Welcome to another episode of To The Point,
where I help you become a better archer or bow maker
by getting straight to the point.
When tillering a bow, control is the most important thing.
The more control you have in the tillering process,
the better bow you can make.
It's that simple.
So when we're removing wood at the end of tillering,
you wanna have a lot of control.
How we normally do this is with a scraper.
Now there's a lot of different scrapers you can use
or different methods.
I'm gonna give you six methods of scraping off
a little bit of material,
and you may already have these tools at your hand.
And at the end, I'm also gonna give you two
or maybe even three bonus ways you can remove material
in a very controlled manner.
We'll start off with the traditional cabinet scraper.
I got this one for $5 on Amazon,
and it works really well as long as you keep it sharp.
How I like to keep it sharp is by using
600 to 800 grit sandpaper or a little diamond stone.
When sharpening this, all you need to do
is roll a bevel on the side.
I accomplish this by flattening out each side,
and then after it's flattened out,
hold the scraper vertically,
rub it back and forth on the sandpaper
or the diamond stone 10 to 20 times,
and this will roll a big enough bevel for you
so that you can scrape really good shavings.
Here's an example of scraping shavings
without it being sharp,
and here's a second example after I've sharpened it
that allows me to get perfect shavings every time.
The next tool I like to use as a scraper
is a simple pair of scissors.
This edge is actually quite sharp on the outside,
so you're not actually using the scissor blade,
you're using the edge on the outside.
What you can do with that is grab it like so
and just use it as a scraper.
It works very well, and you can sharpen this
pretty much the exact same way
as you do your cabinet scraper,
but you might have this one on hand.
The third item to use as a scraper
is just a good old pocket knife.
The one thing you wanna make sure with your pocket knife
that it is a fairly stiff one,
like if you had a bushcraft knife,
or even just something like this,
it's like a $20 Gerber knife.
If it's fairly sharp, it'll work good.
This isn't my favorite method
because it does dull the blade,
but if you wanna use this, you can.
If you don't mind sharpening your knife,
it works pretty good just to grab it
and use it as a scraper.
The fourth method is gonna be
the good old handy dandy draw knife.
All you do is put it up on in
and push it or pull it towards yourself
to remove shavings.
This method works really good.
The only downside to this, again,
is it's going to dull your blade some.
Now, if you work with Osage primarily
and you don't mind dulling your blade,
then it's not a massive deal.
Yet, I prefer to keep a sharp blade,
so that's why I use a cabinet scraper over this,
but this does work.
You can do everything with one tool if you need to,
and if you don't mind resharpening your draw knife.
The fifth tool I like to use is a razor blade.
This actually works really good.
You can get a pack of 100 of these for like $10.
Again, you can just grab it and scrape with it.
As you do more and more scraping,
you find the most optimized angle to get the best shavings.
The nice thing about this one
is that you can go up near the limb tip,
so you don't have to unstring the bow
during the end of the tillering process.
Now, the sixth tool is kind of a mix.
It is the razor blade again,
but I sandwiched it in this block of wood.
I screwed in a few screws.
This will hold this razor blade tight in place.
This allows you to get much better purchase
on this razor blade.
Once you find that perfect angle,
this method works really, really well.
Here are a couple bonus tips for you guys.
If you grab your normal cabinet scraper
and tilt it this way,
you can still often scrape with it.
Now, what this allows you to do
is get all the way up to the limb tip
without ever taking your bow string off
in the finishing tillering process.
So, near the limb tips,
I generally prefer to use little razor
or the cabinet scraper.
Next tip is if you like to use power tools,
get some 40 or 60 grit sandpaper,
and you can use this with your hand for final tillering,
or you can also put this on an orbital sander,
and it takes off wood about just as fast as a scraper will.
So, if you like to use power tools,
that's another really good method.
You could even go up to a belt sander with this,
but you would want to be careful with the belt sander
because the faster you remove the wood,
the greater chances that you will mess up.
I do recommend that you take caution
when you remove wood faster.
If you like to keep your draw knife sharp,
instead of using it as a scraper,
you can actually shave really thin shavings off
when you keep a super sharp draw knife.
So, you can basically use it as a scraper,
but take off slightly more material.
When you do this, though,
you're gonna want to pay attention to the wood grain
so that you don't split any out.
But it's definitely a decent method
to remove a lot of wood in a controlled method, but fast.
Another bonus tip is that you can use a chisel
as a scraper also.
I wouldn't use like a nice chisel set you have necessarily.
I would designate one chisel that's like your trash chisel,
but you can still sharpen it up
by holding it at this angle right here
and scraping on the back side.
It's super easy to get a purchase
and remove really fine shavings.
If I got to the point fast enough today,
please give me a thumbs up for the YouTube algorithm.
Also, if you need a bow string
or if you need a tillering string,
Shatterproof Archery is my company and the place to get it.
Remember, stay positive, be shatterproof,
I'm for you, and I'll see you on the next video.