MY GIRLFRIEND BOUGHT A WRECKED LAND ROVER DEFENDER

Ex Used Car
15 followers
69 Video Views·Feb 19, 2026
My girlfriend just bought this wrecked Land Rover Defender and she thinks she can rebuild it.
After five years of watching me rebuild cars, Hannah's finally decided to give one a go herself.
And she shows this, the new Land Rover Defender, which at first she thought was quite minimal
damage, chassis damage, but it turned out to be hiding a lot more than she originally thought.
But as she bought this car blind from an online auction, there's always that risk involved.
And now she's committed to rebuilding this car with hopes that she's got herself a bargain.
I found it, I bought it.
We're hoping, well you're hoping that it's not too big of a repair.
First fix, and I did that, I didn't force you for that one.
We've got dents on this side though, dent here, dent here.
Is this missing an arch as well, like a wide arch?
Is that what we're missing?
So this is a standard Land Rover Defender, how they leave the factory.
But the one that Hannah's bought has or did have an urban kit fitted to it,
which should look like this.
But the problem we're going to have, it looks like some of the urban parts are missing or damaged,
which means we're going to have to buy them as well to fix this one.
So basically we're missing an urban arch here, so we're probably going to have to bring urban
to see if we can get that.
And it looks like the same is missing from the right hand side.
Oh, I think there's something missing out of here as well.
Definitely something missing out of here.
It's all got like hair and like sticky stuff.
Oh, it's been used in here, hasn't it?
Very well.
Yeah, but this is what these cars are for, it's like a workhorse.
That's true.
We've not quite got to all the damage yet, but one thing we want to make sure
is that the engine runs.
This is the three litre diesel one.
It's one of them cars as well, where you can't check the oil.
Yeah, you can.
Oh, has it got a dipstick?
Yeah.
They did something good.
Yeah.
Right.
Oh, it's got oil in it.
Good news there, we should be good to start it.
Do you want to start it up and see if it starts?
The battery is dead, so Hannah had to put the jumper pack on
and then we could give it a start.
Okay, go and see.
Yeah, first time.
Very smooth.
That runs well smooth.
This is a cruiser.
How many miles?
62,000.
And for a 2021 Defender, with that sort of mileage,
you're looking at over 60,000 pounds.
So, so far, things were looking good for Hannah.
Low engine light.
So far, so good.
It's a proper farmer's car, isn't it?
The dashboard was clear of faults and it was looking like an easy fix.
That was until we started looking into the wheel arch.
Chassis damage.
The chassis behind the front wheel looks like it's taken a really big hit.
So maybe this wasn't going to turn out as easy as Hannah first thought.
But there was no point in us trying to see the damage
whilst it was on the trailer here,
so we needed to get it inside the unit
so we could lift it up in the ramp to inspect that damage further.
I've never put a car in the ramp before,
so I just feel like it'd fall on me.
After all, this car is a Category S,
which stands for structural damage,
and I think we've just found it.
What has happened?
The wheel's gone back and hit the frame of the car,
like that Merc did.
That's a lot of pressure.
But it's good that the wheel's broken,
because if the wheel didn't break, it would have broke something else.
If the wheel was really strong, it would have broke more of the chassis.
I mean, it's a massive wheel as well.
Now we need to inspect the damage.
You can never truly see how much damage an accident has caused
until you start stripping the parts around the damage,
and that's exactly what we're doing now.
Out comes the arch lining, that'll need replacing,
and then we can just take a look at the chassis damage inside the wheel arch.
It's still pretty hard to see exactly how bad it is.
Your job, get the suspension off and the brakes.
You can be the tool boy.
Thank you.
Oh, that's a death bolt.
More of the suspension is being taken off.
Hannah's removing the brake caliper,
and her and my dad were going to tie it up on the shock absorber
until they realised they were going to be removing that later.
So instead, they clamped the rubber hose to stop the brake fluid leak
when they unbolt the brake line from the actual caliper
so it can move it away from the car,
but it still looked like the brake fluid leaked everywhere.
I'm not even making it better.
Next up is the brake disc.
There's only one bolt which holds this to the wheel hub,
then off it comes.
We think it's more than likely that this is going to be bent
because it's had a big hit and it's aluminium.
So we're going to replace that, but also check this out.
This part of the subframe has broken away,
which is going to be another big job.
But to get to it all, we've got to remove all of this.
First up, the driveshaft.
This huge nut here is coming off, which holds it to the wheel hub.
My dad loosely screwed it back on so then Hannah can hit the driveshaft
without damaging the threads on the end.
Then it should pop out the wheel hub.
The only thing holding the wheel hub to the rest of the car now is one lower arm.
Hannah undoes that nut there, then the wheel hub can be lifted off.
That'll definitely need replacing.
Then the anti-roll bar droplink can be disconnected from the shock absorber
and the shock absorber unbolted from the lower arm and from the subframe as well.
What are we doing now, Hannah?
We've got to disconnect two wires and then there's four bolts.
And once they're undone, the whole shock absorber should be able to be removed.
Now this big heavy car is on air suspension and this part here,
which Hannah's undoing, is the airline which goes into the suspension.
Once she's disconnected that, there's then four nuts which are holding the shock absorber on.
Are you enjoying yourself, Hannah?
I'm having a great time.
I feel like I am really confident with this stuff.
Yes, I am slower, but I don't do this every day.
And so far, so good.
Don't drop the nut.
Too late.
Out that comes.
And to be honest, this damper doesn't look too bad and they are expensive,
but there's some parts we won't get away without replacing.
On to the next step.
Up in the air, under tray's off.
Disconnect this side off the subframe without actually disconnecting too much.
The goal is to get the subframe off now
because there's some bad damage to it on that right-hand side
and we're not going to be able to fix it.
But there's a lot of things which connect to that subframe.
You can see the damage here.
First thing to disconnect are all the arms which are on the left-hand side,
which are going from the hub to the subframe.
Then this part of the front bumper comes off.
After that, Hannah's removing the front wheel
so she can remove the front arch lining on the left-hand side
because once you get this out of the way,
you can then take the bolt out for the arm.
That's the suspension disconnected on the left-hand side.
Now my dad's disconnecting the steering rack from the steering column
because the steering rack is actually going to come down with the subframe.
And last but not least, the drive shaft.
Hannah's just pulled this out of the front differential.
Now we can go back to the top of the engine.
We need to support it.
Okay, what we need to do now is hold the engine up here
so then the subframe can go down.
And to do that, we're going to be using the engine support bar.
This goes across the engine onto the structure on each side
and then a strap will hold the engine up.
Right, that is holding the engine upwards now.
All we're going to do is disconnect the engine mount
and then the subframe should be able to come down,
leaving the engine in the car.
What we don't want to happen is the engine come down with the subframe.
Then we're in big trouble.
Now to disconnect the engine from the subframe
which is connected with the engine mounts.
And there's four bolts on the engine mounts on each side.
There's only two engine mounts though.
I'm just squeezing my hand in now to undo those bolts.
And finally, we need to make it clear so the subframe could come down
without damaging any part of the car.
And once we're happy with it,
we're lowering the subframe down and we can unbolt it.
All the bolts are removed from the subframe,
just making sure everything's disconnected from the subframe to the car
and we should be able to lower the subframe down
and we're really hoping that our bar on the top holds the engine
else the engine is going to come out with the subframe which wouldn't be good.
And with all the bolts disconnected from the subframe,
it lowered down onto the jack
and once I was happy with it,
my dad lifted the car up which left the subframe onto the jack.
All of that just because of that.
So all of that had to be removed because of that.
You can see the bad side looks like this and it's supposed to look like that.
Okay, next job.
What I'm going to do, I'm going to take this wing off
because it has, I think, gone backwards
and also it's just going to give us a little bit better access to all this
and then we can see if there's any more damage behind here
because this isn't looking good.
To take the wing off, there's a few bolts under here, a few bolts in there
but we do have to get this part off so we can access the two bolts behind there.
Let's go.
This should also give us a lot better access to the structural damage
that's underneath the wing as well.
First off, the front grille.
Then the headlights around.
This car's coming apart quite easily.
Then all the bolts for the wing on top
and whilst I'm doing that,
Liam's doing the bolts which connect the wing to the front bumper
and that's about everything done at the front there.
We've just got to go inside the wing, remove the washer bottle
and there's two more bolts which hold the wing to the chassis.
Then off it comes.
I can finally remove the washer bottle and the lower half of the wing
and now we can really get an idea of how bad this structural damage actually is.
I'm hoping we can fix it ourselves.
Second hand subframe off eBay.
£679 second hand this was.
I hope it's the same
because Hannah, you've got to swap everything off that onto this one.
Here's the tricky thing about repairing this car.
At the minute, Jaguar Land Rover are undergoing a cyber attack
so we're not able to order any brand new parts from Jaguar Land Rover
so everything we buy for this car has to be second hand
but luckily a lot of the stuff's available.
At the minute, Hannah's transferring over the anti-roll bar
off the old subframe to the new one and also the steering rack as well.
Once that's all been transferred over, we're going to put it back onto the jack,
push it underneath the car and then install it the same way that we removed it
by lowering the car onto the subframe and once it's low enough,
we're going to slide the bolts in to hold it to the chassis
and then all of us tighten it back up.
Once it's secure, the car can go back in the air.
Good news, the subframe is in the car but the engine is still hanging by the straps
so what we're going to do now is make sure the subframe is fully bolted to the chassis of the car
and then also make sure by getting the engine to the subframe,
we've got to connect up this engine mount to the subframe
but that's going to be a bit easier once the subframe is all snug up
then we can make sure all of these plugs are in, back into the steering rack
and everything's connected up under here so I guess let's start doing up the bolts
then we'll worry about this big damage here which I don't think...
You expected, did you Hannah?
No but I think we can do it
Okay so we're just able to get the bolts in for the engine mount to connect it to the subframe
Tight
Once we're happy that's all secure, down comes the car and we can take off the engine brace
Yay! How can you get excited over that?
Now the engine is supported by our new subframe
and the car can go back in the air so we can start our next job
Next step, drive shaft
Three, two, one
We're replacing this drive shaft because there's a split in the boot in the old one
and we don't know how long that boot was split for
so the actual joint could be all worn so we're not taking any risks
and we've got a second hand drive shaft
and Hannah slid it into the differential and now putting the bolt in the wheel hub
After that, the bolts can go in all the lower arms on the left-hand side of the car
Nothing else on this left-hand side was damaged, we think
and even Kevin agrees
Few more bolts in on the lower arms and that's job done on the left
Suspension is back in and all good on this side
So on this side we're gonna not carry on because we've obviously got this
but we can't proceed with that yet
One problem, and it seems to be a common problem on all Defenders
This side light is out, it's got nothing to do with the accident
but we think we've found the solution to it
And the way you have to repair this problem is bizarre
For such a common problem, they made it very difficult to repair
To repair it, we've got to take off this surround
and then we've got to remove the whole headlight
This is absolutely stupid to be fair
because you can't get to the module from the back
and it's not that, that does the headlight
The side light is done by a module in there
so we've got to take off the lens from the plastic
Which means the headlight is going in the oven
Exactly what we got the oven for in the unit
Once we've left it to cook, it comes out of the oven
For some reason Kevin tried to get in the booth
But whilst all the plastic and the glue which holds the headlight together
was nice and soft because it was in the oven
Me and Hannah can start splitting the lens from the backing of the headlight
And there it is
That was actually really good
If you're going to do that, do put it in the oven
130 degrees Celsius for seven minutes
Now it doesn't end there
We've now got to unbolt the front of this headlight
to access the part we need to get to
Out it comes
And there's a plug on the back
We learnt this from watching YouTube
There we go
The LED is there
All it is, is three little LEDs
Which shoot down a little light bar for that side light
And apparently they just burn out
And this is the part that you need to buy to fix it
£25 off eBay
So we're unbolting the old one here
That's the old one
And here's the new one
I assume we just put it back in place and it's all going to work
Gone are the days of just replacing a bulb when your side light goes out
But I guess we're starting to get used to all of this new car jargon
After it's installed, we can reassemble it all
Right, let's test to see if it works
Because all that does is control that one
And this one has a separate module
And that did work, but then it didn't work for bits
So let's see
Excuse you
Before we put the lens back on the headlight
We're going to plug it in and just make sure it works
And...
Good news
Look at that
Yeah, boy
Put side lights, just side lights
Yes
Oh, it moved
Fix it, do you want to come and have a look?
£20 fix at an oven
Well, £25 fix
Look at that
Now we know they work
I'm going to clean up the residue of the glue
That was holding the lens to the backing before
And once I'm happy with that, we can apply our own glue
Then slide the lens back into place and leave it to set
It's vital it's sealed properly
Because we could get water in there if it's not
Then we can slide it back into the car
And reinstall everything the same way we took it out
Here it is, the structure has arrived
We had to buy this second hand
Again, because we can't get anything new from Jaguar Land Rover
So we've got a cut off of a whole car
Which is going to make it very time consuming
But at least we've got probably more parts than what we need
£1,100
Look at that
So this is the mess that we've got at the minute
Now there's some parts of this damage which we're probably not going to touch
Because it would just be purely cosmetic
But the more serious parts, we definitely need to fix
And although this part here that we're changing
Isn't very structural, it just holds the wing on
We need to make sure that it's straight
Or else when we put the wing on, it won't line up correctly with the door
So the first step is to drill out the rivets that are holding this bracket to the car
And for some rivets, Hannah's grinding off the top of them
And then using the chisel just to pop it away from the car
Then we have this damage here
The part I'm most worried about
This middle piece is part of the structure
And it's sort of strengthening that part of the car
And it's all held in with rivets
Because all of this car is aluminium
So whilst I work at getting it off the car
My dad's working at getting it off the piece that we bought
And he's got to be super careful not to damage it
Because we're going to be installing it back onto the Defender
And eventually we got off the damaged part
And luckily there's no damage underneath
So this structural bit in the middle is off here
But I think this has been pushed in
Because you can see where these used to sit from the rivets there
Now to avoid taking out this whole panel
It'll be nice just to be able to pull this panel back
To see where it goes
Really we could do with the new structural part to go in the middle
Then we'll see how far off it is
But for any hope, I just want to see if we actually are able to pull it out
Because this might just be really strong
And we might just be fighting a lost cause
So I'm going to put this in
You can see here clearly how far out this panel is
How's it going Tony?
It's hot work
Hot work?
Hot work, yeah
Are you hot?
Yeah
Now if we're not able to pull this panel back out
We are going to have to replace the whole entire leg
But I think I've got a solution
Called a hustler's bar
Where we had it mounted on something hard like that
And then pulled against it, used all his weight
I think we should probably bring the car back down so we could do it
And then we're going to use a bit of heat to try and pull it
And we're going to use power, heat and power
If this works, it's going to save us so much time
But I was struggling to pull it hard enough to get it back into place
So we called Ethan in for a bit more muscle
Look at it, it's moving loads
And eventually with a bit of heat
The panel did start to go back to the place it originally was
Until we got to a point we were happy with
This is going to be the true test
This is like the structural part
This is the part that we want to get in
All these are all lined up
The rivet holes are all drilled out, ready to go in
But we need to make sure that this fits in its place
Apart from that, it's pretty close up here though, isn't it?
That's good up here
And these bolts line up nicely
We could do with drilling and putting a few rivets in
This whole car is literally held together with these rivets
All of these are rivets
They do look slightly different
Because when you buy a repair set
This is the type of rivet you get to repair it
But these are going to go into the holes
And that is now holding that chassis in
There's a few more to put in
This hole and this hole
But...
It's looking good regarding the chassis leg
Which is going to save us a huge job
As long as this part fits in the gap nicely
Then we can be sure everything lines up as good as it was from me
And lucky for us, it was lining up well
I've now just got to drill out the holes
And then put in the repair rivets
Which hold it to the body of the car
Which is the exact same way it was held in before I took it off
And that is a job well done there
Next up, the bracket on the side which holds the wing on
This just slides into place
And then a few rivets hold it on
Rivets are all in
Time to put the seam sealer over
Some of the joints
Let's go
Time for the seam sealer
This type of repair we would have been really scared of about a year ago
But as we've gained more experience with the type of stuff
We've gained confidence as well
Once the sealer's on
I then applied a bit of paint to it as well
Just to protect it all
And everything lined up great
So then I could move back to some of the more damaged parts
That's out
So you have the steering rack
An inner tie rod
And a track rod end
That's broken
And it should look like this
£21 off eBay
Here is the inner tie rod
We're going to apply a bit of Loctite
That's a lot of Loctite
And then screw it into the steering rack
Which has no signs of it being damaged
After that, the rubber boot goes over it
This slides on
And then we've got one of the special clips which holds it in place
Which Hannah's going to clamp down now
Looking good
Then another clamp which holds the smaller part
After that, we've got to go get the outer tie rod
Yeah!
Mechanic!
Come out!
Yay!
And now Hannah's got to take it off the old inner tie rod
She's just unscrewing it here
And when she's got the outer tie rod off the old inner tie rod
She's going to measure the distance from the end of the inner tie rod
To the locking bolt
Then it will give her a rough idea
Of where the adjustment should be on the new inner tie rod
The car will still need a four-wheel alignment
But at least you can get it close
So it's actually drivable to the four-wheel alignment place
Next thing!
Oh my god, this weighs a ton!
£650
This was
For a full thing
Because I didn't want to take any risk and buy everything separate there
Now, I think the disc is different
And the caliper's definitely different
Because the caliper's way smaller compared to the one that you've got on
You can put the driveshaft in first
Before we put that in
I'll put this in
Driveshaft!
Once the driveshaft's in
I'm going to lift up the whole hub assembly
With all the arms on it
Then Hannah's going to slide in the bolts
Which hold it to the new subframe
And then do the same for the top arm
Time to tighten up all the bolts
Which attach the lower arm to the subframe
Then we can move on to the next job
Shock absorber
We're reusing this one
And hope it's going to be okay
Because these are expensive
The shock absorber, we're going to slide up between the top arm
Then Hannah's going to go to the top of the car
And put on the nuts to hold the shock absorber in place
Then Hannah's going to put in the bolt
Which holds the shock absorber to the lower arm
And finally, the anti-roll bar drop link
Has got to tie into that shock absorber as well
After that, the inner tie rod will connect to the wheel hub
And we're almost assembled
We're now going to be taking off the brake caliper
Which come with that wheel hub
Because the one on Hannah's car was way bigger
And we assumed the brake disc was different as well
So we're taking the brake disc off
Which come with the wheel hub
And putting back on the original one
Which doesn't look damaged
Just a little bit ruster
Once that brake disc's on
Then Hannah can slide on her brake caliper
Which, lucky for us, does fit the second hand wheel hub
Once the brake caliper's on
I can then put in the brake line into the caliper
Right, back in the day on the driveway
I used to be on the brake calipers
And I used to shout to Hannah to pump the brakes
Roll reversal
I'm getting in the car this time
And Hannah is going to bleed the brakes
Let's lower it down, put some brake fluid in
And we're going to have to bleed all four corners
Because there's so much air that's got in there
Let's hope this works
First step, let's add the valvoline brake fluid
We lost a lot of brake fluid when we took the caliper off
So it's going to need a full top up
Then, removing the wheels
On all four corners
The idea of the braking system
Is that you have no air in there
Because air is squishy like that
Trying to get all the air out of the system
Hannah's pouring in brake fluid
But at the minute there will be air in the lines
Because we've had them all off
So whilst I pump the brake pedal
Hannah will go to the rear caliper
Crack open the bleed nipple
And then wait for the air to come out
Until it's only brake fluid
And whilst she does that
I'm going to tell you how you can potentially
Get some money back from a previous car finance
Now did you know 4 in 10 car finance dealers
Between the 6th of April 2007 to November 2024
Could have been missold
Still a bit spongy
But we're getting there
Now the first part of misselling
Was the discretionary commission arrangements
This is where dealers secretly increase the interest rate
To boost their own commission
There was unfairly high commission
This is where commission was excessive
Compared to the loan amount
And there was contractually tied arrangements
This is where dealers claim
They're going to get the best deal for you
But they were actually tied to one lender
Oh look at all that air
Now to get your money back
You can complain directly to your lender
Or go to the financial ombudsman
Or wait for the FCA redress scheme
Which is expected in 2026
Brake pedal feels good
Nice and bled up
Next job is to just do a quick service on it
Because we know how fragile these Land Rover engines are
So Hannah's got the car in the air
And is now removing the sump plug to drain the oil out
Now those options that I just mentioned
About getting your money back
Are all free to do so
But listen to this
When the scheme launches
If you've moved house
Changed contact details
Or your old records have been deleted
It can be hard to go alone
Okay we took the oil strainer out
Replaced it with a tray
So we can get to the oil filter at the top
Because it's at the top
So now Hannah's got to remove in the oil filter
Which is right here
And replacing it with a new one
Now if you didn't fancy going alone
On trying to claim your money back
You can use Reclaim 247
They can trace your car finance history back to 2007
All you need is your name, address and date of birth
It's no win, no free, no paperwork
And it takes less than 60 seconds to start your claim
Your old car finance deal could be hiding compensation
It's your money, claim it back with Reclaim 247
.co.uk
Let's get this service finished up
New oil filter goes into place
And then Hannah can pop back on the cap
And tighten it back up
And you can see the old oil filter
That this car was probably due a service
Next up, Hannah's removing this part of the air intake
So she can access the air filter
But it looks okay to be fair
But nevertheless we bought a service kit
So the new air filter is going in place
That slides into the air box here
Put the intake back down
And then bolt it all back together
So we've done oil filter, air filter
Time to put the sump pump back in and fill up the oil
Back in the air the car goes
And Hannah's got a new sump pump with the service kit that she bought
That goes into the sump
And then she can tighten that up
And we're ready for oil
0w35 litres of Valvoline
Look at that, caramel syrup
In goes the Valvoline oil
And it's always good practice really to service these crash damaged cars when you get them
Because a lot of the time you have no idea of the history of them
Especially this one which has done 60,000 miles
And it says Land Rover, what does that say?
On goes the engine cover
It's not new, I cleaned it
Job done there, time to start it up
Sounds smooth
We did a good job Hannah
You did good, you'll run better now
Right, here we go
This actually could be bargain of the century if we do this
Because this is the old wing
Which does have the dents in it
But we're hoping that the kit from Urban
Which should be on the front as well
Covers that dent and we'll find out in a minute
But let's pop this wing on
And then we can start fitting the rest of the body panels
If we get away with having to replace this wing
Then this could be really good
Because that saves us having to buy a new one and to paint it as well
Alongside that, if we don't have to repair the dent that's in the front of it
It's a win-win situation
Yes
Now we're happy with how the wing lines up
We can bolt it to the front bumper
And start adding back in all the trims which we removed in the first place
Then the front grille goes on
There's an electrical plug for the radar sensor which sits behind the grille
Which is for the adaptive cruise control
I'll plug that in
Then everything literally just clips into the front
And there's a few screws on top holding it in place
Next up, the washer bottles going back in
There's one plug for a level sensor
One for the washer pump for the windscreen
And another washer pump for the headlights
We plug them both in
Slide the washer bottle in place
And then there's two bolts which hold it in
After that, it's this lower piece of the wing
You can see previously they put glue on the clips to hold it in
So if it's good enough for them, it's good enough for us
And I got a little trigger happy with the glue
But we want to make sure that it is nice and secure
Wow, this is never coming off
I'm going to slide it into place
And then we're going to have a bit of tape to hold it down whilst it sets overnight
Job done there
Here is a wide body Urban kit
Which the car already has on
We contacted Urban, we said what's missing out of the kit
They sent us the part that's missing
This front arch
I think it replaces this one
It looks like it clips in to the original clips
I'm just worried about this dent
I don't think we're going to fully cover it
Really should fix the dent
But like what's the point if that's going over the top of it
First, we've got to remove the old trim pieces
Now we're hoping the new trim piece will cover over this dent
Time to see if it will
Yes
So we were going to push out that dent
Am I going to push out that dent?
Probably
No
The clips which hold the old trim piece
We're going to take off and put them on the new one
Right, this is what they use
This is actual panel bond
And this is the panel bond that we got sent with the Urban kit
First, I put on the primer to the wide arch kit
Once I've applied the primer there
I'm going to put a little bit on the wheel arch that we're going to be fitting it to
And afterwards, the panel bond can go in place
And once I'm happy with that
I can begin to fit it
And it actually slides in and fits really nice
Again, to wait for the panel bond to set
I'm going to tape it to the arch
And then Hannah's doing the same on the other side
We have no idea why the car had the rear arches but not the front
These come with the kit, Urban sent them
I would probably put a bit of glue in them
Also, the bonnet vents were missing
But we got these from Urban as well
It looks like these might have popped out in the accident
So to make sure that these ones actually stay in
We're popping a bit of glue on the back of them
And then Hannah's going to tape them in place
Looking good, bonnet vents in, wide arch kit on
Last few bits to go on
Which is under trays and rear arch lining
And we should be able to clear the fault codes and drive out
Next stop, A-pillar
It's missing an A-pillar trim
So we're just going to whack this bad boy in place
That's on
This A-pillar trim come painted gloss black
We just needed to order the bottom trim
And get the body shop to match the paint for us
Time for the car to go back in the air
Hopefully for the last time
And all the under trays can be refitted back on
There's loads of under trays on this
And a lot of them are for protection
Of course, this is an off-road car
So you don't want any big rocks hitting the underneath of the car
And causing any damage
Right, the last thing that needs to go in is the arch lining
But I just wanted to scan it for faults
And we still have, we've got no faults on the car at all
Everything's passed, apart from the ABS
Look, we've got brake hydraulic circuit A leak
And brake hydraulic circuit A leak or seal fault
And when you push the brakes, if you listen
It's pulsating the pedal
Now what I've found, that clicking noise
Is apparently the system checking to see if there's any leaks
And it's confused
I've later found out when we bled the brakes
Like the old school way of pushing on the brake pedal
And then cracking the nipples
Apparently that sends the ABS module into an absolute meltdown
So what we have to do, if we're doing it properly
I've found out that we have to go on to special function
And then exhaust routine
So you have to tell the car you're bleeding the brakes
Else it thinks there's a leak in the brake system
So if it thinks there's a leak in the front right
It cuts brake power going to the front right
So you can use the rest of your brakes
Clever, but also annoying for people like us trying to do it
So if I click OK
So this is what we've got to do
Turn ignition on, ignition is on
Next step, connect the bleeding device to the ABS reservoir
Switch on the bleeding equipment
And set the pressure to over 2 bar but below 3 bar
So we've got to connect Mr Push to the ABS system
Which is in that reservoir, which my dad's got there
And we've got to get 2 bar of pressure going through that
So my dad is pushing Mr Push
Which pumps pressure and brake fluid into the brake reservoir
And we're looking for 2 bars of pressure
At the minute, this fault is causing the ABS light to be on
And the traction control light
Open the bleed screw on the rear left
And bleed the brake system out of the rear left wheel
By pressing in the brake pedal steadily
So it's full stroke and allow it to return to the rest position
So basically all we're doing again is re-bleeding the brakes
But this time with the guide from the diagnostic machine
Deactivate the bleeding equipment that is connected to the ABS reservoir
Deactivate Mr Push
Once we've bled all four corners
We can then remove Mr Push
When numbers 1 to 10 have been completed
Press continue and this will execute a leakage and air monitoring test
Are we ready?
For leakage and air monitoring test
We've got to put back on the cap on the brake reservoir
Then the car's going to perform a test
Sealed!
We're hoping once it performs this test
The brake will no longer pulsate
And we should have no faults on the dash
Test successfully complete
It's been completed and there's no need to complete a repair bleed
So once that was done
Naturally I re-scanned the fault codes
But they still come back
Hydraulic circuit leak A
Hydraulic circuit leak fault seal
But we just did all the tests
So it doesn't seem to work
It says it doesn't detect leaks
But then when we scan the fault codes
It says it's got a leak
We then found online that we should disconnect the battery after this
The battery's under the driver's seat
Which is what I'm doing now
Battery's disconnected
Then we'll just wait
Once the battery is disconnected for two minutes
We've reconnected it
Then we had to do another procedure
So what the guy did on the video
He pressed down his brake pedal for two minutes
Two minutes
Do you want me to start a timer?
Still doing it
The pedal was clicking
And it felt like it was pulsating
But apparently by holding the brake pedal down for two minutes
The computer does a thorough check to make sure
That the braking system doesn't lose any pressure
And if it doesn't lose any pressure
It says to the computer that it's all good
And can go back to normal
Just to check
I'm gonna go back on the brake
No clicker
No clicker clicker
Then he did ignition on
And he did it with the ignition on
Ignition on
Ready?
No clicky clicker
And no ABS light
Just battery low light
Oh my god it could have worked
Why didn't the diagnostic tool say
To take the battery off
And do this clicky clicky thing
Yes!
Look!
No ABS light
No traction control light
And we've got ABS
We've got traction!
Yes!
That was so dumb
What happened to just bleeding brakes normally
Right we need a wheel
There is one on the back
So let's use the one on the back
To go to our favourite place
To go get wheels
To finish this build off for Hannah
Let's go
Whilst I put the arch lining in
Matt and Hannah were getting the spare wheel
Off the back of the car
And once that's off
And the arch lining was in
They can put all the wheels back on
Let's go
Kevin are you ready to try your new dog car?
You like it?
There you go
Let's go then
Off we go
I don't know what your tracking is going to be like
Bye guys
Off we go
Hannah's got the Urus
But wanted something a bit more rugged
That we can throw Kevin in
And shopping in
And everything like that
And this seems like the perfect car
And so far so good
Even Kevin's enjoying it
This was a slightly different project to usual
But it was fun to see Hannah take on the challenge
And it really shows that sometimes
Even if the damage doesn't look too bad
There still could be a lot of work to do
Here we go
She made it
Arrived
Feels like a while since we've been to Wheel Mania
But of course we've come to get wheels
Because Hannah's only got four
You need five on the Defender
I've chose them
But I think Hannah is going to like what I've chose
Let's go in Wheel Mania
Let's get them fitted
And we should see the final product of the Defender
Which literally will be rebuilt in like three days
It's about three days worth of work
Let's go
Right now the Defender's got urban wheels on
And it's missing one off the back
I think these look okay
But it doesn't really have our personal touch on it
Which is why we've come to Wheel Mania to do so
And you can clearly see
They've got plenty of wheels in stock
And I've chose something special for Hannah's Defender
When you buy wheels from Wheel Mania
Normally what I'll do
I will send a picture to Jordan of the car
The registration
Then he'll send me loads of different types of wheels
I can get for it
But if you don't like the type of design
You can even design your own wheels
This time I've chose Vossen wheels
Which are the same on like the Lamborghini Murcielago
Vossen wheels were on Port James' GT3 RS
We use Vossen loads of times
Let's go see the Vossen wheels that I've chose from Wheel Mania
I think they're good
These should finish the build off nicely
I really like them
These are 22 inch Vossen wheels
We've gone for the same size
Just to keep that bigger tyre
And that sort of off-roady look
Now the guys at Wheel Mania are fitting the wheels to the Defender
And it's a bit of an added flex of having the wheel on the back as well
Remember if any of you guys wanted to get some wheels from Wheel Mania
Or wheel refurbishments there
Check out the link I've popped in the description box
It looks good doesn't it
That has made a massive difference
This looks absolutely sick
And in the time that we did it
Was good
It was really good
Now we need to tell you guys how much this thing cost to rebuild
And you need to see the full complete Defender
Let's see it
And this is it
It is complete and done
I think it looks really nice
Are you happy with it?
I'm very happy with it
Was it harder than you thought?
Yeah a lot harder
I've found a new appreciation for the way that you and Tony work
And the cost has come in
You bought the car for £39,000
And all the parts cost less than £3,000 to repair it
Yeah but you do owe me £10,000 labour charge
Because call out boys
On top of that as well
You also got a new registration plate to match the Auris
The HWBT registration plate
Thank you Car Reg for that
Did you not make a profit?
Well if you sell it you'll make a profit yeah
But are you going to sell it?
No never
Yeah I think it's rubbing off
I have two cars
How many do you have?
A bit more than two
Thanks so much for watching the video
If you've enjoyed it hit the subscribe button
Hit that thumbs up button
And I'll see you in the next video
Peace out
