Hi, I'm Mike. Welcome to my Waffle Square, where I obsess about things, and you get to benefit from
it. Well, in episode 13 of our ongoing series, where we are refurbishing this 2006 Land Rover
LR3 with the V8 petrol engine, we're going to be focusing on our tailgate, which is inoperable.
So if you look right under here, you will see something very glaring missing, which is the
actual switch that is supposed to engage the actuator to release this upper tailgate with
the window. Instead, you have to come in from the back seat. You have to grab this cable that's been
exposed by the previous owner and pull on the cable itself to release the upper window half.
Now, thankfully, the bottom half here has a button that is still functioning.
It's obvious that they've been in here to gain access to this cable because
all of these retainer pins here have been broken off, and the two outer
covers of plastic are loose. So we're going to need to get in here to, at a minimum,
re-engage this cable to the actuator. Hopefully, that actuator is functioning. If not, we're going
to have to replace that. But we're going to need to start first with replacing this switch. Now,
I found this one online. I'll show you at the end where to access them if you have the same issue.
Let's take a closer look at it. All right, let's take a look at this replacement part.
So just a simple bubble wrap plastic packaging here. We pull it out, and we have
a nice rubberized new switch. You can see this spot right here that's ribbed upward,
and it's got a kind of a haptic sound. You can hear it clicking. It doesn't click on the outer edges.
I only hear the click dead center. Now, there's a couple wires coming from it,
and then three sets of plugs here. I like that on the back of the switch, it's weather sealed here
with what feels like silicone caulk of some sort. Well, we know this switch is bad just by looking
at it, but did you know there's a way to check the actuator right from the front seat? Let me
show you. Now, on page 38 of the owner's manual, it says if the switch in the back fails to
actuate the upper tailgate release, then you can come right up here to the master unlock and lock
switch, press them both at the same time for three seconds to initiate it. Those are the front,
nothing. So everything up here locked or unlocked, but nothing happened on the tailgate.
All right, let's see if we can figure out what's going on with the actuator in here. Is there a
wiring problem or is the actuator itself so worn out that it won't even attempt to make a noise?
So we've got to get this panel off, and in our case, every bit of it is loose. We just need to
take off these two side straps here. This one over here has been gone through so many times that it's
kind of standing up on its own. It's just sliding right off. If we go over to this one, I just got a
small little screwdriver, and as you can see on this close-up shot, I just pry it up a bit,
and on ours, it pops right off. And then we just gently wind it right back to the plastic trim.
All right, now this is just a dust cover, and if you flip this up, oh, a Georgia peach quarter.
Bonus. You get access to the back here. So everything is loose, but you have to take off
these little round supports to get this plastic piece off. So a half-inch ratchet is doing that.
All right, man, this panel for the lower tailgate has definitely been abused. Every one of the
little Christmas tree retainer clips is broken, and then this side here
has been broken off of it. Looks like we can get this one right here kind of pushed back in,
but the rest are all severed and cracked, so I'm going to have to epoxy this.
So as we can see right here, because all this foam has been torn away, someone's definitely
been in here, and not very gingerly, they really assaulted this thing. And now I know
why the actuator isn't working. You see these two screw holes right here? That's where it
gets bolted to. There's nothing there. It has been removed. Well, all right.
So if we take a closer look at this broken switch, you can actually see
the little micro switch right there, and listen, it's actually functioning. So let's do a test.
All right, I've got the plug where the actuator should be. I've got a couple probes into it set
on DC. Let's hit this little switch. There we go, 12.46. So we will be getting power to this switch
once we purchase an actuator. All right, so nice hardy stamped metal back with a plastic cover.
It comes with the replacement bolts to mount it onto the tailgate, and right here we have the plug.
So it looks like over here we're going to need to remove this plastic cover to be able to get
the cable in there. Let's take it out to the car and do a function test. All right, we've got our
new actuator lined up ready for a test. These two screws here are T15. So let's remove those.
Boom, off it comes. Okay, so here is the actuator, and this spring loaded plunger area should retract
every time it gets the proper voltage. So let's first just test it on its own.
I'm gonna press the button up here on the broken switch. Oh yeah, sweet. Now we're gonna pop in
our cable. Okay, pair of channel locks. There. All right, now right here there is a little
clip, and the little 90 degree bend right here goes through that hole, and that clips into place
a lot easier than that. All right, now let's try it again. Sweet. I'm gonna close the actual catch.
Now let's see if it'll actuate that. Yep, there it goes. It released it. Great. So now let's
disconnect the power cable because we're gonna need to slide this unit in here and bolt it up.
I'm gonna put this cover on first. Now these screws are going into plastic, so there's really
no point in using any Loctite on them. Right, we are ready to loosen up these nuts a bit
and slide these into their spot, and lock them into place, and then put the plug in. But before
we do that, one of Carlo for Hire's favorite segments in any video I do is when I say,
while we're in there, let's do something else. So while we're in here, why not put
some noise-canceling adhesive foam inside this panel. I'm hoping not to be in here
anytime soon again. Now they put a really good job over here of putting a piece, I can feel it,
of like Kilmat over here that keeps this from getting that resounding boi-oi-oing sound, but
we can do a little bit more over on this side to deaden the sound everywhere we can reach through
here. So I am going to take my rag and this rubbing alcohol, let's get in there,
degrease that area, and put this adhesive back sound deadener in. Yeah, a good amount of dirt
was in there, huh? Now I'm just going to peel back a small bit so I don't inadvertently get
stuck on something, and I can pull the rest out once I've got it into my preferred spot.
Just like that. And now I pull the backing off and rub it in there,
and we've got room for one more piece like right up in here. Next we're ready to ease this guy
into place, and look at that. Just fits right into these little slots. Boom, look at that.
I love it. These two are 10 millimeter bolts, so let's... I'm going to cinch one down
just to hold it in place, and then I'm going to take them out and put a thread lock on each one.
All right, I'm going to use blue Loctite so that if we ever need to change this out again,
it won't be that hard, but it's not going to come loose during all the vibration of driving.
Cool. And number two. Okay, now I'm going to reach in this slot here and put the plug in.
It only goes one way. There's little notches right here that make it so you can't put it in wrong.
All right, let's listen. Yeah, that's working. Now let's do the real test. All right,
let's reach under here and get that micro switch. There it goes.
I've got this little support down here until we put those two straps back on. All right,
so this repair is done. Now I want to put some more foam back over this like it was
from the original manufacturer, but before I do that, I want to clean this whole tailgate area.
If I lift this cover up, you can see there is dust and glitter in here. I don't know what happened
with the previous owners, but it's like a glitter bomb went off in this car. I find it everywhere,
and I'm in the process of cleaning it all up, so if I ever find any heavy deposits of glitter,
I'll know Aspen's up to no good. Let's clean that up though. All right, quick rub down with
rubbing alcohol so I can get some more of that Noiko soundproofing down here. I'm going to use
the same stuff to cover this. Now I'm going to avoid getting any of the sound deadener
in these three spots because the panel clips are going to go in there, and I don't want to
fight through this stuff. I don't know if that's any quieter, but it makes me happy.
All right, lastly, I'm just going to clean up everything around here before we put the panel on,
and then let's go head over and repair that broken piece of the panel. All right,
I've cleaned both surfaces off with rubbing alcohol. Now let's take this epoxy here. I'm
using JB Weld. It's a two-part epoxy, so we're going to mix this together really quick,
and it sets in five minutes, so it is a mix and go. All right, let's get some spring clamps on here.
Nice, and we'll let that set up. Now before we put this on, we're going to need to take off
this trim piece here because this guy won't slide in and then engage
all of our little panel clips. They have to go straight down, so unfortunately, we need to
remove these four Phillips screws, each one covered by a little plastic bun. So I'm just
going to pry those off with a multi-tool here, just like this, and we have the same panel clips
underneath that we need to pop up. I'm just being very gentle with them. There are two of those,
and these still look in good shape, so we can reuse them. Also, while we're in here,
let's give it a little shot of silicone lubricant. Okay, now we can lower this back down
and prepare our panel to go back on. Now, I've got new panel clips here. I tried the green ones.
The green ones do not fit. They're not quite long enough, even though you can barely tell
the difference. I will leave a link, however, to these, but let's get them in place. All right,
now we can line these up. Nice. Now put our little connectors back on for the cables.
Now we'll line up the panel clips on our trim piece, one, two, and put in our screws,
and finally our buns, one, two, and four. Nice. So now it's time to replace this broken switch,
and you could just get in here, try to pry it out, and then splice the wiring. I haven't seen
a single video on actually getting this thing out in one piece with the whole wiring harness,
so I want to do that just to see how difficult it is, and I also tried getting in here to pry
out this piece. There's a couple clips on the sides, and I haven't had any luck, and I don't
want to break this piece of trim, so I'm going to do it the hard way, get in here, and start taking
off the inner plastic molding. So since we need to get behind this rubber weatherstripping and
I don't want to damage it, I'm just going to remove it. It's got little integral clips.
Next, I'll remove the Phillips screw from the handle here, and now the regular panel clips.
Just by removing the rubber weatherstripping and this side of the panel, it exposes the plug
to the switch. Three 12 millimeter nuts that are holding this unit on, and then there are four
T30 bolts right here. Let's remove all that, see if we can get this unit off,
and disconnect the switch right here. In addition to all that, there's also two plastic panel clips
in there. So I disconnected the switch cable, and let's remove this. Here we go. And because
nothing can ever be simple, the replacement switch has a different plug. That was something I saw in
some of the comments on Amazon, and it looks like it stands true. So in light of that, I think the
easiest thing to do is cut the wires to the switch itself and splice those together. I had considered
switching the components in here over, but this little metal piece right here is missing inside
of this broken switch, and it just wouldn't work. So I'm going to replace the whole thing.
Now these are the clips on the side that I was talking about, and I cannot get in there, even
through here, with bending a tool and overcome these clips. So I think what I'm going to do
is take a drill, drill in here to take care of this side of the clip, and then we can get to splicing.
You saw it here first. That is a complete pain to remove. All right. Strip, flux, solder, heat shield.
Well, putting this back together is really just a reversal of the process I already showed you,
so I didn't waste your time in filming it and putting it in this video. But if you want to
play it backwards, yep, nip, nip, nop, Freddy is the devil, you can see exactly how to put this
back on. But what a difference in functionality. We went from having to climb through the back seats
to a fully functioning tailgate as good as the day it rolled off the showroom floor. I am so
excited to bring you this video. I couldn't find anything else like it online, so if you found it
helpful, will you please give it a thumbs up? It really helps the channel. Also, please consider
subscribing. It's free. You just have to log in and then click subscribe. I'm going to leave links
for everything that I utilized in this video, including these awesome panel clip pliers. They
can get into really tight spots and safely pop those panel clips. I used it to get in here.
Those are going to be Amazon affiliate links, so if you click on them and end up making a purchase,
it won't cost you a thing, but I do get a small reward at the end of the month. It helps to
justify all the time it takes to make these videos. Speaking of these videos, I'm hoping the
next one is going to be replacing the leather on the two front seats. That's going to depend
on the supplier, but they need it. They're in bad shape, and I'm hoping that's going to be
the next video. Until then, thank you for watching. What do you think? It's so nice.