Four trucks are headed to SEMA 2026. We can show you two. The other two stay covered until Vegas, including a '56 F100 where every panel was modified except one. The trucks have to be finished by October 30 before they get hauled to the Las Vegas Convention Center. Our owner Jason walks the whole shop to show where each build stands, because there's SEMA done and then there's done. All four ride on FF Chassis.
PSYCHO 1966 F100 (Closest to finished) - House of Kolor candy brandywine over black - Whipple supercharger - Polished wheels with hidden lug nuts, color-matched bed liner - Interior built and waiting to go in: leather-wrapped fiberglass dash pad, one-piece fiberglass back wall, Mustang seats - The trim isn't SEMA ready yet, so it's getting replaced
1966 Bronco (Furthest behind) - FF Chassis independent setup, Coyote, custom headers - Wilwood brakes, King coilovers, triangulated four-link - Custom billet grille with illuminated inserts, billet emblem, new door handles and mirrors Billet tailgate pieces and aluminum fender flares - Every part gets prototyped in plastic first to check fit, then made in metal and Cerakoted. One plastic mirror did not survive filming.
The two we can't show yet. A '79 F-250 crew cab gets a custom wheel we designed, 3D-printed off-road bumpers, a soft-open tailgate and a working third brake light. Behind the curtain, the '56 F100 has been years in the making, and you get a look at the one-off hidden hood hinge our engineering team designed for it, with the actuator tucked behind the firewall.
Across all four trucks, our engineering team has created 42 new parts. Most of them are headed to the website after SEMA.
The challenge: we unveil the '56 on the first day of SEMA, November 3. After that, the first person to correctly name the one piece of metal we left uncut in the comments gets a free FFG t-shirt.
The interior pieces going into these trucks are the same kind we build for our kits. Good enough for SEMA, good enough for you: fatfender.com/interiors
The chassis under all four trucks: fatfender.com/chassis
Chapters: 0:00 4 Trucks To SEMA 0:25 Build One 1966 F100 3:52 Build Two 1966 Bronco 9:19 Build Two Chassis 12:03 Build 3 (Hidden) 15:14 Build 4 (Hidden) 15:51 Engineering Center 17:33 Road To SEMA
We got 28 days to get four trucks done for SEMA.
And we are not even close.
Two of them, we're gonna show you as much as we can.
And two of them,
I'm not gonna show you anything about those at all.
We're gonna debut those at SEMA.
And one of those is the biggest build we've ever done.
But let's get into truck number one.
So this one is called Psycho.
Well, you've heard of the Bates Motel, right?
Well, ah, ah, right?
All that crazy stuff.
Well, the customer's last name is Bates.
And so he's called it Psycho.
We got some cool stuff.
But 1966 F-100, and this thing is a beauty queen.
Now, one of the things has not turned out well
on this truck, believe it or not, is the trim.
We bought it, we put it on.
And to say it looks like shiz, it looks like shiz.
All right, so there you go.
So we actually got some more stuff coming
that's been straightened and polished
and a little bit better than this.
And we're gonna take this off, replace it.
It's not SEMA ready.
That trim's not worthy to be at SEMA.
But hey, somebody might get a really good deal
on some stuff for an old patina truck.
So come check this out.
So real quick, I'll open this up.
The carpeting's in.
Essentially, this is all done.
We just don't wanna install it because guess what?
When I install this too early, everybody messes it up.
And we got this really cool dash pad.
They're just making sure everything's good.
We're getting ready to wrap this soon.
And we're gonna have a nice leather-wrapped dash pad
on here, which isn't common for 1966.
So we actually have come out
really nice fiberglass dash pads.
So these will be for sale.
And then we've got the door panels, the carpets in.
Check out this back wall.
So this is a one-piece fiberglass
and then a back wall piece.
It holds its shape.
It looks super good.
We're really stoked about it.
And they've got this in.
And then we also will be coming out with those
for the interior kits where you can get fiberglass.
So door panels, kick panels, carpet.
And the seats are super cool.
We've got some really cool Mustang seats we put in here
and done a really nice design.
And an awesome console, which obviously is not here
but it's getting wrapped.
You'll see a speaker box that goes in it.
And very cool.
This truck is a nice house of color, candy paint job.
It's kind of like this brandy wine.
It's got a black undercoat, base coat to start with.
And of course we've got these super killer.
Check these out.
These polished shot wheels
with this little red piece right here.
Turn this off.
You got all the hidden lug nuts behind it.
Super high quality, super nice, super awesome.
And of course you've got a Whipple supercharger under here.
We've got some covers that we got made.
And so we've got a piece that will go right here
and cover all these up.
So it looks really nice.
Battery, our piece that goes right here.
Nice polished front grill, which we're kind of holding off
not putting that on
because we don't want to scratch it as well.
So this will look cool.
One of the things that we put together here
is check this out.
We got a new hood hinge.
So this is kind of the second truck we've used it on.
We've done several before, like 73, 79, 67, 72.
So this is the 61 to 66 and we did it on another truck.
Turned out great.
So then we finalized the kit, got them all made.
And I think they might be for sale on the website.
Pretty cool to check out.
Another thing this customer wanted
was this Pros-Pit cover.
We'll come up with some actuators
and he can open that up electrically
and he can put stuff in here.
We did a color match bed liner.
So it's a nice Brandywine color match bed liner.
And then we've got, he can store stuff in here.
It's a little bit more waterproof.
He can go drive it because he plans to drive it,
go to shows, have a good time.
It's done super well, super high quality.
The chassis, everything is just beautiful.
Really excited about this one.
This is the one that we can show you the most.
The other ones, we're still going together.
Like I said, two of them, we can't show you.
Now this one will be in SEMA
in kind of the main hall right there.
When you first walk in the main entryway,
it's going to be right there.
A really good spot, kind of show this off.
Anyways, off to truck number two,
which is actually a Bronco, follow me.
We are at truck number two.
Here it is right here.
Well, it's not really a truck.
It's more of a Bronco.
All right, close enough.
So we've got this Bronco
that we've been working on for the past year.
And we are going to wrap this up very soon.
This is the one that's the furthest behind.
If you call not having it done by now behind,
maybe we're behind, we're behind.
But pretty cool Bronco, 1966 Bronco.
Let me show you some of the things we got going on with it.
So first off, this color is pretty amazing.
It's kind of this coppery brown.
Now this year, I leaned hard into different colors
that were all the same.
And so three out of the four colors
kind of all come from the same family.
This one, we actually created a grill.
So this is going to go right here.
We've got some cool little lights that go here.
These right here will be illuminated.
You'll be able to check this out.
So kind of a cool concept.
We wanted something more than just the traditional grill.
So we cut it out.
We've got this going in it,
except it's all out of billet aluminum.
Looks pretty awesome.
Another thing we did is kind of designed
our own Bronco billet piece here.
You'll be able to get these eventually,
but you'll be able to get it with or without the FFG logo.
Also, you'll be able to get it with or without
an illuminated section right here.
Pretty cool.
And then we kind of also changed up.
We went to a little square button right here.
And so we've got this with a little bit of texture
right here, a couple of lines here.
We redid the Bronco one.
And actually we did design,
we're coming up with all these internal pieces
that we manufactured here.
So this will go in here.
So this is going to go, there it is.
Check it out.
This will go on here.
This is going to get Cerakoted a different color,
kind of like a silver gold.
It'd be pretty cool.
Another thing we did was we actually did new mirrors.
So rather than just the little, oops.
This side view mirror will not snap.
I forgot it's plastic.
And I forgot that was just for illustration purposes only.
And I broke it.
All right.
So you're going to be able to get these where,
where this will go right here
and your mirror will come right here.
And it kind of is like a mini version of like the truck one,
but a little bit nicer looking.
And I love the look of this on the back.
Check it out.
So these will all be out of billet.
And I think we might make these an actual part one day.
So pretty cool.
We got this cool little rock slider.
Can I, if you notice everything's a plastic,
well, we do it in plastic first to see if it fits.
And if you don't give it to me, I won't break it.
I will break it.
Probably break this.
Anyways, but if you take a look here,
we've actually already got the metal one.
And so they're going to make sure it fits
and then they're going to take it off
and we're going to go put it in Cerakote too.
So pretty cool.
All right.
Got one more thing to show you in the back.
And so this, we actually got, it's going to go here.
Pretty cool.
Nice billet piece.
And we've got side bezel pieces that all line up.
License plate goes here.
You got your light that will be right here.
And then of course you got this piece right here
being made out of billet.
And this would be pretty cool.
Now we moved the Ford here
because the Ford is generally over here,
but then we have a big spare tire right here.
So you can't see it.
So it made sense just to put this right here.
So this would be kind of cool.
So I'm pretty stoked about that.
And then we're trying to decide,
we're playing around with colors.
Check this out.
So we're looking at this color here as the top.
It's kind of got a light texture to it
and it's kind of a matte finish.
So we're just playing around with this.
I need to sit with this a little longer
before I commit to it.
But I think this would look really sharp
and it actually has some nice little sparkle in here
which will look really nice with this color here.
But sometimes you just need to think about it
before you just jump into it and do it.
So a lot of this, when this truck came, pretty rusty.
Didn't look rusty, but like all trucks,
when they come here, having been painted once or twice
and you strip it all down, it's all rusted.
But what we wanted to do is
we also wanted metal fender flares.
We didn't want plastic pieces bolted on.
We wanted it to look nice and look good for a long time.
So this is all manufactured out of aluminum.
We wanted to still keep it like a flare,
still keep it off-road looking,
but also have it tie in
with just a little bit of elegance right here.
Just make sure everything just looked
and blended in real nice.
So the tires actually come out
and they stick out about just about right here.
Super nice.
They're Mickey Thompson tires.
So really excited.
Then we got some really cool wheels we're putting on here.
Some sweet looking six-leg HRE wheels.
So they got some nice round holes.
They're gonna look really kind of classic
and modern at the same time.
So I'm really excited and kind of a bronze color here.
So keeping the theme of bronze.
We did do a bed liner inside,
but we went ahead and did kind of a color match bed liner
instead of black.
And then when we put carpet and everything in here,
if you do see anything,
it kind of looks like it belongs there.
So it also is gonna quiet things down,
help with heat and noise,
and we'll put all the sound deadening material in here.
So we actually just had this on the chassis
a little bit ago.
We'll walk over and show you that,
but we're just making sure everything fits nicely.
Took it off back on here.
They're finishing up some exhaust on it
and we'll go from there.
So the front, everything's the same.
It's got the same kind of fender flares on it.
And then we cleaned up inside here real nicely,
leveled this up.
We've got a little cover that goes there
to hide some wires.
And then our ECU sits right here,
kind of tucked right in here flat.
So it's just not, wasn't sitting on top.
It looks nice and clean.
Little different chassis than what most Broncos are getting.
So let's go check it out.
All right, so we are here with our amazing exhaust team
and we've got Ashlyn and Brighton here.
They are killing it.
And they were putting together some headers,
headers from hell, we'll call it.
Not very easy to make.
It's very tight in this application,
but you can check it out.
A lot of work, a trombone nonetheless.
So we did a little different chassis
and we did an independent chassis here and which was cool.
It's gonna ride really nice, but with a Coyote motor,
man, it's taken up all of our real estate,
literally all of it.
They're trying to get that on.
Once they get that done,
then we're gonna be ready to move it over.
We just need to get it far enough that we can start it.
Headers on it, we need a little bit of length out there
so the O2 sensors will read correctly.
But check this out.
So this is all regular Bronco,
upper, lower control arms with the spindle.
And then of course we got
Wilwood front and rear calipers and rotors on there.
Six lug, we've got our front diff here,
all out of the Bronco that fits
and it kind of just goes, connects right through here.
It's almost straight.
And then we'll shoot down there for there.
So there's a lot going on here.
We wanted to make it comfortable.
He wants to drive it a lot.
And we also wanted to make sure that he had, you know,
something good and reliable.
So he's pretty stoked about it.
Of course, we've got these locked off road
coil overs, front and rear.
Those will help the ride feel really good and comfortable.
And of course we've got this triangulated
link system in the back,
getting all the brake lines on there.
So really close, set the body on here.
Of course, we got a fuel tank we designed for it.
And this goes up into the side filler on the bed.
And of course we've got our fuel lines going right here.
And this is where our pressure sensor would go
for the pulse width modulated.
So now you notice we powder coated this.
This is a really light bronze or dark titanium,
however you want to phrase it.
It's also double powder coated.
So even though we've got this initial coat,
then we actually put a clear coat over it
so that it makes it just nice and smooth, extra protection.
All of our chassis, whether you're going to SEMA or not,
every chassis has that double coated powder coat system.
With all that said,
this will be in the Prismatic Cerakote booth at SEMA.
So that's going to be in the main Hot Rod Alley
section of SEMA, usually in the very back,
kind of by the side bay doors.
And so that will be where you're going to find this.
I think we might maybe have something else in there.
Stay tuned.
That just popped up today.
So, but you're going to see this really cool 1966 Bronco,
fully done, beautiful interior, really excited about it.
That takes care of build number two.
Let's go to build number three next, follow me.
All right, boys and girls,
we are at build number three headed to SEMA
and it's a 19, I almost said what it is.
It's a 19 something and it's a cool truck
and we're really excited about it.
The customer is super cool
and we've done a build for them in the past,
but this one is not like the other one.
This one's super cool.
But let me show you some of the cool things we came up with.
Now, first off, these are the wheels.
Now they're very small.
These are smaller than Goonie wheels even.
They got bigger eventually.
So check this out.
So I had this dream.
I always liked these old school Mickey Thompsons.
I thought they're really cool.
A lot of people buy them, they run them.
And so we actually created a wheel of our own
that we designed.
And so you'll be able to buy these later after SEMA
and after we know how much they actually cost us,
but kind of a hybrid for eight lug or five lug
where you can buy these and get a little bit of both.
And so these are some of the components.
Now, as you can see, they got bigger, but check this out.
So we'll have a little logo cut right in there.
And these would be pretty sweet wheels.
Awesome, they'll be awesome.
A little bit different, but also at the end of the day,
kind of modern, kind of classic.
So we're trying to hybrid both those together.
Of course, we've got, again, I won't break this one.
This is goes on the larger one mounts on.
So perfect if you've got, you know, a truck you're painting
and you wanna weld up, have something clean.
So very simple, clean.
Of course, the same style of mirror size works great.
And then if you're smart enough to know,
we actually did some new door handles.
Now, if you are familiar with trucks,
you know what's sitting behind this screen.
A very, very cool,
but we actually did a little bit different design
so we could actually have this darker shadow in here.
So very cool.
So it'll be two-toned on the truck.
It'll look awesome.
And of course we've got some other little bill of parts,
a soft open tailgate that comes down, third brake light.
We've got icon shocks on this one.
And so you can independently tune active.
So you go to your app and you can control it there.
So, all right, guess what?
We actually found something hiding here
that belongs to one of the builds
that I wanted to show you.
So check this out.
So this is a version of a bumper
that's gonna go on a SEMA build.
That's the front bumper, just in case you wanted to know.
Oh, I can tell you the rear bumper is a lot heavier.
And then we've got this really cool rear bumper.
I love how it's got a little bit of an off-road look,
a little bit tapered here,
kind of hugs the corner a little bit, fits in.
License plate, lights go in here.
It'll be super awesome.
So these are gonna go on a truck
and I think we've actually already made them
out of metal already.
Test fitting them, then we'll finish weld them up,
then we'll metal finish everything.
And then these will actually be Cerakoted
to go on that truck
because we're looking for a certain look
and we're really excited about it.
So these will be a set of bumpers we're creating.
Now we just might, if everything goes well
and it looks good, it's not an actual pain in the neck,
we might make these for good
and put those on the website and you can order them up.
So don't let anybody know I showed you those
because it might be a giveaway.
Pretty cool.
We've got some Toyo tires.
Oh, Toyo tires.
Guess what?
That's where you're gonna see.
This is out in that little overpass,
that tread pass section,
right outside the main central hall there.
You go to the Toyo booth,
you're gonna find this truck sitting there in their booth.
We've got some nice, sweet Toyo tires
that are gonna be on there
and it's gonna be a super awesome truck.
So truck number three
and we got truck number four that's left.
That one, you might just have to wait.
Let's go check that one out.
All right, truck number four.
Well, I don't know if you've ever seen
this 1956 Ford right here.
This twin turbo is awesome.
If you haven't seen, we did a little video on this.
Super awesome.
Intense.
Anyways, truck number four is hiding behind this curtain
and we're not gonna tell you anything about it at all.
It's been in the making for several years.
It's the most wicked truck we have ever built.
It's over the top.
Every piece of metal on this
has been massaged one way or another,
cut, nipped, tucked, modified, you name it.
It's had all the plastic,
well, maybe it's had all the metal fab surgery
that you can possibly do.
Okay, we're in our engineering room
and this is where a lot of the stuff gets made.
So this is a hood hinge on that one truck.
I couldn't tell you what it is.
And this just goes to show you the level of design.
So all this is hidden behind the firewall.
So you really only see this coming out right here.
And so all this is hidden, the actuator, everything's hidden
so we just wanted a super nice clean look.
One of one, the truck's one of one,
but we'll never make this again.
Scott here helped design all this.
We had plenty of versions that we played with,
you know, 3D printing things.
Scott likes to keep all the extra parts
he prints all over his desk.
Yeah.
Yeah, that one's actually out of metal.
Believe it or not, this is 3D printed metal.
So check that out.
What's this, Scott?
I was waiting for someone to ask that.
This looks like a retired, does it bounce anymore?
It's retired bouncing ball.
Retired?
It's retired bouncing ball.
That thing is dry as hell.
This is like a hundred years old.
Throw it on the ground, it'll just disintegrate.
It might just explode.
It still has, I thought it was wood for a while.
It did look like wood.
It does look like, it does look like wood.
All right, very cool.
So this is like what these guys do all the time.
And there's like, I don't know,
how many parts do you think you guys created
for seeing the truck's vehicles?
We're up to 42 parts.
42 parts we've created amongst all the builds.
So it's quite a bit, a lot of design engineering
and a lot of things that have to go together
and also get it done, make sure that it works.
And I think we're close.
Very close.
Yeah, we're very close.
I think we're just waiting for some wheels to show up.
Yeah, wheels will show up
and everything else gets seracoded.
Everything gets seracoded.
All right, very cool.
Thanks, Scott.
Super awesome.
And we actually left one thing we didn't touch.
So hopefully you can let us know
when you see the truck at SEMA,
what's the one thing we did not cut?
There was one thing.
That's it.
Find it, let me know.
And if you can answer that, the first we find out,
we'll give you a free t-shirt.
T-shirt.
Obviously a t-shirt.
Oh, you thought I was gonna say truck, did you?
Free truck?
All right, maybe one of the little ones like that.
All right.
Anyway, so super cool truck.
We're really excited to debut it here at SEMA
and it's going to be in the Meguiar's booth.
So indoor, Central Hall, Hot Rod Alley,
go to the Meguiar's.
There's gonna be two really cool builds there.
It'll be all covered up and we'll do an unveiling of it
and show it all off.
We're really excited about it.
Be there November, I think it's second.
Yeah, I think it's November 2nd.
Anyways, I just know I have to be there
a few days before that.
So please stay tuned.
This is really awesome.
We're really excited about SEMA this year.
We've got four that are going to SEMA.
These are not four easy builds.
These are four over the top, super awesome,
bad to the bone.
It's a lot for our shop considering
we also have a full chassis shop we run.
We have a full interior shop we run.
We've got a bunch of performance parts
and things we're selling.
Like we've got a whole, most two thirds of our business
is something different than building trucks.
So we're super grateful for all the vendors
that are helping us.
And we still got 28 days.
As I stand here and talk, it's not helping anyone.
Actually, I'm not helping anyone anyways.
They actually want me out of the shop.
The shop is so good nowadays.
They actually do such a good job.
They don't need me to babysit them at all anymore.
They just want to know what we're doing
and they get it done.
So 28 days, that's all we got left.
Four builds, two SEMA.
We're super excited about it.
And lessons learned in the past
is do them right the first time.
There's SEMA done and then there's done.
And we try to avoid SEMA done
as much as we can.
We've gone to SEMA and we've had ground wire issues.
We forgot to tighten the negative post on the battery,
trying to drive out.
It's always problematic.
And so it's stressful, stressful for everyone.
I see people pushing, you know, pulling, leaking.
It's stressful.
So we strive really hard to make sure
we get some miles on them
so we can drive them in, drive them out.
And then when we bring them back,
we can hopefully just wrap them up.
So November 2nd, we'll see you there.
We're super excited.
We actually have 13 interiors that we've done at SEMA.
Kits are taking off.
So if you need an interior kit for your truck, hit us up.
They're good enough for SEMA, good enough for you.