Fitted Shield Cover Tutorial

Shielded Dynasty Network
2 followers
2 Video Views·Feb 21, 2026
Hello and welcome to the Akia Magna Fitted Shield Cover Tutorial.
Second to constructing their first pair of swords or so, the shield is the second piece
of equipment a new player will want to build.
After you've put the foam and handle together comes the cover.
While there are many valid ways to cover your shield, you'll find that an old t-shirt duct
taped over your shield isn't quite good enough for obvious reasons.
So what I've prepared for this video is a common way to cover a shield.
Preparation First we'll go over the list of materials
you'll need to build your shield cover.
Your first shield cover doesn't need to be made out of a high quality material, but I
recommend at least a heavy broadcloth because your shield will be getting hit a lot and
you don't want it falling apart.
You're also going to need thread to sew it together.
Try to get a matching color if you can.
You're also going to need to know how to use a sewing machine or hand sew.
This tutorial does not cover how to sew, but if you have the basics you should be able
to get by.
As for your measuring and cutting devices, I'm using an L-shaped ruler, a pair of scissors,
and for tracing I use a non-wax colored pencil that has a half inch of foam taped to the
side of it.
This is so that it's easier to measure out the seam length.
Finally you're going to need some stringing material.
I use this fishing line, but any kind of string that's long enough will work.
Measuring The simplest way to measure out the face of
your shield cover is to trace it while adding a half inch for seam allowance.
Fun tip, if your material isn't enough to cover the shield, sewing two or more pieces
together can give you more room and add some flavor.
For the edge you want to measure out the thickness of the shield and then add about three to
five inches.
This amount can be more depending on the thickness of the shield and how secure the cover needs
to be to the shield.
The general rule is that the thicker the shield is, the more onto the back of the shield the
edge material will need to go.
After you've done all your tracing, go ahead and cut the material.
Sewing Starting with your edge material, fold the
last inch to inch and a half along the inside of the outermost edge and sew it down.
Make sure you leave the holes at the edges unsewn so that you can feed the string through
later.
If you're having trouble, sewing pins would help here.
I don't do that because it was how I was taught when I learned how to sew.
Depending on how long the edge of the shield is, you may need to sew multiple edge links
together before sewing the fold down.
Next sew the edge to the shield cover face.
At this point it's important to make sure you're sewing on what will end up the inside
of the shield cover.
Again, sewing pins might help you here.
Threading the String Attach the string to something hard and
easy to manipulate under the fabric and feed it through the hole.
In this example, I'm using a recycled piece from a pen.
Remember not to cut the string until you've finished feeding it through.
After you've finished feeding it through, attach it to the shield and tie it down.
Now you should be able to cut off the string without worrying about the string sliding
into the shield material.
At this point, you can tie it down like I did, or you can use a drawstring clip.
I don't like drawstring clips, personally, because I don't trust them to stay on.
And there you have it, the fitted shield cover.
If your shield is small enough and perfectly round, you can skip the step of measuring,
cutting, and sewing the edge material and just make a really big drawstring bag.
It's basically the same.
This isn't the only way to cover a shield, and I will link other relevant tutorials in
the description.
If you have any questions, leave them in the comments and I'll promise to try and read them.
Thank you for watching.
If you like this video, please rate and subscribe.
Until next time, I'll see you nerds later.
