In this video I show you how to save thousands of dollars building your own secret bookcase door with the Murphy Door Bookcase Hinge Kit. I spent $150 on the hinge kit and $277 on cabinet grade plywood, wood trim, stain & polyurethane, and a handle.
$2,700 for their archway bookcase. I built ours complete with their hinge kit for $427.
Hi, I'm Mike with House on the Mend, and you are in our basement hallway. Right down from the stairs,
round the corner, coming down this hallway, you see this nice little bookcase decorated
with some books and things. But inside is my daughter Aspen's bedroom. Let's take a look
at this fully customizable door and what I did with the back. Now, typically when you make a
secret door like this, it's going into, say, your gun room or some sort of storage closet. In our
case, it was going to be in the family room area of Aspen's bedroom. So I decided to really decorate
the back of it and make it look just like these barn doors you see over here. And I think it's a
pretty good match. So we are looking at three-quarter inch thick plywood for the back to
make the whole cabinet very stable. And then I used wood trim to make this barn door and a nice
black handle for opening it. I even took the time to take a wood banding and iron on this edge
banding so that I could stain it to the same color. In this video, I'm going to show you how
I utilized Murphy's Doors' available hinge kit and then built my own custom door for so much less
money. Now let's go over everything that comes in the box because when you first unpackage it,
if you're anything like me, it is very daunting to look at all this and go, what am I seeing here?
So let's start with these two. They're the easiest. This is your base plate that's going to
go into your subfloor or, in our case, through our laminate flooring into the concrete of our
basement. This is the hinge on the bottom that is going to attach to the base or the cabinet that
we're actually going to build. Next, we have the upper hinge, which is this and this one.
This one is going to go into your door opening. This one is going to attach to the top
of your cabinet that we are going to build, your bookcase.
Those two are held together by this hinge pin. It has a button that you push in that
reveals or, excuse me, releases these two balls so that you can slide right through both like that
and like that. Now, this will come into play later, but look at how much play you are going to have.
This and this are your friction pin, so this would be attached to your cabinet or your bookcase,
and this attaches to the floor as it comes across here. This guy's on a very hard spring.
That, it comes through and clicks into place holding it. Now, in our case, I didn't end up
using this. I didn't want to put any more drill holes into our concrete, especially when you
consider how small these holes are. I just didn't want to do that. Instead, I used magnets, but
they include that, and it's pretty cool. This guy is your hinge pin removal tool. Also,
it is very helpful for when you're installing the pin. So, inside here, there's a couple notches
that line up really well with this lip right here. So, you come in, you turn it like that.
That pushes the pin and allows you to pull it out. This one here has the slightest amount of, like,
wear or rust on it. It's usually a lot easier than our other one, but if you preload it like this,
as you're coming up, you put the bookcase into place, and with it preloaded, you can get into
what is sometimes a relatively tight spot and push this pin through. Then, once it's in there,
with that friction, you can twist this and it comes off. So, pretty helpful. The last thing we have
is a nice selection of screws. You have some really long screws here that I used for the top
plate to go into the top of my door opening, and then a bunch of other screws if you are putting
stuff into wood that I used for this piece here. The rest of it, I used concrete anchor bolts for,
but there you go. That's the explanation of what each of these strange-looking parts are.
Now, Murphy Door is only too happy to sell you their hardware kit, but as you can see in the
first introduction of their instructions, once you get the kit, they really want to steer you
towards their very expensive bookcase kit. Check this out. We provide hinge templates
based on the doors that we build. If you choose to design and build your own hidden door,
Murphy Door cannot assist you with the customization process. Murphy Door makes
no claim to the ease of designing and building your bookcase. All right, nonetheless, we have
this really well-designed and very sturdy kit, so let's make the best of it with our customization
process. Now, in these instructions, the majority of them is the exact step-by-step of how to assemble
their very expensive boxes, but once you go past that, you get into the process of installing
your hinges. Now, the same kit can do right hinge, left hinge, insing,
outswing. Now, as you saw in our introduction, we are a left hinge and an inswing, so
we are going to be using all of the information for left hinge. Now, you're saying, well, that's
all well and good, but we still need to build our bookcase. So, if you look at this very tiny little
image right here, and we zoom in, you can see these are the dimensions of the kit they want
to sell you. Well, this center section here is going to be helpful because you can see the total
door depth is eight and a quarter inches. I am going to copy that because I'm going to trust
they know what they're doing. If we take that and translate that into the real world, you can see
that we're going to have a three quarter inch face trim. So, therefore, the rest of the bookcase
is going to be seven and a half inches. So, we have that dimension. Now, the door width,
we will get to in the next shot, but the height is going to be based on your door opening,
and I'll go over that with you as well in a moment. So, for our case, let's go over the
hinge placements. Now, the first part of that is going to be installing this base piece. Now,
in our case, we are going to be going into the concrete of our basement floor, and therefore,
I am using, as you see here, our little drill that I recently reviewed that has a hammer drill
function. And this hinge here, from the very front of the threshold, you come in one and fifteen
sixteenths and over a quarter of an inch. So, that is pretty easy to follow. Next, we want to go over
where we place the hinge that attaches to the bookcase itself. So, we go past this page and
we go down to left hinge bookcase template. And you can see, again, they have outswing or inswing.
Again, we're in ensuing. So, ours is going to look something like this, as you see. Now, to make this
easy, I suggest that you write on all your pieces what they are. So, in this case, this is going to
be the bottom base, but it's the front plus the trim, right? So, if we flip it over, now we're looking
at this view. We want to come from the front down four and a quarter inches, but let's leave
three quarter inches for the trim. So, down three and a half inches, and then this side right here
comes in two and nine sixteenths. That's that measurement here, and you can see I have it
sketched out for you. That is how the bottom of our bookcase is going to get its start. Next, let's
head over and I'll show you how we're going to determine the width of our bookcase. Well, this
wall was here when we bought the house, and it's sadly quite out of plumb. So, I'm taking a laser
and I'm shooting a crisscross right on that screw so that I can confirm up there where each of the
dots are going to go. All right, let's determine the total width of our bookcase. So, we've already
installed the hinge over here. We've installed the hinge onto this board here that's going to be
our bottom that we're going to build everything off of. So, we need to determine this dimension
right here, and the way to do that is with it on its pivot over here. You want not only the board
that's going to be the base to clear, but we also have to account for
three quarters of an inch for our face frame. So, I would install your hinge on your board
and then start cutting down this side, back, back, back, until with a piece of trim,
you can open it completely and have say a quarter inch or slightly more of clearance. That will give
you your final dimension. So, the final measurement we need is how tall is our bookcase going to be.
So, that's going to be based off how high your opening is. Now, if you look right over here,
you can see that is the actual piece of masking tape I used to make my calculations. So,
first get your opening, the height of your opening. Then, you need to account for five
eighths of an inch for the upper hinge, then three quarters of an inch for the lower hinge.
Once you have that measurement, in my case, old Justin came a calling, just in case,
makes me do a lot of things that I wish I didn't have to do, but he's a big guy on safety,
so I follow him. I gave Justin a quarter inch. That gave me 80 inches as the actual finished
height of my cabinet. Now, from there, it just came down to my personal preferences.
I used a hinge pin kit so that I could make floating adjustable shelves. I took the three
quarter inch plywood that I used to make the back so it wouldn't rack, and I ran it through
my table saw to make these faux shiplap marks, and I love that. Also, I made the archway to
mimic the one in the opening. I had a permanent shelf right here at 35 inches, which is the same
height as all of our other countertop space, so if I put doors down here later on, it will look
like just a standard height of all the rest of the kitchen cabinetry, kitchenette cabinetry,
all that sort of stuff. That's how I determined what I wanted it to look like. At that point,
I did just standard bookcase cabinetry sort of building process, so I used a dado down here for
this piece here, and then I used a lot of pocket hole joinery that I'll show you in a minute.
When I installed, or excuse me, when I assembled everything, I did it for ease on its side,
and here's what that finished process looked like. All right, well, we have the whole frame glued up,
and I really like to use these homemade 90 degree corners to keep everything square,
so this is just three quarter inch plywood that I've cut into a triangle, and then I cut these
little sections out for the clamps, so as you can see here, this section has been cut out parallel
to the surface that I want to clamp. There you go, and then the plywood doesn't mar the paint
or the finished surface. Now, for instance, the clamps by themselves, you can see here I have to
put paint on the little rubber pads because they'll discolor the paint sometimes, so just a little
trick there, homemade 90 degree blocks. Now, down here is the bottom of the bookcase, and you can see
I've made this void here, and the reason for that is I want to finish the bottom with standard four
inch baseboard that's been used in the rest of the basement, so I didn't want to just attach it
down on this side here and have it just floating, so I made this void, and as you can see right here,
we are over the actual area I made. Well, that's because
the bracket down here and the bracket that's on the floor, they equal three-quarter inch
standoff from the ground, and this is actually a five-eighths of an inch standoff,
so it should be one-eighth inch from the actual floor, and if it ever has an issue and it's
starting to rub, I can just shave off a bit of the faux baseboard. Now, coming around to the back,
you can see, man, that just looks so nice. That's going to be a pretty decent match for her barn
doors, a little darker, but I really like this color. So, along the area where we're going to
have the z trim, the same kind of trim as on the barn doors there, I have actually used screws
all the way along here and countersunk them in with a countersinking bit, and that way
we're going to get really good strength on this three-quarter inch back. The rest of the field
is all glue and nails, so before we put the trim on the front or on the back here, I think it's time,
and Maverick agrees, to do a dry fit. All right, once you set the bottom hinge into its pivot point,
then you come up here, and with this pin, you press this button to release the little ball on top,
slide it through both holes like that, then these little balls come out so that it can't
slip down, and at that moment, this one is engaged as well, and you get nice smooth tracking.
Now, on the opposite side of the door, this is the bookcase side, of course, we can now start
laying out how we want the trim to be. Now, we have about a seven-eighths inch gap right here,
about an inch and a quarter over here, but remember, we don't want to be cheating over
this trim because we run the risk of it rubbing, and we definitely don't want that, so to be safe,
again, I'm just going to have the trim come just like this, right on the edge of our box.
That'll give us a nice, what, three-quarter inch or so overhang here, and then we can take our
four-inch casing, and when we set that up, going halfway across this piece of trim,
just like that, we'll be able to cover up the drywall screws right there, nail into the two-by-four
stud, and also a nail into this solid wood bit of trim here. If we come over to this side,
and we set up for that exact same reveal on the inside, the exact same overhang of halfway across,
once again, we'll be able to cover up the drywall screws and get adequate amounts of nails in,
so that will work out perfect. So the next thing I'm going to do is just confirm all the measurements
of the actual box and start building that face frame. So the best thing is to put the two vertical
pieces in, and lastly, measure for the top, 40 and 7 sixteenths, and just like that, the face frame is
done. On this top piece, I made it a little thicker than the sides, and I put this nice
little decorative arch in there, gives it a nice little extra touch of detail. Then I went around
with this just four-inch kind of casing material, and I framed out the doorway to make it look quite
finished. I went around, filled in all the nail holes you see here with filler, so both of these
faces here are filled. That filler is dry so we can sand and paint. Now, right before we do that,
though, I have been working today on these shelves. So you can see here I have cut back
the face of the shelf a little bit to make up for the face frame. So that is going to come right in
here. We'll put the little pegs in to hold on our adjustable shelving, and I made three of those,
so I think that'll look really nice to be a convincing bookcase. But I think the next thing
to do would be remove this, sand everything down, paint all this face frame. Then once that dries,
we can flip over our bookcase and start working on the back kind of Z barn door pattern.
Now I'm just marking out for our little Z crossbars here. Looks like in our case
we are 41 degrees. Hi! What are you doing? That's a good boy. Here's the handle I got.
Looks very similar to the barn doors in her room as well, and that's going to fit nice
right there. All right, I love that look. I think it's time to break this all down,
sand everything. We want to ease these edges because they're pretty sharp.
Then stain in the same color and put a couple coats of polyurethane.
Well, through the magic of YouTube editing, here we are with every single piece stained and two
coats of polyurethane. It is a really nice match, and I can't wait to see that handle right over
here. So I've got my favorite WORX switch driver here. You easily switch from the bit to the drill,
pre-drill, switch over. In this case, we are using some really nice black screws that are
going to go well with these cuts that we have in it that are nice and dark and that black handle.
So this is the Venon Pro replacement battery that I'm so excited about because for the first time,
my WORX switch driver has a battery life indicator. It's also three times the battery
density of the little battery that comes with it. If you're interested at all in that video,
it's right up here where I reviewed these replacement batteries.
So first thing I want to do, I have these all lined up. Let's start by gluing this one,
clamping it in place, and we'll just go right on through. Enjoy this nice montage.
Nice. Now a couple last little bits. First, if you can see right up here is the magnet that I
installed. I used a kit that I'll leave a link to. I found it at Home Depot, but it has a hole
through the magnet so you can screw right into the magnet and hold it in place. I also took a
Forstner bit and I drilled into the wood so that I could set it flush with the bookcase. And as you
can see here, listen, it holds it really nice and tight. Also, you may notice, I'm not sure if the
camera picks up, but I still need to paint and caulk all this trim around it, but I wanted to
give you an idea of the kind of detail that I used to make it look like just a built-in bookcase
and add to that kind of secret entrance feel. So do you have any questions for me? Anything I didn't
go into? I edited a lot out of this video to make it very digestible, but I'm very approachable.
You can leave me a comment. There's also my email in the description below. Also in the description
below is going to be a link to the bookcase hinge kit. Also links to all the tools and things that I
use that I think would be relevant. Now, full disclosure, those will all be Amazon affiliate
links. So if you click on them and end up making any purchase whatsoever, it doesn't cost you
anything, but I do get an extra reward for driving you to Amazon's website. That's super helpful to
the channel to help pay for all the costs and things that are associated with making a video
like this. If you found it helpful, also will you please give me a thumbs up and also please consider
subscribing. Both those things are super helpful to the channel. This is one of the last sorts of
things I'm going to be doing for our basement build, but I will have a couple other little
cabinetry things for storage and organization going on down here. One of them is going to be
kind of a fold-down tabletop area enclosed in a cabinet so that I can fix guitars and guns and
do overhead camera shots and things like that. I think that build would be pretty interesting
for you and that'll be at a later date. I also do lots of tool reviews that I think
you'll find very helpful. So until next time, thank you for watching.