In episode six I demonstrate the transmission adaptation relearn procedure on our 2006 Land Rover LR3 using the GAP IID tool. This procedure is used to relearn adaptations after a transmission service or replacement.
Hi, I'm Mike. Welcome to my Waffle Square where I obsess about things and you get to benefit from
them. So in episode six of our ongoing series where we are refurbishing this 2006 Land Rover
LR3 with the V8 petrol engine, we are going to be performing the transmission adaptations
relearn procedure. I know it sounds like a mouthful but it's very important. So in episode
three where we did a complete transmission service on the 6HP26, I made this statement
about how I was going to drive the vehicle after clearing the adaptations. Now over the next
several weeks, as the computer is learning how to properly shift the transmission now that it's
been fully serviced, I'm going to be driving it like a grandma. Just kind of around town driving,
nothing really getting on, no heavy acceleration, no pulling any trailers, climbing up the mountain
to Mount Charleston, anything like that. Just kind of around town driving to let the computer
start to learn again the proper way to shift it. Well thankfully one of my viewers, NE0N3,
reached out and said, Mike, there is a specific reset procedure after resetting adaptation values.
Don't just drive it like a granny. The BMW guys are a wealth of knowledge on the ZF6HP26
transmissions. You can see a video of the procedure here. And he ended up sending me links to two
YouTube videos that I will link in the description below talking about the exact procedure for
resetting adaptation values on these transmissions. So if you look in this blog that's a link to one
videos, I will also link this website below. You'll see that there are basically four procedures
for resetting adaptations on BMW vehicles. Now I couldn't find a specific link for Land Rover LR3,
so if anyone knows that, send me that information in the comments below and I'll just reproduce
this video. But these four adaptation reset procedures, A, N, P, and T, are linked to this
blog. So as you can see here, procedure A seems to be the most basic with just one step that you
repeat nine times. At first I was going to go with that procedure because every other one talks about
using a Steptronic to manually shift the gears. Now the LR3 does not have a Steptronic, so
originally I thought this must be the one. However, upon closer inspection of our transmission gear
shifter, as well as reading the manuals, we'll show you there is a very similar selector that
Land Rover calls Command Shift. So since Command Shift and Steptronic are basically the same thing,
I'm going to go with one of the other three. Now as you can see here, procedure P actually is for
the 6HP19 transmission, which we don't have, so that one is canceled out too, leaving N and T.
Now N and T are very similar. In fact, there's only one slight difference in Step 2, which is
whether or not you go manually down to fourth gear or third gear. So I couldn't find with the
GAP tool anywhere what software we have, what version of any firmware, or anything for the
transmission like we easily did with the air compressor. Therefore, when I look at T and I
see that it's for T software and I can't find anything linking T software to the Land Rover,
I'm just going to go with procedure N. So I printed out procedure N here. There's three
steps to this procedure, very involved, very detailed. We're going to run through them and
see if it improves the way our transmission is shifting. So in order to successfully perform
this procedure, you are going to need the GAP ID tool or something similar to it. The GAP ID tool
is an ODB reader. It plugs into the ODB port of your Land Rover LR3. It is specifically designed
for Land Rovers and Jaguars, and we're going to need it for two reasons. Number one, when we get
out to the location I have chosen to perform this procedure, we are going to clear all the
adaptations. Number two, live values. So we are going to need, as you see in this screenshot,
to know what gear we're in, what speed we're at, and the temperature of the transmission
fluid. As you can see in the procedure here, you are going to need to first start the adaptation
relearn with the transmission at operating temperature. That's basically anything above
40 degrees Celsius. Just before beginning, we'll need to clear the adaptation values,
and then we're going to drive the vehicle in various speeds and various gears and shift back
and forth between neutral drive, neutral, and reverse in order to complete the procedure. Now,
before we get going, there was a few things I needed to do to the vehicle to make it safe to
roll on down the road. Number one, I reattached the cover for the air compressor. I put back all
the screws and panel clips around the passenger side wheel well, where the front valve block was
located for the air suspension. Torqued down all the lug nuts to 103 foot-pounds and checked the
PSI in all four tires. And I went on eBay and I purchased a used replacement DVD player for the
headliner in the back seat, since the other one wouldn't close and that would obstruct my view
when we were driving. Finally, I went to the gas station and filled up the tank. So getting some
fresh gas. And were you aware that the manual says this vehicle needs 91 octane? It said it can run
on 87, no less than 87, but it'll have performance issues. All right, we are all set up and ready to
go. I've got the gap tool installed and I've got my mini iPad right up here in this perfect spot so
we can do the live readings. Now, the first thing I want to do is clear our adaptations. So we drove
from the house here to this spot and it started obviously setting its own adaptations. We want to
clear those once we are up to operating temperature, which I'll show you in a minute, we are. So we're
going to go to service test, transmission, clear adaptation values, proceed, yes. It says engine running,
turn off engine and return ignition on. Executing routine, clearing faults, operation succeed.
All right, now I'm going to start the engine back up and now we can go into live values because this
is going to become important here in a moment as we are getting up to the proper speed, making sure
the temperature is correct, and making sure we're in the right gear. So let's go to live values and
we're going to go into select live values, quick list. Now I'm going to go into the engine first
because I want vehicle speed. At the very bottom of engine for live values is vehicle speed.
Now I've got that set at miles per hour because the sheet that I have is in miles per hour. Now
we're going to come out of that. We're going to go into transmission and there's two I want for there.
Transmission oil temperature and current gear. All right, full screen here so we can see
the most important ones are vehicle speed and the transmission gear for setting the adaptations.
I have the transmission oil temperature up because it is vital before you start this test
that the transmission be up to operating temperature, which you can see here that we are.
All right, so what's the first step on our list? It is from a standstill, accelerate the vehicle
very light throttle to fourth gear. Continue to accelerate with light throttle to sixth gear.
Let the vehicle coast to 25 miles per hour, then slow to a standstill with light brake application.
With the brakes applied and the vehicle at a standstill, wait for 10 seconds.
And we're going to repeat that nine times. So let's get started. All right, we're clear.
First gear, second gear, third gear. It's working up third gear. There we go. There's fourth.
Now a little tiny bit more throttle just to get us up. There's fifth gear and there's sixth gear.
So now I'm going to take my foot off the accelerator and we're going to cruise down
to 25 miles per hour and then slowly come to a stop. And transmission cycle itself down to fifth
gear, down to fourth. Put my blinker on here because I see a couple cars, but that's going
to work out all right. They'll pass us by the time we count to 10. And there we are below 25
miles per hour. So I'm just going to pull over and let these two cars go by as we count to 10.
1, 2, 3, 4, 5, 6, 7, 8, 9, 10. All right, one more time. Actually, nine more times.
All right, we've done that 10 times. I will say that in the first few times of doing that,
I felt that it struggled from third to fourth gear. So it it wind out a little longer and then
when it finally went into fourth gear, it was a little bit of a almost like a lug, like you could
feel it finally give. But after the fifth one, that really settled down. And so it's getting
smoother already. It's learning. So for step two, we're going to accelerate to 45 miles an hour
using the Steptronic to select the fifth gear. Remember, we don't have a Steptronic. We have
what they call the command shift. So all the way up to fifth gear, then with light throttle
application, accelerate to 60 miles an hour and then let the vehicle coast to 40 miles per hour.
Without applying the brakes, repeat this sequence four times. Accelerate the vehicle
to approximately 55 miles per hour. Use the Steptronic to select sixth gear. With light
throttle application, accelerate to 65 miles per hour. Then let the vehicle coast to approximately
50 miles per hour without applying the brakes and repeat this sequence four times. Use the
Steptronic, or in our case, the command shift to select fourth gear and repeat step two from
the beginning. And we've got to do all of that five times. So let's accelerate to 45 miles per
hour and I'm going to use the command shift. We're in fourth gear. Accelerate to 45 miles per hour.
Then we're going to use the Steptronic to select fifth gear. There's 45. Fifth gear.
With light throttle application, accelerate to 60 miles per hour.
There's 60. Now we're going to let the vehicle coast without applying the brakes to 40.
There was 40 and we're going to repeat this four times. So back up to 60. All right, there's four
times of that. Now we're going to accelerate to 55 miles per hour. Use the command shift to get us
into sixth gear. There's 55. There is sixth gear. With light throttle application, accelerate to 65
miles per hour. Then let the vehicle coast to 50 miles per hour. Well, this engine's sounding good.
There's 65. Now I'm going to coast to 50 miles per hour. Let's see if I can get this car behind
me to pass us. Come on, son. No? All right, there's 50. Let's go back up to 65 and we're going to do that
four times. So that was one and there was the fourth time up to 65. So now we are coasting
down to 50 miles per hour. Then I'm going to use the command shift to select fourth gear
and we're going to go right back up to the beginning of step two and do it all over again
five times. All right, all done with step two. One step left to go and this one we do from a standstill.
So from neutral with the vehicle at a standstill shift from neutral to drive. Wait five seconds
then shift back to neutral again. Three, four, five. With the vehicle at a standstill shift
from neutral to reverse. You can see reverse come up on the live feed. That's cool. Wait five seconds
four, five, then shift back to neutral again. We repeat that four times. Well, after all that work
let's see how we're shifting. Your second gear smooth into third, third to fourth.
Oh, real smooth. No hesitation. So that is better for sure. All right, well everything's good so far
but I've been doing really slow acceleration. What do you say we come up here to the highway
and give it just a little kick and see how it does? All right, here we go from a dead stop.
Third gear. Oh, good acceleration. Still in third. There's fourth. There's fifth.
We're doing about 75 right now. Put it back off. Up to sixth. Smooth. Nice.
So I think it goes without saying that in my opinion that was a hugely successful outing. The
vehicle drives so smooth now. In fact, I came home, got Aspen and we took a drive down to
Prim, Nevada which is the state line between California and Nevada and the vehicle just ran
great. The air suspension was smooth just like floating on clouds. It was a great experience.
I would definitely recommend that you leave yourself ample time. This video has been heavily
edited but that took a couple hours of driving around and I would also recommend that you find
longest open road, not heavily congested, that's as flat as possible because step two
involves long distances with no braking. Let's go over some comments from the previous video.
So Florian Rave and Gary Stewart both said the F26 fuse is the one to remove to perform the
overnight leak test on your air suspension. Great tips guys. I certainly appreciate you
helping out the channel. Brysher Bird asked this question. What about stiff suspension?
No leaks. One minute it's soft. Next time I start my vehicle it's stiff. I said if it's completely
down on the bump stops or too high the ride will be stiff. He replied but it's on normal
at these times when one minute it's soft and then one minute it's stiff. I don't know if it's
something with the sway bar or the air suspension. It's becoming very frustrating. If anyone knows
what might be going on with Brysher's vehicle will you please help him out either in the previous
episode's comments or the comments here and I'll make sure they get back to him. Thank you for any
help in advance. Paul Watson wrote in. Big shout out to you from Jamaica. Love all the work you're
doing. Keep doing the great good work kid. Don't worry about the haters. Just give thanks to the
motivators. Cool. From Jamaica. Paul your comment made my heart happy. Thank you very much. So if
you found this video helpful will you please give it a thumbs up. It really helps the algorithms to
start suggesting it to more viewers like you. Also please consider subscribing. I'm working
really hard to put out good quality content and there's a lot more videos to come on this vehicle
even though we finally got it running. I also want to give a special shout out to everyone who has
subscribed since the last video where I pointed out that 95 percent of people that were viewing
these videos weren't even subscribed. And a special shout out to Gunder Thoretson who as you can see
here was our 1000th subscriber. It really is so helpful if you'll do that little thing and subscribe
on YouTube or follow on Rumble. It's free. You just have to log into the account and click subscribe.
Thank you to everyone who has done that. The more subscribers I get the more it will be capable for
me to start investing almost full time into my YouTube channels which would be great and result
in a lot more free content. Now while we were driving the vehicle I did notice that the air
temperature coming out of the heater was nice and warm on the passenger side and completely cold on
the driver's side. Now it's possible that could be the blast doors one of them stuck inside of the
dashboard area when you turn on the heat but when I went on the Land Rover forums I did find this
post and everybody on there was saying that it is most likely a clogged heater core and there is a
pretty easy procedure to flush out that heater core and we're going to do that on the next video
because when I replaced the water pump I did find this gray solution all around the water pump that
made me believe somebody had put stop leak in the vehicle and maybe some of that has clogged that
heater core. So that's going to be our next video. Until then, thank you for watching.