The Art of Arrow Making - Split Timber (Chapter 2)

Unraveling the Ancient Longbow
4 followers
10 Video Views·Feb 15, 2026
Chapter 2 of the Art of Arrow Making Series covers the split-timber method, which is an excellent way to make high-quality wooden arrows from common boards (or logs).
The "shooting board" jig was in widespread use throughout the Medieval Times; but there's no telling when it was invented or just how old it really is.
This is my personal favorite way to craft arrows, because it gives you a tremendous amount of control over the process and can produce closely matched sets faster and with less effort than other methods.
This set receive feather fletchings in Chapter 5, which will cover four different methods of fletching arrows; and points in Chapter 6, which will cover four different styles of arrow points.
Welcome back everyone to the Organic Archery YouTube channel.
Today's video is chapter two in the six-part
Art of Arrow Making series, and today I'm going to teach you
how to make finely matched wooden arrows using split timber and a very old jig
known as a shooting board. Now I'm not going to pretend I know exactly when the
shooting board was invented, but we do know it was in widespread use
Planing arrows by hand on a shooting board is my personal favorite method
because you have a tremendous amount of control over the process,
and you can create very closely matched sets
because you are extracting them from the same board
stacked up right next to one another. With all the other methods in this
series, there's a lot more variability in the
materials. We talked about how with dowels you can't even be certain that
all the dowels are coming from the same tree
or the same location, and with wild materials like
river cane or bamboo or plum or hazel, dogwood, etc., you can get
some finely matched sets, but it's a lot more work
than if they are nested together in the same board.
One of the ways split timber arrows were made historically was to
cut down a tree and then buck the log to say
36 or 40 inches or whatever length you felt you needed to account for any
checks that might happen during the drying process,
and then you would split it out into bolts, which
are pie-shaped wedges that look a lot like a bow stave
or like a bow billet, and from there you would take a fro
or some other long blade and split those down
into arrow blanks. The benefit of splitting your blanks out of a log with
hand tools is that they'll follow the grain
perfectly and you end up with arrows that have no runout,
but the biggest con is the drying process,
because like bow staves you would have to air dry bolts for
one or two or maybe even more years depending on your environment.
With a kiln dried board, so long as you have carefully selected the grain,
you can process your arrow blanks immediately with power tools and turn
them into arrows right away. Now, is splitting your blanks with
power tools traditional in a purist sense?
Definitely not, but remember I'm trying to teach you guys how to build arrows
fast and good, and when you do this for a
living there is value in doing things in a
timely manner. I make a lot of bows and arrows, so
it's been a journey for me over the years to try to figure out how
I can keep the traditional ways alive, like
planing and fine-tuning each one of these arrows by hand,
versus making my life a little easier with power tools.
I don't personally feel the need to hand split each one of these square
blanks, you know, in early parts of the process
when I have a table saw that can do it much quicker.
You're gonna have to find out where that line is for you personally,
but I have no shame in using power tools for the monotonous stuff,
and then switching to hand tools when the project requires care
and finesse. Let's get into selecting the materials for split timber
arrows. Okay, we'll start with this hastily drawn
diagram to show you guys what you're looking for
when you get to the hardware store. So flat, rift, and quarter sawn boards
will all make perfectly good arrows, so long as you're particular about the
grain selection. So on the left side of the page here, I
have drawn ideal examples of all three, and then
we've got some so-sos in the middle, and some boards
you would avoid for arrow making on the right.
So you can see with flat sawn, so long as that grain runs true
all the way down the center of the board, you're good to go.
Here's an example of a flat sawn board with
long runouts. So maybe over the length of an entire arrow, there would only be one
or two runouts. This is a board that will make serviceable arrows,
although they won't be quite as durable as one with perfect grain,
but this is one that you would take home. This is a flat sawn board
with extreme grain runout, and I would avoid this
at all costs. Moving on to rift sawn, you can see same as with quarter sawn,
the grain kind of runs down the length of the board.
Here's a perfect example for arrows where you would get maximum yield from
this board, because you could just rip it from left to right,
and all of these would be perfect. This is a rift sawn board with so-so grain.
You can see that over a long distance it's kind of
running at a slant. You would be able to get
arrows from say the center section here, because you could plan it out,
you know, to make that grain run straight down the arrows, but you would
have waste on this side and waste on this side.
So there'd be some good arrows in here, but you wouldn't maximize your yield
from this board. And here's a rift sawn with terrible
grain runout. Avoid at all costs. For quarter sawn,
that's basically with the grain running straight up and down.
Here's a perfect board, maximum yield. Again,
here's one where the quarter sawn grain is kind of running at an
angle, so that maybe you get yield from the
middle of the board, but have a little waste on the side.
But again, perfectly serviceable arrows, so long as you're okay
with missing out on some of the wood. And then over here is a quarter sawn board
with extreme grain runout that you would avoid.
Let's head to the hardware store and look at some real boards.
Many different wood species can be used to make arrows, and they all have their
pros and cons. Today we'll be looking at poplar,
aspen, and pine, but pretty much anything you have
readily available in your area is worth a try,
so long as the grain runs perfectly straight down
the length of the arrow. And of course, at the end of the day,
the best arrow wood is the one you have access to.
Just like in the dowels chapter, the most important part of the process
is the grain orientation, and you have to be willing to walk away from the store
empty-handed. These two poplar boards might look
tempting, but they have too much runout for safe,
durable arrows. This is a great piece of poplar,
and it's six feet long, so you could cut it in half and get two
pieces of arrow wood. And so long as you didn't mind
a little waste on the far left side, you'd get some excellent arrows from it.
Here's a piece of flat sawn aspen with really nice grain,
and it's only got one runout over its entire length.
Don't forget to check out some of the less common cuts in the store,
because these two poplar squares have nearly perfect grain.
And be sure to avoid anything that's laminated. If it's glued together,
it's not suitable for arrows. It doesn't matter if the board is flat,
rift, or quarter sawn, so long as the grain runs straight.
So the flat sawn piece in these shots is good for arrows,
and the rift sawn piece is not quite good enough.
When I try to imagine the arrow blanks cut from these two pieces of pine,
there would be several runouts along their length, so I'm gonna pass.
I know these examples are moving fast, so hopefully you're picking up on the
pattern, but the one on the left in this shot is
almost perfect, and the one on the right is a no-go.
Today I brought home a piece of flat sawn aspen
and flat sawn pine with nice straight grain and minimal runouts.
Okay, so before I get all geared up and make a huge mess, I need to talk about a
couple more things, and hang with me because it's important
information. But the first is another major pro of the
method, and that is the ability to create arrows
from warbill arrows down to 516s kids arrows,
and everything in between. You know, so long as your shooting board can
accommodate, you can make the arrows any diameter or
length you want. The second thing is, I started right after I got out of the
Marine Corps in an apartment complex, and I had no way to store or run a
table saw without driving everyone crazy. So I would go to lumber yards or lumber
specialty stores and purchase the boards and ask them to
rip it down into 3-8 square blanks for me,
and you're gonna have to pay for that service. It's usually a small fee, but
sometimes they charge per cut, and so it can add up.
But if that's your only option, you make do with what you've got.
From there, I got my own place and one of those really small
job site table saws. I think it was like under 200 bucks for sure,
and that worked well. I made several hundred arrows with that thing, but I was
always sketched out by it because they're very loud and a little bit
untrustworthy. They just aren't made to high standard.
It wasn't until just a few years ago that I found myself in an estate sale
where they had this big cast iron table saw that had been completely unused
for 500 bucks. But just know, you have options.
You know, you don't have to go out and spring for the big
pro-grade table saw. I've also cut many arrow blanks
on my small bandsaw, which has the benefit of a smaller
kerf and therefore less waste. But just get creative, guys. Part of
making your own archery gear is solving problems.
The third thing is table saw safety, and I am not a stickler for safety
by any means, but I want to remind you to
watch table saw safety videos if you are unfamiliar with the tool.
They're very powerful machines and they command respect.
And when you're ripping arrow blanks, the dimensions are very small so you
know you're close to the blade and there are things that could go wrong.
So I'm not going to act like I'm some master
safety instructor on the table saw, but I am
very careful and very alert when I'm ripping arrow blanks.
The final thing is some starting dimensions for you, depending on what
diameter of arrow shaft you're going for. So I like to use millimeters, mostly just
because the way this saw is set up, it's easier to
read the millimeter marks here. But when you're first learning, I would
encourage you to make the arrow blanks like one
millimeter wider than you think you're going to need,
because there is a little bit of a learning curve with the shooting board.
And we'll get into that shortly, but if you're getting a bunch of tear out over
there and you're struggling to figure it out,
you don't want a whole stack of blanks that are ripped
really close to finished dimensions. If you leave that one millimeter of extra
material on there, at least when you're, you know, first
figuring it out, you're going to have some room to adjust
for any problems you run into on the shooting board.
Every wood is different, so we can't possibly get into the weeds and talk
about every wood species and every diameter and every spine.
You're just going to have to experiment. What might be wise,
if you're working a new wood for the first time, is maybe rip yourself an
8, a 9, and a 10 millimeter blank and turn those on the shooting board
and figure out which one, you know, weighs
and spines the best according to your intended use.
Unfortunately, there's no way I could possibly tell you
what diameter or wood species is going to fly best
out of your specific bow, so you're just going to have to figure it out.
And that's part of the fun. I make my arrow blanks 36 inches long
because that's the length of my shooting board,
and my finished arrows are typically around 31 inches
from the valley of the nock to the back of the point. But you can make your
arrows as long as you want, so long as your shooting board can
accommodate the extra length. And I'm starting with the Aspen board
here, which I know from experience is slightly
lighter and more flexible than some of the other wood species,
so I'm going to start with 10 millimeter blanks for this one.
Most of my bows are between 60 and 70 pounds draw,
so the finished arrow diameter of slightly larger than 3 8s will ensure
that these are plenty stiff. But if you're shooting a lighter or
heavier bow than that, you just adjust the width of the blank
up or down as needed. And I moved right into the Pine board
here, which tends to be slightly stiffer than
Aspen, so I'm going to go with nine millimeter
blanks for this one, which will give me a finished arrow
diameter around 23 64ths. Most of your starting dimensions will
come from experience and trial and error, but if you
leave that one millimeter of extra material,
you'll have plenty of room to fine-tune later.
Here they are ripped into 9 and 10 millimeter arrow blanks,
and I got 10 from the Aspen board and 11 from the Pine board,
so 21 blanks for less than $20. And there was very little waste.
All right, now that we have our square arrow blanks, we need to make them round.
And that's where the real MVP of the process comes in, and the whole point of
this video, and that is the shooting board. And I'll
show you guys a close-up of the construction and talk about that
shortly, but basically it's used alongside a hand
plane to accomplish three things. Make the
square blanks round, make them uniform in diameter,
and taper them on the ends if you wish. The tapering feature
is more of a bonus and not really a necessity, but in some cases tapering the
ends of the arrows can improve your arrow flight,
or in specific historical replicas like arrows from medieval England, for
example, the arrows would have been tapered from
about a half an inch in the front to three-eighths in the back. Okay, onto
the shooting board. It's a very simple jig. This is two
pieces of one by three poplar, and you don't
have to use poplar. You can use pine or oak or anything
you've got access to, but you can either glue
them or screw them together. I've got these
glued and screwed, but right before you glue them together
you're going to want to make a v-groove, and that's done using the
same hand plane that we're going to use to make the arrows,
but I just make a little mark a quarter of an inch down
and a quarter of an inch in, and then I run that line all the way down the
length of the board, and I cut it off flat with a plane, and
then when you glue them together you end up with a nice v-groove that
runs all the way down the length of the
shooting board. Taking off these outer edges here, that's
not really necessary, but I found that when
you're really getting into it and you're
working the arrows quickly and, you know, trying to get a batch done,
if your plane slips at all it's going to contact those edges anyway,
so I just chamfered those so that that's a non-issue.
This one is 36 inches long, but feel free to make your shooting board as long as
you want if you want some really long arrows.
Lastly, there's an end cap right here, and it's just
flush with the rest of the jig, but you can see
it creates a little backstop right there so the blank can't slide out the end,
and I've just got that glued and screwed as well,
and then there are also a couple tick marks
every six inches, and those are just little marks for me
to use when making tapered arrow shafts. So the square blanks fit nicely into the
groove. Backstop keeps them from sliding out,
and you plane the top edge here, first taking
the four-sided blank down to eight sides, then from eight down to 16, and then just
like in the dowel making video, we chuck them up in a drill
and spin them real fast to make them perfectly round.
The next thing you're going to want is something to size the arrows
so they're nice and uniform, and I like to use this drill bit sizing guide.
They're only a couple bucks, it's nice and compact,
and this one goes from a sixteenth of an inch
all the way up to a half in one sixty-fourth inch increments.
So I've got all the common arrow shaft sizes already
right here close to one another. 5-16ths, 21-64ths,
11-32nds, 23-64ths, 3-8ths, on and on, all the way up to a half.
So this one's really handy. You don't necessarily need a sizing guide like
this, you could just take a piece of scrap metal or scrap wood
and use the drill bit that's the same diameter
as your desired arrows and drill a couple sizing holes in a piece of scrap,
and that works just fine. You're also going to want
a hand plane or a thumb plane and the means and the skills to make
these razor sharp. My two favorites are this
vintage Stanley 102 and this vintage Stanley
thumb plane. Both of these are very common
and they're super easy to find online for just a few bucks.
I probably, I don't know, paid 10 bucks for this one and 20 bucks for this one.
The only thing is when you buy vintage, you will have to spend some time
on the blade. A lot of times they have a little bit of pitting
or maybe some improper sharpening, so I spend quite a bit of time
flattening out the base of my planes and then putting a really nice
edge on them. So regardless of which brand or
style of plane you choose, you're going to want to
get that thing hair popping sharp to the best of your abilities and it
doesn't really matter how you get there. You guys know I'm an
advocate for the freehand sharpening method.
The one place I don't freehand sharpen is anything that requires a perfectly
flat and square edge like a plane or a chisel and I've
tried to freehand sharpen these over the years but I always get dished edges.
So I eventually moved on to those little jigs where you put them in place and
they've got a wheel on the back and you just roll it back and forth
on the whetstone or the diamond hone and those work fine
but over time my edge would fall out of square and I'd have to spend a
bunch of time truing it up. So that brings me to today's video
sponsor, Advanced Machinery. And Advanced Machinery was kind enough to
send me over one of the Tormek T8 whetstone sharpening systems
and this thing is the Cadillac of sharpeners.
The Tormek obviously falls into the category of luxury tools
and I've been eyeballing one of these for years. I just never got around to
buying one but I like to use what they call edge
matching in the manual which helps me get the same grind
every time and quickly. The stone runs through a water reservoir so you can do
everything from establishing a grind to edge touch-ups
without ever worrying about overheating your tools.
I'm just running the standard jig that comes with the unit and I think my
favorite thing about this machine is how quiet it is.
Loud machines drive me nuts. The stropping wheel and honing compound
put a mirror edge on your blades. Look at that. Perfectly ground and
nasty sharp. Now that I've got my plane razor sharp
I'm going to put the first of the aspen arrow blanks in the shooting board
and plane it from four sides to eight sides
to 16 sides. One thing you want to keep an eye out for
are grain tear-outs. You'll usually get two sides of the arrow to plane
perfectly smooth from one direction and then you've got to flip it over and
plane it from the opposite direction to prevent tear-outs.
If you continue in the direction that is getting tear-outs they're going
to go deep enough that you'll have those in the finished arrow
and that creates a weak spot. So I got my first two sides here
no problems at all nice and smooth and then on this side I started to get some
tear-outs. So I just flip it over and carry on with
the last two sides. Now I have an eight-sided dowel. I'm going
to go ahead and turn that into a 16-sided dowel. Now it's 16-sided
and it's starting to look a lot more round. This one is ready for sizing.
Typically I'm just going to take the whole stack and I'm going to rough them
out into 16-sided blanks and I'll start sizing the
whole stack but for the sake of demonstration I'll run
this one through. I'm just going to find on my drill bit
sizing guide here which one of these holes
the arrow slides nicely through and obviously if you have an area that gets
stuck you might be a little inconsistent in
your diameter so you would just take a little wood off that area.
But this arrow is fitting nicely through 13 30 seconds
which is just perfect. That's two sizes on this guide
too large or a 30 second of an inch too large.
I want these aspen arrows to finish out at three-eighths diameter
so with this being two sizes too big by the time I sand out all the tool marks
and make this perfectly round with the drill
it should slide nicely through the three-eighths
sizing guide.
Okay so I roughed out six out of the ten that I had because I
almost forgot I need to save a few of those
to make the thumbnail for this video when it's all said and done.
So here are six 16-sided arrow shaft blanks. They're still
pretty rough looking from the planing process
and they're also very angular so we need to make these
nice and round and smooth and if you don't have access to power tools or the
means to acquire them the manual way to accomplish this would
be to use either a card scraper or a pocket knife and scrape them down
until they're more round and closer to your desired
finish diameter. The fastest way to do it would be to use
a belt sander but you also greatly increase your risk
of taking off too much material and having these come in
under spined if you use a belt sander. My preferred method is kind of the
middle ground. It gives you good speed and control and
that's to chuck these up into a high speed drill and spin them
in some sandpaper and from there I'll use the sizing guide to fine tune
them and make sure the diameter is uniform down the
entire length. Just like in the dowel chapter I'm doing
a little preliminary straightening so they don't have too much whip when I
spin them in the drill and then I run them through some 50
grit sandpaper and try to take an even amount of wood
off the entire arrow. Okay I've got these nice and smooth and
round and free of tear outs and I've already
got this one sized. So with my goal
being 3 8's I'm going to size the arrows
on the drill until they fit through one guide hole larger than my
desired finish diameter. So as long as I can get
the arrow to slide effortlessly through the 25
64th hole with no snags nice and smooth
I know that by the time I take all the spiral marks out and sand it with a
finer grit it'll slide right through the 3 8's hole and it'll
be the perfect diameter that I was aiming
for. So I'm going to go ahead and spend some
time on the other five getting them sized because you can see
they start to fit through then they get hung up
so you take even amounts of wood removal off the entire arrow until the whole
thing fits through the guide. You wouldn't want to do little spot
treatments because it's very difficult to get a
uniform diameter when you do that. So I'll continue to
take even amounts of wood removal off until the whole thing goes through for
the whole set. All right so now that the entire set is just slightly oversized
I'm going to run up and down the length of the arrow with my 50 grit sandpaper
to get rid of all the deep spiral scratches from
the sandpaper and the drill and from there
I'm going to cut the waste off the ends because you can see one side gets
crushed by the drill and the other has a little bit of a
So I'll take about an inch off either end make them
all the same length and that's my chance to weigh them
to see if I need to take off any more material
to get a weight match set. All right let's see what we get
I might have to tear this a bunch of times because it's really cold in here
and this scale is pretty finicky when it's cold
so you might see the numbers jumping around but we'll try to get an accurate
reading. 466, 460,
462,
462, looking good so far, 464,
462, all right doesn't get much better than that.
This just goes to prove one of the pros of this method that I spoke about in the
beginning of the video. I didn't even have to do any extra
sanding to these I just sized them to 3 8ths cut them all
to the same length and I've already got a half a dozen
arrows that are weight matched to within six grains of one another and
that's not always going to happen especially when you're first learning to
size the arrows but there's a better chance of that
happening with this method than any of the others in this series
because the arrows are nested together in the same board
but if you're trying to make a closely matched
set for extreme accuracy I wouldn't settle for any more than
about 20 grains variance and I would probably try to get them
closer to within 10 grains of each other
but in realistic hunting scenarios you can have quite a bit of weight
variance and still shoot accurately out to say
15-20 yards but by matching them a little bit more
closely you're pretty much just trying to
eliminate one of the variables. All that's left to do to these is step
down the sandpaper so I'm going to go down to 120 and then
220 to get a nice smooth arrow and then I'm going to carve the nocks and
they'll be ready for seal air. I'm using the exact same method I used
on the dowels to carve these nocks so if you want a detailed step-by-step
tutorial go back and watch chapter one.
Always remember the most important thing about the nocks is cutting them
perpendicular to the grain. I'm using the same set of tools I did
in chapter one where you will also find a detailed tool breakdown.
And again the second most important thing is that the nocks are cut
perfectly straight. I'll finish this one in silence.
The final step for these arrows to prepare them for fletching
is to seal them to protect them from moisture
so I'm going to use tongue oil and I will apply it
in the same way I did in chapter one with the dowels
so one coat a day for three days. But before I sign off on this video I
want to talk about spine and making tapered arrows. I know spine
is going to come up in the comments and I
used to be really particular about it. I would weight match my arrows and then
spine match them to within five pounds of each other
but over the years I just found that for me personally
spine does not matter quite as much as weight matching within reason of
course. If you have an arrow that's say 30
pounds over spine or something crazy it's definitely going to struggle to
flex around the bow. It'll make excessive noise and fly
crazy. Or if you have arrows that are way too
weak in spine they might flex enough to break out
right. But with a little bit of experience
you'll be able to tell that they're in the ballpark.
If you flex these arrows and they feel like noodles it's probably safe
to say they're not safe for a hunting weight
bow. Or if you're putting a bunch of pressure
into them and you can barely get them to flex at all
they might be too heavy. By leaving them extra long
from the get-go, in this case these are 34 inches
before points, that's going to give me all the room
I need to tune them. As you shorten the arrows they become stiffer in
spine and vice versa. So I'll be able to match
these to one of my bows no problem at all. I already know
they're perfectly weight matched and if I need to tune them it's done
after the fact by trimming the arrows down.
There's no doubt that if you want to be as accurate as possible
and really optimize your gear to the highest level
you need weight and spine matched arrows. But for the big game that I hunt
I don't take shots outside of 20 yards and
I really prefer it to be inside of 15 yards.
So at those distances I don't really need to worry that much about the spine.
If the arrows are making a bunch of noise or flying crazy
I'm going to go back and do the extra work to tune them to that specific bow.
But you'd be surprised how many times with just modest sized fletchings on
your arrows they fly great right out the gate. I
don't usually taper my arrows unless I'm having
arrow flight issues or I will maybe barrel taper a set now and
then just to mix things up. But I'm trying to stick to fast and good
because like I've mentioned before they're expendable ammunition to me
and I don't want to go through the extra steps to taper them
if they never needed it in the first place.
All right here are the tapering marks for
the jig. These are set at 6 inch increments
so 6, 12, and 18 inches from the backstop.
And you would taper them after you've already got the arrow
pretty much sized and round and smooth. So here we have a 3 8 poplar dowel.
It's already nice and round. We can pretend
that it's the arrows that I just sized to 3 8 from scratch.
And I'm going to take my Stanley thumb plane
that I leave set at a very fine cut so I can taper arrows.
And I'll do my first pass at the 6 inch mark.
And I'm just going to roll the arrow around
and take a pass off until I get all the way around.
So I'm rolling the arrow as I go to try to take an even amount off.
Now I've gone all the way around so I'm going to move back to 12 inches
and do the same. Notice how I'm going now from 12
all the way to the tip still. We want to taper the knock end of the arrow
more. Okay there's one full revolution at 12.
Now I'm going to move back to 18 and go over the whole thing
all the way to the knock. You can see the little marks that the plane leaves so
you know when you've made a full rotation. So now we have an arrow that's
3 8 at the point end and around the middle of the shaft it
tapers down to what I'm hoping will be 11 30 seconds.
And you can taper it as much or as little as you want.
But I'm going to go ahead and hit this with my
50 then 120 then 220. You can run this in the drill if you want to but
I don't think it's necessary. A little with the 50.
A little with the 120. A little with the 220.
Check it. Perfect. All I'm looking for is that the knock end fits through
that 11 30 seconds sizing guide and now I know I have a 3 8 arrow that is
tail tapered to 11 30 seconds. That's it for this video guys. As you
can see the ancient shooting board always has
been and always will be an excellent tool for
shaping split timber arrows. You'll see this set of arrows again in
chapter 5 when I choose a fletching style for them
and in chapter 6 when we put some points on them.
Thanks for watching.
