swaps and you name it. So we brought him on full-time
and for the last six to eight months we've been designing and planning and engineering and testing,
making instructions and wiring diagrams and what would we want in a wiring harness if we were to
design one from scratch. So that's been a very long, painful process but it has come to an end
and let me show you what we got. So we start off building a wiring harness and of course it's all
drawn up in CAD. So everything is drawn in CAD first and we determine, you know, what this is
going to look like and then we come out to a truck and then we start to develop some lengths
and where things are going to go and we start to come up with a little bit of a wiring harness
but made out of string. So it's all out of string and we got a rope that we lay out and that kind of
helps us understand what lengths we want to deal with. And so what we want to do is we'll make it
super simple. We got it in the cab harness with a bulkhead and that's all wired up and then you've
got a front harness and a rear harness. And so this is a cab harness, it doesn't get loomed.
You can take a look here, it's got two bulkheads that go to the firewall and then once that's
attached to the firewall then you have the bulkhead that plugs into it and you take
it to the front and then you got the bulkhead takes it to the rear. So that makes it a little
bit easier that you're not just running a wire. I see it, they'll drill a hole and run a wire.
People won't even put a grommet on the hole, they just can't be bothered with that. And so then that
wire is just sitting there and just, you know, running down the road and it's just, you know,
starting to cut through the outer insulation and then, you know, starting to short stuff out.
That's how fires get started. Or it's the wrong gauge of wire, too small a wire for the amount
of amps or vice versa. And so at the end of the day you get things that just not working correctly,
not the right amount of grounds and not the right plan. So if you have a recipe and you
follow the plan, it works well. And so this is what we were trying to figure out. So we've got
the first wiring harness kit done and we actually have this first already in stock. We'll kind of
give you a little back story. So a lot of the stuff we do is fuel injection, coyote swaps,
Godzilla swaps, automatic transmissions, manual transmissions. We wanted this harness to be able
to work with all of them. So there's a lot that goes into it. We also wanted it to work with
Dakota Digital Gauges. We also wanted it to work with all the modules that they have, electric
motor, wipers, lights, cutouts, you name it, e-stop, everything that we do here and that everybody
seems to want to do as well in their own vehicle. So we wanted to just come out with something that
was kind of like a universal harness. So very simple. Now you'll get these little plates
that allow you to buy, put modules on it if you would like to. You don't have to. You can create
your own and put your modules on it. But we've kind of given you some parameters and made a few
things long enough that you could relocate that. So right out of the gate, you're going to get your
wiring harness. It's going to come like this. It's pre-wired, ready to go. And then you have all the
lengths right here. They're all zip-tied together. It's really easy. All we did was take this,
it's zip-tied. All these right here are all heat shrink. So once you determine the length and you
put your ends on it, then you can slide these down and you can just put a little bit of heat,
they'll shrink on it, they'll stay there. But everything is labeled and wired all the way
from the bottom. Even right here, all these are labeled right here. So you can understand
where everything's going and coming. This is really simple. It took us about 30 minutes to
put this wiring harness up in here. And from there, you're just basically, you know, if you have all
your original switches, you're going to reuse those. Or maybe you bought some new ones from,
you know, Dennis Carpenter, LMC. We actually do sell a lot of different options. So you can buy
all the connector pack, you can buy the crimping tools, all the switches, you can buy the panels.
There's a lot of options that we've made it as simple as we can and also as complex as you want.
You might have your own wire crimping stuff and you might have connectors you like to use,
whether you want to use the, you know, the MetraPak or Deutsch connectors or, you know,
everyone might have a different opinion on that. So we're not forcing you into one way or another,
you can just kind of choose. You also get all the wiring that goes into your door jams,
whether you're going to be doing power windows or not, whether you need, you know, your dome
light working, all the wiring will be there for you to accomplish that. And so that's based off
like a new relic power windows. So all this is kind of wired there for you, ready to go. We've
thought about all the relays you need and all that stuff. And hopefully we've kept it as
straightforward as we can. Now, one might ask, well, you know, I don't know enough about wiring
to do this. That's okay. It's like a 60-page manual. We take you step-by-step on how to do
this yourself and what a good crimp looks like, what a bad crimp looks like. We provide a little
heat shrinking to, you know, go over the, you know, your crimp things so you can kind of heat shrink
that and cover it up. We provide you with everything we need. This is basically a kit we take and we
hand to our guys in the shop and they use it on a build and then wire up a vehicle. The exact same
kit we're using in-house. Now, we might have one or two little things that we change because of
something very specific, but it's rare. This is essentially what we're taking off the shelf
and wiring up vehicles here and it makes it so much easier. So again, a lot of time. I can't
tell you how much money we've got invested into it, but I will tell you it's six figures to get us
where we are and to produce everything. And I don't know how we could have done it if we were
just a wiring shop. And I don't know how we could have done it if we were just a hot rod shop. I
don't know how we would have done this. And the only way we could blend this together is we had
to hire the resources to make it work. So hence, electrical engineer who's a hot rodder and all
the experience from all of our techs at building trucks was what brought this together. End of
story. We couldn't have done it any other way. A lot of work, but we're over the hump and here
we are. So 6772 is available now. You can go to the website and purchase it. It works with Coyote
Motors, Gen 1, Gen 2, Gen 3, Gen 4. It will work with all those. It also will work with the MT82,
Tremec Magnum transmission. It works with manual transmission, 6R80, 10R80. You're good to go.
Now, I believe our guys, we can wire a truck up with this harness front and rear in like five to
seven days. It's done. If I'm a guy who's somewhat mechanically inclined, I've done some wiring.
You'll definitely have your truck completely wired in less than two weeks. If you've never
wired before in your entire life ever, you can still do it. You might have some questions. We'll
help walk you through it. It might take you two to three weeks for sure. So otherwise you're
basically going to a shop and paying them thousands and thousands and thousands and thousands of
dollars to do it. And you hope they did it right. You hope they got the right size wire that they
didn't use like a 16 gauge wire on your electrical fans that need that are pulling 35 amps and
burning your truck. And you hope you got that right when you send it off to them. So, but we've
tested the wiring harness. We know they're good. They're ready to be sold. You can go to the
website and buy it right. 6772 ready now. The next one is going to be 5356. That's going to be ready
in 30 days. And then about 30 days after that, we're going to see a little bit closer to the
middle of summer. End of summer, you're going to see 7379. And then we'll fall back and get 61 to 66
and 57 to 60. We're going to cover all those year making models. We're going to go into Gen 1 Mustangs
and then also Fox Body Mustangs. We'll have harnesses for all those and just kind of encompass
all the Ford stuff that'll be coming next to simplify it. We've got a lot of shops that build
classic Mustangs brand new ones who also would like to purchase this as well and get it in there
and simplify that and speed them up as well. So we're really excited about this product. It is
long overdue for the industry, but our goal is to take what we do here, simplify it down and make
hot rodding for you as easy as we can. So you can enjoy it. And wiring is one thing that will just
frustrate the heck out of you. Now, if you're not doing a coyote motor, we still sell the American
Auto Wire and kits like that you can purchase. This isn't for you. Okay, I just want to make
that clear. If you're doing a regular 302 or 390 or 428 or whatever it is you're doing, right? You
got this nice old school. This is not a harness for you. This is only for those that are doing
coyote swap with all the modules and all the sensors and all the stuff that's going on.
And it's one nicely integrated harness and it makes all this process a little bit easier.
Otherwise, we can sell you an American Auto Wire harness and that will work just perfect for you.
That's all you really need. But at the end of the day, everything is very specific. We're not using
a lot of universal parts. We're using very specific parts that are exactly what have been in your
vehicle. So like for an ignition switch, it's a Ford factory, the ignition switch for 6772,
the exact one. So we're really excited. You can go to the website, a lot coming. Once we get all
this tackled, we'll be moving right over into the Chevrolet side and working on those trucks and
LSs and LTs and all that stuff and making it as easy as we possibly can. Now, I will say this,
we are committed to building trucks the way we feel is the very best. There is a fuel system
debate out there, returnless or return style. We are doing returnless. So we are set up to do a
pulse width modulated system and it's returnless. We believe that's how the Mustang motor was
designed to run. And we believe that's the very best way, the very best fuel pump that you can
use. And we sell a brain that actually makes all that happen. The reason why the Ford instructions
say no to that is only because they don't have the means to control it. But we do. We sell a
does control that and it works great. And we're really happy to use it. And that way your fuel
pumps don't get as hot as they do in using just an air motive pump that's at a hundred percent
duty cycle. So anyways, hopefully I've explained enough and it's crystal clear. You check it all
out, copyrighted it. We've done patents on it, design patents on it to protect us and everything
on it. And so we feel really comfortable now to send it out to you guys and give it a shot
and happy hot riding. Good luck. We'll see you later.