Rawhide edging on Heater Shield: What you need.

Shield of Antiquity
8 followers
2 Video Views·Jan 16, 2026
Coach Nate shows the tools you need and how to use them to get your Heater Shield lined with rawhide the easiest way possible.
You will need:
1.Leather Punch set with punch pad.
2.Nail punch.
3.Drill bit/ drill ( large enough to make hole for large size needle.
4.Tapestry needle 2x
5.Leather belt scrap for matrix.
6.Taylor's measuring tape.
7.Hammer.
8.Two inch wide rawhide strips.
9.Fabric cutting board
10.Sharp knife.
11.Synthetic sinew.
12.Water.
Hey YouTube, this is Coach Nate McBride with the Blade Fit Academy and today what I'm going to do
is show you the tools that you're going to need to put rawhide to line your heater shield. Okay,
so a couple of things that we need right from the get-go. You're going to need some rawhide.
I'll explain how to prep the rawhide in a different video, but you're going to need
some rawhide and you want two, you want it to be at least two inches wide. Okay,
so you're going to need some rawhide. Second thing, you are going to need Taylor's measuring
tape. You're going to need some kind of wire. I don't think that sewing, well don't use fishing
line. I did that first. It is just hell. Don't use fishing line. This is artificial sinew.
This, after trying to not use this, you definitely want to use this because whatever money you save
on twine or anything like that, you're definitely going to make up on time in using this artificial
sinew. So artificial sinew. You're going to need this little guy. This is something that you get
at the hardware store. This you put up against the little nails that hold in the baseboards.
You tap in the nail so it goes deeper into the wood and then you come back and then you put the
wood putty and paint it over so it looks like there's no nails in it for your crown molding
and then for your toe kicks. Not your toe kicks. It's molding on the floor, whatever the heck that
stuff's called. This, you need this or something like it. Something to where when you nail down
it makes like a little dimple or a punch in your shield and also in your rawhide.
I'll explain how that works in a bit because you also need, honest to goodness, a hole punch.
I got a hole punch set. This is the Odin six-piece hollow punch set and trust me,
you definitely want something like this. Not only to punch the proper size holes in your rawhide,
see like here. I'm not sure if that it shows up so well, but yeah, you want that. That's from
this punch here. This just gets it started so you know where to punch it with this. This
gets started and this punches in the rawhide. In the wood, you put this and punch it in the wood
and then you get a drill bit and you finish the job of the drill bit. The diameter of the bit
is highly dependent on the next item which is these. This is a sewing needle. You're actually
going to need two for this project. These aren't just regular sewing needles. These are called
tapestry needles and a tapestry needle is not sharp on the end. So believe me, you're not going
through, everything's already punched. You don't need it sharp on that end and it is just so much
nicer to not have to worry about pricking your fingers when you're going through. The reason
why you need two of them is because you attach one on this end and the other on the other end
of your string, right, of your synthetic sinew and it's the way that you sew it and I'll show
that in another video, but you're going to need two tapestry needles, okay. Do yourself a favor,
get tapestry needles. I found that out the hard way. What else do they need, Nate? You're going
to need a hammer, right. You're going to need a backing. This backing is for this. You put the
rawhide on there. Use this as a backstop and then for the hole punch, you don't want to use,
for the hole punch, you want this. This happened to come with this kit. You don't want to use this
on this. It'll actually go all the way through if you're not careful. So I have this guy,
just a piece of wood somewhere, something you don't care about putting holes in for this,
okay. Rawhide, what else? Drill, okay. You need a sharp knife, okay. This is just a box cutter,
but you want to use a fresh blade when you're cutting the rawhide, all right, because you're
going to size up the rawhide that you need with this. That's what this is for.
And I already know the measurements of this shield, but in case you don't, you measure,
right, and this happens to be 21 inches this way. You want to measure it on the curve, okay,
21 inches, and this is 32 inches. You want to measure along the curve, all right. So what I'm
going to need for this, right, I'm going to need rawhide. I'm going to need three pieces.
This one I need 21 inches long, and from here to here is 32 inches, and from here to here is 32
inches, but what I want to do is I want to cut a separate little end because wherever I connect
the two, wherever I butter up the, down here, the rawhide pieces, I want to shore it up with
another little piece. So one of these, I want to actually go over this edge and back down here,
and then the other piece I'm going to have here, I'm going to have this little butt in the middle,
the line, the junction, and then I'm going to get that little piece, right, and I'm going to make
sure the holes are in the proper spot to match the holes in the shield, and I'm going to sew that up,
and it's going to look so sweet, really, really nice. Anyway, guys, that's just a quick intro.
The next video, I'm actually going to work on it and show you that. I just wanted to get this out
so you guys can see the method behind the Manus. Do not skip on the tooling. I have tried to be
smarter than everyone else. Do not try and be smarter than everyone else. These are the basic
things that you need. Preparing your rawhide, gosh, I mean, on the internet you can find these
just like this, and then you can cut the lengths, but that's actually more expensive. If you're going
to be doing a lot of these, say you have a club that you're working on and you just want to make this,
what you're going to want is a sewing, a cutting board like this, a backboard. It's used for,
you know, you put the material, your material on there, and this is inches because we're in the U.S.,
right? So it runs along here and here. Then we've got this top thing that you lay on there just so
you can keep a straight line, and then you make your cut. So rawhide comes in what's called bends,
and I get mine from Tandy Leather, and when it comes in, it's rawhide. You want to chuck that in
some water. You want to get it wet, okay? Prep it. Believe me, do not try and cut rawhide when it's
rawhide. You want to just throw in the water for half an hour, 45 minutes, and it gets very pliable.
This is starting to dry up again, but it gets pliable. You lay it out on something like this,
and then you can measure out what you want. You want this at least two inches, guys. Believe me.
You know what I forgot? One piece of tooling that you need, and this is a great time to explain what
that is. You need to make yourself some kind of a matrix here, okay? There's three holes, but we're
only going to worry about the first two. The two, not these two that are close together, but this one
and this one, okay? That's an inch and a half away from each other, okay? The reason why I made this
is because this is the matrix for being able to line up the holes that I punch in the rawhide
and the holes that I drill in the shield. You want those to line up as close as possible,
and this is how you do it, okay? You pre-measure what you want, you make that, and it needs to be,
and here's why I say that the rawhide needs to be two inches, right? Because I have marked
the bottom edge here is the edge that is going to go when I fold this rawhide in half long ways,
okay? I'm going to stick this in here, and I'm going to line it up. I'm going to take this punch,
the first punch. I'm going to put it here behind my backing, not on the shield, but put it on the
backing like this, okay? I'm going to make sure this is the ends meet on the rawhide long ways.
I'm going to find this first hole, and I'm going to punch it, boom, like this, and I'm going to
go throughout all this rawhide and punch the inch and a half holes, right? Then I'm going to lay it
down flat, then I'm going to get this guy. I'm going to put it down here, then I'm going to get
my proper hole punch, and wherever those little teeny holes are, I'm going to get right in the
middle, and I'm going to punch those holes, okay, right? And then at that point, the holes that,
well, and you're going to use this same thing, right? After you've put in the rope, I'm going
to put rope around here, glue rope on, and then I'm going to take this, the bottom edge, I'm going
to line up against the rope as the edge, and then I'm going to poke my holes, boom, same way,
boom, on my shield, okay? And I'm going to line this up like so, okay? And then I'm going to make the
new one, boom, and I'm going to line this up with the last one that I did, and then I'm going to
find the new one, boom, again, line it up on the last hole I did, find the new one, boom, and then
I'll have dimples along my shield, then I come along with my drill, drill, drill, drill, drill, drill.
Now, these holes are the exact same spacing as my rawhide, and then I take my, my needle, okay,
tie the needle on your thread on both ends, okay? One needle here, one needle here. I'm going to put
this all the way to where my line is, is halfway through, and I'm going to, I'm going to thread
this through the next hole, I'm going to take this and come from below, thread that through, then I'm
going to take this from above, thread it on the next hole, and this one that's below now, thread it
through, okay? So, these are going to go opposite to each other, okay? It's the thatch weave if, if you
follow World War II fighter pilot tactics, okay? They're both weaving like this all the way through,
when you get to the end, cut it, tie it off, boom, move on to the next one. Anyway, that's the parts list,
guys. This is definitely what you need to do it right and to make it look really good. I'm Nate
with the Blade Fit Academy. Always remember to slay your demons, and I'll catch you next time. See ya!
