Hi, I'm Mike with House on the Mend, and in this episode of our rehab series on this house in
Bullhead City, Arizona, we are going to transform this very outdated kitchen from this to this.
So let's get started. If you break it, he will fix it. If you buy it, he will build it.
House on the Mend. So let's give you a quick rundown on this kitchen and what I want to do
with it. First off, this sink is, as I did in the original walkthrough episode, as I showed,
is chipped all over the place. Very old and unsightly, so I want to replace this sink and
the faucet. The countertops are fine. There's a couple little spots I might glue down some side
trim, but otherwise it's in pretty decent shape, especially for a rental. We've removed all the
old, way outdated appliances. We're going to put all brand new appliances in. I still need to clean
the walls and get all this goop off of here from years of cooking and cleaning and dust buildup,
but before I really clean the area, I wanted to remove the kitchen lighting here. This is your
standard raised ceiling fluorescent light bulb fixture with these diffusers that are plastic,
and they're kind of saggy. I really don't care for this look anymore, so we're going to take
all this out, and then after that we can do a real good deep cleaning. And as I said earlier
in one of the first episodes, I actually like the look of these doors as far as this kind of
farmhouse look with the what looks like slats going vertically and then these horizontal cross
braces. I think that looks neat, but what I do want is them to be painted, so we're going to
wash them down with TSP and get them spotless clean and then paint them. And I'm thinking of
a leaving this white background and then like a kind of a battleship gray kind of a look. I think
that'll look really nice in here. So let's get right into dismantling this whole lighting fixture
deal we have here. These little plastic sheets, you push them up and they slide right out,
and then this frame that goes all the way around is held in with some nails, and we're just going
to take a hammer with the claw on the back, pop those nails out, and then try to gently
get in with a 7-in-1 tool and get this framing material off and out of the way.
And then I'm thinking of taking out the ballasts that are just buzzy and flickery and such a hassle,
and I want to put in faux LED can lights. So they're actual LED, but they're not the whole
can that has to be installed from up in the attic. Instead, they can be flush mounted right to
the ceiling, and then I want to dress up this area here with some nice trim almost like door casing
trim to kind of accent the space. Let me get my respirator out of the way here so it doesn't
hit the microphone. We've got all four of the ballasts down, and fluorescent ballasts act as
their own box. And so we're going to need to bring this project to code and for our own safety and
to have something to mount the LED lights to, we're going to need to install boxes. So I went
and got these. I like the little ones with the wings that you screw down. The wings go inside,
pop out, but these have this little metal bracket on the back that flares out a bit, and you can use
a screwdriver to tighten them down once you push that in. So I marked the circumference of this
electrical box on a piece of like cardboard paper, and then I cut out for the wiring. I put it right
up here like this, traced around with a sharpie, and now we are ready to cut. Now there's all kinds
of power tools that are designed to quickly cut sheetrock, but in this case, since this electrical
wiring is right here, I don't want to damage it. Of course, the breaker's already turned off, but I
don't want to damage this wiring, so I'm going to cut by hand. Now that flanges out on either side.
We can take a drill with an extended bit, since it's way up in there, the screws, and we can clamp
that down into place. Well, the first coat's done and it already feels like it's brighter in here.
Let's put these LED lights up. So on the back side here, there's little spots for
screws to go into, and those correspond with the openings on this electrical box.
I really like these Wago connectors. They're so good. They're clear plastic. You can slide the
right up to the spot where the insulation is prior to the clamp, so you know you're not
going over and actually clamping onto the insulation. There. Then we'll just rotate it
into place. Good. Got one more, and then we can turn it on and see how much brighter it is in here.
All right, let's give it a look. Yes, look at that bright, clean light. This is 5,000 Kelvin, so
very, very white, cool light, they call it. All right, so the final thing to do up here is to
trim out this junction where the box meets the ceiling here. So we'll start with the strip
going this way and then finish it out with a strip that's mitered going all the way around.
That's going to look nice. I really like the way these lights turned out. It's such a clean look.
So now let's shift our attention to the cabinet doors. I want to remove all the cabinet doors,
wash them all with TSP and a scrub brush to degrease them really good, and once that's done,
then I'm going to wash the cabinet bases themselves and the walls. There are some
spots like where the stove and the microwave were and the refrigerator that the paint is
a different color, and there's a lot of grime from cooking over here. So I'm going to scrub
all this down really good and just paint the whole area that you see here white,
and I just think that'll be a nice clean look. It won't seem like it's unfinished right here
where all this splatter is. All right, let's take these off. All right, when it comes to the doors,
I want to mark them so I can keep track of where they all go because they're probably
not going to line up properly if you don't do that important step. So right here where the
hinges were, it doesn't matter if there's any paint there because the hinges are going to go
right back on and cover that up. So that's why I like to take a small piece of painter's tape
and this sharpie and mark them so I can keep track of them. So this is the kitchen. These are the top
row of doors and I'm going to, so I'm going to go KT, one, two, three, and so on around, and then KB
for the bottom in the kitchen all the way around, and that way it'll be a lot quicker to just slap
them all back on when it's time. Let me get the rest of these off and we'll start cleaning them.
About 90 percent of these hinges are broken, meaning that this plastic piece that retains
these springs is breaking off and the springs are just popping out everywhere as I take them off.
And what those do is hold these hinges closed so the doors stay close to the cabinets themselves.
And you can see that has also happened here that this one has broken and thus they installed a
magnet and a little clasp here to keep the door closed. So we're gonna have to
replace all these hinges for ones that aren't rotted out. Well it's time for everything to
get cleaned. Well this cabinet door looks like it absorbed the frag from a ketchup grenade.
Well that's the entire count of 30 doors done on one side. I let them dry overnight and now
I've tacked everything clean and we're ready to do the other sides. I would have to say the
biggest challenge with painting the first side was not getting my own sweat dripping off of
my face because we're in this hot sunroom falling on the fresh paint. So if you see me bending down
like this to lay down the cabinet door it's because I'm trying to avoid that. All right,
back at it. We're back inside today with a nice reprieve from the heat.
Let's get to painting these cabinet frames. Next step is to clean all these drawer fronts
with the same TSP 5-in-1 tool to scrape off all this old ketchup or food product whatever it is
get them ready for paint. All right, that's quite a pile of drawers. So once these dry I'll tape
them off and we can paint the fronts. And these are shelves that go over in the pantry so I'm
to see if I can't sand some of these stains out of them. What do you think? Does the TSP have a
rough effect on these rubber gloves? Well the paint's all dry on these drawer faces and they
turned out great. Time to take the tape off but rather than just peeling it straight off and
risking pulling up some of the paint off which is really unsightly I like to take a razor blade and
just score that edge. That way we get a nice clean break. All right, then I also have these
little clear bumpers that I'm putting on so we don't have paint on paint contact that could
make it sticky. Perfect. So I got this box of cabinet hardware off of Amazon. It comes with
bumpers and then all the screws that you'll need. And if we look here they're almost an exact
copy. Just a little bit off that way but all the holes are going to line up nonetheless.
Let's peel back this tape and see which door this is. Kitchen top 10.
Well today is a big day. We are going to be replacing this white porcelain chipped up sink
and really heavily corroded faucet with this brand new stainless steel sink.
This beautiful updated Moen faucet. Brand new drain piping and brand new garbage disposal.
So first thing to do is disconnect all of this plumbing that's existing. Get underneath,
disconnect every mounting screw that's holding this old sink in and then very carefully remove it.
So here's a great tip. Rather than installing the sink first and then having to uncomfortably lay
underneath it to attach everything, way better to set it on a countertop. I've got a moving blanket
here to protect the stainless steel from getting any mars or scratches. And build up the drains,
the garbage disposal, all the piping, the faucet, any plugs, anything else that you have to do
right here at a nice comfortable standing distance. So that's what we're gonna do right now.
Well it's not every day I get to mount a microwave without the stove being right here in my way so
I'm looking forward to it. Got our template all set up here for where the
bottom piece goes that holds the microwave in place.
Well I got the gas line for this stove all hooked up but before I plug in the
power cord I want to first charge that gas line and do a leak test. And the normal totally
acceptable thing to do is just to use dish soap, put it in a spray bottle, or dab some soap and
water on a brush and see if you get any bubbles. But this GE oven comes with this little vial of
fluorescent leak detector so I'm going to try that out. Well what a difference we've made in
this kitchen. I'd have to say the most striking thing is the stainless steel appliances. Just a
nice updated clean look. I love the fact that we have a functioning microwave up top over the
range rather than the range hood that used to be there. Just a must in today's kitchens in my
opinion to save countertop space. The sink is matching stainless steel and we've got a brand
new faucet. Just a beautiful complementary look. Of course the cabinet paint is among my favorite
colors. I just think that kind of battleship gray with this slightly bluish hue to it as well
really contrasts well against the white walls and complements the appliances. And then finally
the lighting. What a difference from those really old ballasts and the plastic pieces and the
flickering and the noisy buzzing to this clean silent but nice bright white lighting. It's gonna
make cooking in here just a pleasure. So if you found this video helpful will you please give it
a thumbs up. It really helps the algorithms to start suggesting it to more viewers like you.
Also please consider subscribing. I'm working really hard to put out good quality content and
there's more videos to come. I'm gonna leave links for everything that we talked about and the tools
that I used in the description below. Full disclosure those are Amazon affiliate links so
if you click on them and end up making a purchase it won't cost you a thing but I do get a small
reward at the end of the month. It helps to justify all the extra time it takes to set up video and
audio and lighting for a project of this scale. Now speaking of this project our next video is
going to be on flooring. So I have a great tool that we are going to review that's helping out
with that flooring and I can't wait for you to see that video. So until next time thank you for watching.