Hi, I'm Mike with House on the Mend.
And in this video with our ongoing series
where we're rehabbing this house in Bullhead City, Arizona,
we're gonna be installing all the flooring in the bedrooms
with this, the new Ryobi floor saw.
So let's get started.
If you break it, he will fix it.
If you buy it, he will build it.
House on the Mend.
Now I'm not sponsored nor paid by Ryobi.
I bought this saw with my own money.
Let's unbox it and see what comes inside.
So this beautiful backdrop is our newly refurbished kitchen.
Let's open up our package and see what's inside.
Well, the first thing I noticed when I unboxed this saw
that was very disappointing was
they put this massive zip tie on right about here
to keep the saw from moving during transport.
So tight, as you can see here, it even crimped it,
that it cinched the wheels down on the slide rail
and actually flattened them out.
So now the wheels roll on here like a crappy shopping cart.
Watch this.
You hear that?
It actually stops and you can feel it hitting the flat spot.
Very disappointing.
They really need to rethink that.
They had a piece of styrofoam right in here
to keep it from moving.
They should have cinched that down instead of the rollers.
It can be done better.
Nonetheless, let's move on.
Overall, I think you're going to be very impressed as I am.
Now this fixed rail right here is what the saw slides on
and that keeps it going right in this groove.
The saw blade is going to be permanently 90 degrees
from the work surface.
Unlike a saw like this,
the blade can't be pivoted from the base.
It's no problem.
I don't know why you would want to do that anyway.
It's just something I wanted to point out.
The blade guard is very innovative.
It comes all the way down to protect your hands
and to protect the chips from flying out
and also to assist with dust removal, but it's on a spring.
So if you're using thicker material, look at that.
It just slides diagonally up out of the way.
So your work material would hit this little ramp
and it would just slide up out of the way.
Unlike a saw like this,
where you have this bottom piece
that you have to rotate to get your cut started
and then it rests on the wood the whole time.
So that's pretty neat.
So to make cross cuts, miter cuts, or rip cuts,
you're going to need fences.
And you might be wondering,
hey, this looks a little bare, where are they?
Check this out.
You flip it up and underneath you have a bunch of tools
pre-stored in little clamps for you.
So you've got your cross cut or miter cut fence.
This is going to be your rip fence.
When you're doing rip cuts,
it comes with a push stick
to keep your fingers out of the way.
And for changing the blade and making other adjustments,
you have these little combination Allen wrench
and Phillips head tools.
On both sides of the rail, you have these little screws.
These are gonna be for your fences
and they just stow away right there.
All right, the majority of your cuts
are going to be cross cuts or miter cuts
at the end of a run of flooring.
This fence has a little set pin
that goes right into place there.
Then you have this little guy that goes right into a slot
that will screw down and hold your flooring in place.
And then this little screw that we pulled out
goes right in over here and you can tighten it down
in anything from zero all the way to a 45 degree cut.
And when you look at the hash marks
for the 15, 22 and a half, 30 or 45,
there's a diagonal and then there's also
these little tails here at the end
that are kind of confusing.
Like which do you line up the fence on?
But if I take my speed square
and I set the 45 degree side,
you can see that on the 45, the 30 and so on,
you wanna set right on the diagonal line.
If I were Ryobi, I would get rid of these little tails
at the end, they just cause confusion.
The saw comes with a dust bag.
On the back of the dust bag, there's a zipper
so you can pull it off and dump out the sawdust
into a garbage can.
And then that fits right on this dust chute here.
But instead of using the bag,
I'm gonna opt for dust collection
with a cordless shop vac.
So the one I have, you pull off the little brush
and look at this, it's gonna fit right on there perfectly
and I'll be able to make my cuts
while using a cordless vacuum.
This tool didn't come with a battery
but I have plenty of my own.
So it just clicks right into place up top
and then on either side of the battery,
there's little tabs that you push in
to release the battery.
Now the little trigger has a safety
that you need to push up and out of the way
so that you can pull the trigger
and let's listen to what it sounds like.
All right, that's pretty loud
so I'm gonna be wearing hearing protection
the entire time I'm using it.
Now, let's pull the battery out
so I can demonstrate this trigger a little bit more.
This little button right here is the on lock.
So once you move the safety, pull the trigger in,
you can push in on the on lock
and the unit will run until such time
as you push the trigger, which releases that
and then release the trigger.
Now that's gonna be useful when we are doing rip cuts
and let's talk about that next.
So the majority of the time,
you are gonna be going across the room,
laying down the flooring
and when you get to the end wall,
you're gonna need to mark and cut that piece
so that it will fit towards the end wall
and then you take the remaining piece
and you start your course back at the front again.
But when you get to the end of the room,
you're gonna come to a situation in most cases
where you need a piece that is less
than the total width of the board
and that is a type of cut called a rip cut.
So let me show you how to do that.
First, we'll wanna remove the miter or cross cut fence.
Then we're gonna come in with the rip cut fence.
Same thing, there's gonna be two locator pins
that go right into this slot here
and that is gonna lock you in up to,
what are we like, four and a half or so inches away.
So let's just set it up someplace,
same pin goes in to lock it in.
Now, you no longer want the saw to freely move
so there is this hole right here
where a corresponding lock pin will lock the saw into place
and now you are set up for rip cuts
and you would come in here with your work piece,
slide it through the saw this way
to get whatever size you need to finish up.
Now, if you're worried about your work kicking back at you,
they have these anti-kickback pawls
that are spring-loaded, really aggressive teeth on them
and you just simply unscrew this little knob here
or loosen it, I should say, and set that down
so it'll grip the wood, tighten it into place
and now, as you're going through, if anything binds up,
it should hold it in place.
Now, personally, I think this laminate flooring we have
is so smooth that that's not gonna do anything for us
as far as gripping for throwback
so we'll just be really careful
when it comes time to make rip cuts.
I do like that right here behind the saw blade,
there is a riving knife
and a riving knife is simply a piece of metal
that is close to the thickness of the saw blade
and it's right behind so that as you make a cut in the wood,
both sides of the wood can't come back together
and start pressing against the saw blade.
That happens a lot with natural woods.
As you get the grain going through,
some pieces want to constrict like this
after they've made a cut and that can burn the wood
so the riving knife holds that cut
the same width as the saw blade the entire time
and keeps that from happening.
It makes for a cleaner cut.
Now, when it comes time to change the blade,
this blade guard has a little hinge on the back here
so it pivots out and each of these three screws
unscrew and allow you to twist the cover out of the way
to gain access to the saw blade and the arbor.
Now, the nice thing about these screws is they're captive
so they won't come out.
Now, the arbor size on this is 10 millimeter
and that's talking about the circular hole
in the saw blade itself.
But if you buy a replacement and it happens to be
the more common size of 5.8, that's no problem.
They supply you with this 5.8 arbor for those size blades.
So to remove the blade, just like almost all circular saws
and also angle grinders, there is a button right here
that you press in and that will lock the blade
so it doesn't rotate.
Boom, there it goes.
Now you can take your multi-tool that is included
and you go the opposite of the normal lefty-loosey,
righty-tighty because of the cutting direction of the blade.
So what feels like should be tightening
is actually loosening this screw.
So it's backwards threaded.
You pull off that little washer and the blade comes out.
And yeah, that is a really small little hole.
I would imagine most of the saws you're going to buy
will have a 5.8 arbor, but that's no problem.
You take this guy off and you set the other one
that comes with it into place.
Now, the first thing you wanna do
when bringing in your flooring is to cut open the boxes
to allow the flooring inside to acclimate
to your humidity level.
Next thing you wanna do is prepare your subfloor
by sweeping and or vacuuming it
to make sure there's no debris
underneath the eventual flooring.
After that, you need to choose an underlayment.
So for our case, we have concrete foundation,
therefore we need two types of underlayment.
We need a vapor barrier first,
and then on top of that, some sort of padding
to deaden the sound and cushion the walk a bit.
In most cases, you can buy an underlayment like I did
that's both a plastic vapor barrier and a foam padding.
Let's test out the saw by first cutting some spacers
out of this piece of scrap wood.
So take a look at these initial cuts
with the saw blade, very clean.
There's no chip out whatsoever on what was the top
and then the bottom surface, very clean.
So there's no right or wrong
which direction you have your boards run.
Personally, I like to have leading lines
leading me into each bedroom.
So I'm gonna start on this wall over here
and we're gonna work our way across.
So what you see right here is the casing
that goes all the way around the closet
and the closet doors actually come to close on this casing.
So rather than cutting back the flooring
so that we can push in tighter to the wall,
it's a lot easier to take a flat saw
or if you have a multi-tool
and cut back that portion of the casing
so you can slide your flooring board right into its place.
So to make sure we don't make any damage to the top surface,
we'll just flip this guy over,
set it right there on the spot and start cutting.
And there we go.
All right, let's set our first piece.
We got a spacer over here
against the back wall of the closet,
spacer here and a spacer here.
All right, we're over to the corner time
to make our first cut.
Now, I strategically planned out the length
of the first piece down there
so that this end piece would be at least 12 inches in length.
So you could just take that measurement
and transfer it over to your piece,
but once you get into a groove,
it is a lot easier to take the next piece,
flip it over, line it up and make your mark.
Then line up that mark with your saw blade and away we go.
And there we go, that piece fits perfectly.
You probably can't see it in the camera,
but here's our seam right here.
Now, the cutoff from this piece right here
becomes the first piece
and the next course down at the other end.
And now every single seam will be off by 12 inches,
which is good.
So with no help from Juno,
we're about halfway through,
287 square feet that we have cut so far.
And the blade is dulling to the point
where the sawdust is starting to burn
and it is getting noticeably more difficult
to push material through in table saw mode.
On one out of every two or three miter cuts,
the saw locks up halfway through the cut
because this locking pin here
that's meant to set it into table saw mode
is engaging on its own.
It is really annoying and a serious design flaw.
So we're at a point in this room
where the wall angles off at almost a 45 degree angle.
And we're gonna need to start cutting the boards
from this point on at that angle
so that we can stay close enough to the wall
where the baseboard will cover it.
So if we take this next piece and we slide it up here,
we can tell that right here is the corner
where we're gonna wanna start making that angled cut.
Well, Saker sent me this awesome tool.
You may have seen these before.
These are to help you with miter cuts,
but they're also very useful for this kind of a thing.
So if we set this against this wall
so that both sides line up just right,
we can see that for a single cut,
we are right at about 48 degrees.
So now I'm gonna line up right there.
And there's our cut.
And the next several courses
will also start with that same cut.
All right, so the max that this little miter saw fence
will go is just beyond 45 degrees.
But as you can see here, that's gonna be pretty close.
All right, let's see how we did.
Nice.
Room number two is done.
All these specialty cuts here at the end take time,
but I think it looks good, huh?
So as you come up to an end piece
that terminates at an unknown angle,
a very easy way to figure out just how to make this piece
is to go from this edge,
the showing edge of the previous piece,
and measure off to the wall, five inches there.
Come out here, ride right along this edge.
And we got 12 and a half inches there.
Then you take a fresh piece, come up to the exposed edge,
measure off of there, five, 12 and a half.
And there we go.
Now, besides Juno sitting in the doorway,
these are the things that also slow down our progress.
There is packaging glue from the box
all over the end seams.
And then these are all damaged from shipping.
So we are a little over halfway done
with the third bedroom here, the master bedroom,
not including the walk-in closet.
And for reference,
we are just finishing off our second battery.
So we've had one three amp hour,
one four amp hour battery depleted so far.
Now, while in table saw mode,
the saw has been sliding back and forth this way,
actually quite a bit.
The little feet don't really grip
this smooth flooring very well.
But my point is when you lift up the saw,
you can see this concentration
of whatever isn't getting picked up by the vacuum.
And the dust collection system.
So it is not flinging debris all over,
it's falling straight down.
So I really think they did a good job
in designing this dust collection system.
So after installing three bedrooms worth of flooring,
I think I've gotten a pretty good idea
of the pros and cons of this saw.
So let's go over them.
First of all, the pros.
Ease of use.
This saw is like most Ryobi tools,
very easy to use.
The button layouts and things are very intuitive.
I enjoyed using it.
Also the portability with the handle
and with the lightweight,
moving it around was very, very easy.
I love the fact that you can do both
your typical miter cuts,
which are your cross cuts.
And then also you can set up the rip fence
and do rip cuts all with the same tool.
Just fantastic.
The angle and distance markings are all very accurate.
Made it a lot easier to set up for angled cuts,
as well as setting up the rip fence for rip cuts.
The dust collection worked very well.
I really liked how low down the plastic guard
came on the blade,
allowing the little port back here to really do its job
in sucking up a lot of the dust and debris.
Now, with that being said,
I didn't use the bag that comes with it.
I used a small portable electric vacuum.
So your results may vary if you don't use a vacuum.
Next, the part storage.
Other than the little arbor that came with it,
if you have a different type of saw blade,
there is a place for everything on this saw.
And I think that's really well thought out.
I found the battery life to be really good.
Now on the box,
it claims a bunch of cuts with one battery.
That is a nine amp hour battery, which I don't have,
but I went through about two and a half
of four amp hour batteries.
I think I had one, three,
and two, four amp hour batteries that I used.
And as you can see here,
I've got about two bars left on this one.
I do think that the more ripping you do,
the less battery life you're going to have.
So if all you're doing is cross cuts, i.e. miter cuts,
the battery's going to last a lot longer,
but nonetheless, good battery life.
Now the cons.
And I actually only have three.
First of all, the blade quality.
Now, most Ryobi and Rigid power tools
that I've purchased in the past
have come with really good quality blades
that last a long time.
This flooring saw, however,
came with a very substandard blade that dulled quickly.
So about one and a half rooms in,
I noticed that the cut was no longer clean.
It started having a lot of tear out.
There was the odor of the flooring burning,
and you could see the burn marks on the cuts themselves.
So those are all indicative of a saw blade
that has gone dull.
I did actually end up finishing the entire three bedrooms
with the same saw blade,
but nonetheless,
I think it should have stayed sharper longer,
and that speaks to its low quality.
Next will be my chief complaint,
which is the locking pin.
This pin is meant to lock the saw
into a stationary position for doing rip cuts.
Now, I like that feature.
However, the design of the pin
just pivoting kind of very easily on its own is a flaw.
It should be corrected.
Maybe they could indent the plastic
or something to keep that pin
in more of a locked open position
so it's not constantly clicking into the lock position
as you're trying to go through the material
to make a cross cut.
Lastly would be the feet on the bottom of the saw itself.
I found that to be very slippery
when I had the saw in a rip cut mode.
So as I'm pushing the material through the saw,
it was sliding away from me,
and I had to concentrate
not only on keeping the laminate material
against the fence for a good clean cut,
but also in holding the saw stationary
so it wouldn't slide away from me.
I think it's kind of a safety concern.
Admittedly, I was resting the saw
on top of the flooring we had already installed,
which is very smooth flooring, but it's a flooring saw.
They should have anticipated that,
and I would like to see them
put some kind of more grippy material
or at least put a texture
or a softer type of rubber foot
so that it holds down on the laminate flooring better.
Now with all those things considered,
I would have no problem recommending this saw
to a professional or a DIYer.
It did a great job and definitely has a place
in a professional tool selection
and will be very convenient for you, I think,
if you install some flooring at home.
So if you found this video helpful,
will you please give it a thumbs up?
It really helps the algorithms
to start suggesting it to more viewers like you.
Also, please consider subscribing.
I'm working really hard to put out good quality content
and tool reviews, and there's more videos to come.
I'll leave a link for this saw
as well as everything else I used in this video.
Now, full disclosure, other than this saw,
which is available at Home Depot,
everything else will be Amazon affiliate links.
So if you click on them and end up making a purchase,
it won't cost you a thing,
but I do get a small reward at the end of the month.
It helps to justify all the extra time it takes
to set up the camera and the lighting and the audio,
to make these videos
during a pretty intensive bit of flooring install.
Speaking of intensive installs,
the next thing we're going to do
is install the baseboards in the house.
So I hope you'll tune in for that episode as well.
Until next time, thank you for watching.
Well, I had to reach over, and that all sounds stupid.