I'm Mike with House on the Mend and this is episode two of our hybrid work and travel
family life van conversion. In this episode we are going to take this 3M Thinsulate insulation
and start insulating the walls and the ceiling of the van. We're also going to get underneath
the headboard and put some sound deadening there as well as in the area where the bed is going to
be the head and the feet. We're going to put some thinner Noiko insulation there in preparation for
carpeting those areas. If you like this video and find it helpful will you please give it a thumbs
up. It really helps the YouTube algorithm to start suggesting it to more people. Also please leave a
comment or a question below if I'm not addressing something you'd like to hear. I'm really good at
responding to questions on my comments on my videos. So with that let's get started.
All right let's get this cut open here. Now this is 3M Thinsulate and it's really good for
van builds like this because it resists mold build up at all and also it's not made of fiberglass so
you're not going to be scratchy and itchy in your living area. So this appears to be
once it uncompresses a little bit initially it's about inch inch and a half thick
about an inch so we'll see if it expands more than that. I've heard that in some of the other
videos I've watched that this stuff is tough to cut so I thought maybe we can start by using these
shears that did an excellent job on the kill mat and if that doesn't work move on to razor blade
and a few other things and see what works best. Now I figure we may as well start right here at
the doors and move forward so let me get a measurement. Oh these shears work really good so
far. All right maybe once it expands more it won't cut so well with these but so far they're awesome.
When I go in to the door I want to get right to this spot where there's this piece right here.
Several of the pieces that I have cut out already that slip right into these little channels of the
doors or up here in this long skinny channel they're just fine but all the rest of these you
can see are just flapping down. They're not going to stay put. I had some temporary blue painter's
tape put up just to hold them in place but that didn't even hold so what I'm going to do is use
this spray adhesive. This particular brand is Loctite here and it says it needs to be about 65
degrees and that you should spray both surfaces for good adhesion. Let them both sit for a minute
and then they act as contact cement and should go together real good so let's do one together. I've
got the little table set up right here with an old box that we're going to throw away so I don't get
sticky stuff all over my little table and I figured rather than doing it inside here and taking the
risk of getting adhesive on the floor we'll spray that outside and then I can just spray this area
right here. Got a nice breeze going this way so I've actually moved the camera quite a ways down
and just zoomed in. All right we'll let that sit for one minute. Oh yeah that's holding real good.
All right that's going to work real good. I'm just going to repeat those steps for all the pieces and
that's going to take care of our first roll. I'm waiting for the second one to come in the mail.
The next thing we can work on is put some of that Noiko insulation right here on this area
where the bed's going to go where we filled the space with kill mat. So we'll do that next. All
right what we have of the thinsulate that needed to be glued has all been glued in with that spray
adhesive and now let's turn our focus on to insulating this area with this Noiko product.
That's n-o-i-c-o. I'll leave a link for it. It's available on Amazon but they say you have a base
layer and then you put down this 150 mil heat and cool insulation as a second layer and that's
we're going to do. So my vision is to have this nice soft little insulation come right up and
actually round this corner on this strut just like that. When this piece goes here the next piece
will come right over here and will round out perfectly and then we'll eventually put like a
small carpet covered piece of quarter inch plywood there to dress that out once everything's
carpeted. All right so let's get going. Set this piece here and that way I can start peeling the
backing. I dig into that corner so we get a good tight look on there. All right now we can still
see the line where the kill mat meets this trim piece but that's okay because I've ordered eighth
inch closed cell foam upholstery foam right and that's going to be one more layer that'll go here
before we put the carpeting on and that should help to further dilute any of these lines that
we see. I think that turned out pretty good. All right one two three more to go.
So I learned from this seam that it's probably better to put some tape up first before you cut
because all this tore off here even after I cut it with the razor and I'm gonna have to clean that up
so I got smart and on this side I put up blue painter's tape all the way around the corner
then when I was done cutting with the razor knife we get this satisfying peel off here
and that's a whole lot better. All right we're all the way done. Back to this last piece right here
that's right by the headliner and I wanted to leave that piece off until we got in to this
headliner got in there and put some insulation in but what I found out was one of these tools here
for the door trim removal tools are really necessary and work out really well for these
guys because they have two kind of Christmas tree looking points that go in and you need to
squeeze those together for the piece to come out and not get broken.
So for instance if we come in right here and we start pushing in and we squeeze those two together
like that then it comes out in one piece which is great because until I figured that out I broke
two of them pretty badly and the other two a little bit broke off but they were still usable
but if you can pinch them together like this that works really good. So once I got all those pins
out I was able to pull the headliner down to about right here and as you look across the roof you can
see all the wiring for the lights that go across the front of the roof of the Dodge Ram ProMaster.
So there was enough room in between those lights that I cut kill mat into thirds and was able to
get it up into place. The problem was when I started trying to get the roller down there I
wasn't able to get the proper amount of leverage like we did on the walls and on the ceiling.
So I don't think I got an effective sound deadening bond with the
kill mat. You might want to try the Noiko or something that you don't have to roll into place.
Nonetheless I have a total of one sheet up there. A third here, a third here, and a third over here.
It just wasn't rolled very effectively. Then I cut a 50 inch long by 10 inch wide piece of
thinsulate and I was able to slide that into place push it up and then get all these
little buttons right back into place except for the two that I broke. So oh and do yourself a
favor when you're going to put them back in make sure that the the hollow area is facing you so
that these two can pinch together if you ever need to get in there again. Say if you want to
put in a special some wiring for a special rear view mirror camera or something else but
those just pop right back into place. I'm going to have to order these two replacements but that's
no big deal. Now it's time to put in the final piece of thinsulate up on the ceiling and earlier
I said I wasn't too sure if this plastic was effective but as I look across it I can see all
kinds of little fibrous remnants of the spray adhesive so this really was a good idea. It
captured a lot of the stuff coming down that would have otherwise landed on the floor on my shoes
and clothes and tools so I do think that was pretty effective. All right we're going when we
come back we're going to have this last piece in that will complete all the insulation. Remember
we're putting a window here and a window here so we're not going to have any there but the rest of
it is all done and we're going to go on our third ride to check for road noise. All right ride number
three, same route, same speeds, only difference this time is Juno is with us. She wanted to go for a ride.
Well in my opinion the addition of this 3M thinsulate really deadens the sound back here
when as I'm talking I don't hear any echo whatsoever. It's almost like a sound room back
here so a dramatic difference and I had mentioned at the beginning when I first unraveled that
the thinsulate was about an inch and I wondered if it would expand. I would say it expanded to
about one and a half times its size maybe about an inch and a half or so. So it's been several
months since I've installed all this thinsulate and I started noticing that the adhesive on the
ceiling was starting to give way in several spots so I ended up taking just regular old like cotton
twine that I had at the house and ran through all these cross braces to hold everything in place
and that has helped tremendously and if you consider the timeline of a build like this
it's going to be a while from the basic sound deadening and insulation to the time where you're
running the wiring for the lighting and then finally getting into putting in the roof panels
or ceiling panels. So I would advise this if you're just going to use spray adhesive. It will
keep everything in place and be a lot less hectic for you. So if you found this video helpful will
you please give it a thumbs up. It really helps the algorithms to start suggesting it to more
viewers like you. Also please consider subscribing. I'm working really hard to put out good quality
content. There's a lot more videos to come on this van build as well as tool reviews and other things.
I'm gonna leave a link for everything I discussed in this video. Full disclosure those will be
Amazon affiliate links so if you click on them and end up making a purchase it won't cost you a thing
but I do get a small reward at the end of the month. It helps to justify all the time it takes
to set up camera angles and lighting and things to record these videos. Speaking of our videos the
next one is going to be on these seats that I chose for the back area of the van right behind
the driver's seat. They come complete with their own seat belts and a really cool adjustable spring
ride suspension that is really nice. Arm rests and how I built this pedestal that they're sitting on
complete with its own storage drawers and USB ports to charge your devices. And that brings
us to the final point of the video where we discuss the cost of each item we added as well
as the weight. The weight is significant because we have a total payload in this Ram Promaster 2500
of 4,000 pounds so I want to keep track of what we're adding to it. So in this episode it took
two rolls of the 3M Thinsulate for a total of $412.30 pounds, three cans of the Loctite
Adhesive Spray at $25 but only about a pound worth of glue. That subtotal is $437 and 31 pounds.
If we add that to episode one's totals we get a grand total running so far of $1,055
and 255 pounds added to the van. Until that next episode, thank you for watching.