Crye Precision: LVS Patrol Cut Base and Tactical Cover

Ballistic Lab
1 follower
1 Video View·Jan 11, 2026
Crye Precision: LVS Patrol Cut Base and Tactical Cover
Hey guys, tonight I've got a video that's been kind of a long time coming.
Never heard anything bad about this, but also never heard much of any real value, I guess
is the easiest way to say it.
So we got the Cry LVS with the tactical cover, I think that's what it's called, we'll check.
A lot of the value of this thing, I'll be completely honest, is there's no way to show
it in video.
And that's really the base armor and how comfortable it is, which I had heard good things about
and they were all very, very true.
This is incredibly comfortable, but I'll go through the features on this particular cover
and then I'll show you the base LVS, hopefully in better detail than you've seen elsewhere.
Everything that I found leading up to this was like shot show type footage, so very,
very minimal content.
So hopefully you'll learn a little bit more about it.
If not, take it as another testimony that it's incredibly comfortable and a very well
thought out system.
So we'll get it on the table and go through it as detailed as we can.
We'll start with it in the cover.
It's not the quickest process to put in there, but I'll show you what it involves to install
it into the cover and then we'll look at the base model by itself.
So stay tuned.
Okay guys, as we go through the LVS and the cover and everything, bear with me a little
bit.
There's a good chance that at some point in time I'm going to get something off camera
that I don't intend to, and I'll do my best to pay attention to that and fix it as we
go.
All right, so like I said in the intro, this is the tactical cover.
There's I think four or five covers available for the LVS, none of which are required if
you just want soft armor.
All right, there's an overt, I think is what they call it, that has like three mags up
front and then it's relatively slick beyond that.
So it's kind of a misnomer in my opinion that they call that the overt, but whatever.
It's neither here nor there.
So again, tactical cover, we've got medium LVS, medium tactical cover.
I think I have the standard cut soft armor.
I'll know for sure once we get inside there.
So there's two cuts of the actual LVS itself.
I don't know how well the other one plays with the covers, so I apologize for that.
I made sure to get the standard, I think, which wasn't the more highly recommended one
because I wanted it to play with the covers.
My needs for conceivable soft armor are pretty minimal, so I wanted it to work with the rest
of the system, if you will.
So looking at the front plate bag here, this is a very, very intricately put together assembly
when you look at the whole thing.
So the cover itself, I want to say is right around $300, maybe $350, which is pretty steep.
And then the LVS base, which includes soft armor, full cut soft armor obviously, is a
good bit more expensive.
I think it's right around $700, $800 street value.
I did get mine used, but it was mint, so it was still pretty close to MSRP.
I really bit the bullet to bring this one to you guys.
I paid out of pocket for all that.
But I had heard great things and was willing to take that chance.
So looking at the front plate bag, as well as this thing is put together, it does lack
some features that Crye has on their docket.
So I'm a little disappointed in that.
There's no admin pouch on here.
You've got straight MOLLE, two rows, four columns with Velcro on top, and then Velcro
staggered so you've got plenty of room for ID placards or whatever.
And then there are some vertical loops here, which you could mount side release buckles
to if you wanted to.
There's really not a good reason to because it takes the AVS panels just fine.
So I would probably reserve those for push-to-tuck mounting if that was something that you need.
The cummerbund, we don't really need to talk about too much because it's a straight up
AVS cummerbund.
So when you buy the covers, if they need a cummerbund, they will ship with the math kind
of already done for you.
So this is like a large, extra large AVS cummerbund, even though it's on a medium vest because
it has to go around soft armor wings and they accounted for the sizing differences.
So with that said, if you're on the larger size of whatever base you're buying and you
know that you want to have internal radios and potentially hard side plates, you may
need to be realistic about the size of your cummerbund.
So just keep that in mind.
You don't need to step up anything or play any games if everything is normal.
But again, if you're on the larger side, you may need yet bigger cummerbund, which you
might have to go custom to get.
So we'll get the cummerbund out of the way as far as the front goes.
Okay, so you've got your traditional AVS mounting here and you've got the little kangaroo pocket
there that the tuck tabs go into.
It's gonna be a little difficult to open that up right now with the plates.
So we'll leave it.
It's there.
It's the same as your AVS or your JPC2.
So any kind of weird gimmicks that you guys have going on for that, you can still do with
this.
Like if you want a center mounted super thin knife like the Benchmade deal, you can probably
fit that in there behind your AVS panel and still mount it correctly.
Looking off the sides of the front plate bag, and this is also on the rear plate bag, you
have a built-in magazine pouch with this Velcro and shock cord retention.
So we'll tuck that away real quick and I'm gonna show you how magazines fit.
It is a stretch pocket, so PMAGs fit without any issue.
Obviously steel mags fit just fine.
I think I got 152 here handy.
I can't remember if these fit.
Yeah, so you can fit internal radios without any concern.
So your commercial Motorola's are fit, your cop radios, 152s, 148s, I probably wouldn't
go MPU5 in here just because it's too much stuff too close to your face.
The radios don't sit very low.
It's not like the AirLite where you can lower the bottom of the pouch.
So 152 is about as uncomfortable as I would want to be in here.
Cop radios are probably going to be a little bit better.
Your APXs and your Harris's and your Motorola's or whatever, they tend to be a little bit
shorter than a 152.
So they fit all right.
Okay, so you've got that on each side and then you have a similarly sized one on the
back.
We'll verify sizing on that just in case it's slightly different.
It is tweave with a Cordera backer on there and then the shock cord with Velcro tab loop.
You may need to get some longer shock cord to go over your radios if you still want good
Velcro continuity there, but that's really not an issue to be concerned about.
Shock cord is dirt cheap and I wouldn't steer you away just because you don't have enough
shock cord.
All right, looking at the shoulder straps, we'll try to pay this out as best as I can
here so that you guys can see it.
We've got a lot of Velcro overlap here, so you've got this strap that runs from the front
plate bag through the Crye ladder lock there, the metal one, and then back over on itself.
This whole under assembly here is coming from the rear plate bag.
You are kind of stuck with that, but with that in mind, you can tweak your shoulder
strap here if we undo this Velcro.
You could bring this rear bag all the way up to here.
If you guys know, I like to have my shoulder straps pretty tight to get the armor up correctly.
If I've got this much leftover room, you could be a pretty small dude and still get your
plates up high enough.
Additionally, looking at the side of the plate bag here, you can see just how much assembly
goes into this.
There's stretch panels on the side for the hard plate pocket and then the rear plate
pocket behind it with the soft armor is sewn in there too.
There's a lot of intricate work that goes into putting this together and making everything
line up correctly.
You've got front plate pocket Cordura, stretch panel, rear plate pocket Cordura, stretch
panel going into that, and then the whole shoulder strap assembly fitting in together.
There are a lot of pieces that all meet up around here and it's very cleanly done.
This is definitely the quality and the design that you would expect coming out of Crye.
Your shoulder straps are lined with Velcro, so if you've got bicep armor or something
coming off of there, that'll work just fine.
There's Velcro inside the neck area of the front and back plate bag, which will help
tie into some neck armor.
You can piecemeal this thing all the way up to full-blown assault armor if that's something
that you need to do, whether your department dictates it or whatnot.
There's webbing tabs coming off the shoulder strap area.
They're just kind of fixed in place there, so it tie-downs for other things.
I don't know if any of the pack systems tie into this.
I don't necessarily think that they would, but they're there if you need them.
That might be for some auxiliary armor, maybe some secondary tie-down to keep it from flying
off on you.
Alright, we'll look at the internal of this plate bag real quick.
So again, when I'm talking about how well-constructed and how well everything fits together, you've
got some very nice spacer mesh in here, some more stretch panels, the Velcro work up here
for the add-on armor, and then all of that meets very cleanly at the top of this, which
contains your LVS base.
Look at the rear plate bag real quick, and then I'll kind of show you how the armor goes in.
So rear plate bag, like I said, you've got the Crye metal ladder-lock type setup there,
the two-piece setup.
You've probably seen that before on, I believe it's on the AVS.
If not the AVS, it's on some of the First Spear sleeper and sloucher rigs.
Kind of interesting how the Crye buckles make their way around the place.
Alright, you've got a drag handle here.
I don't know how far down this webbing extends.
It's kind of tough to tell because there's MOLLE and Velcro and lots of layers going
on there.
You've got two more tabs here.
That could potentially help you tie into a pack system a little bit more realistically
than the ones on the front, but it might also just be for armor tie-ins.
I don't remember if that was in the manual or not, so I apologize.
The rear plate bag is set up very similar to the front with the stretch panels on the
side there and then the soft armor portion sewn internal of that.
So again, this is kind of why they ship with such a large cummerbund.
So you've got soft armor and then a sappy plate and then cummerbund on top of all of
that.
So it does eat up some of the length of the cummerbund.
And you can see mine without anything internal, I got it pretty snug.
It fits your, I've got it tied off right in the middle there.
And I apologize, earlier I said it was a large XL, it's actually 2X for this setup.
So that is what it shipped with.
I don't think I'm quite that fat, I wouldn't have thought to get a 2X cummerbund.
You can see your rear pockets here, we'll just verify again with the big radio and make
sure that still fits.
Can't remember if these are a little bit smaller than the front ones, they might be.
This isn't playing along quite as well as the front.
So I think these are actually a little bit smaller, that's not to say that we can't get
it in there.
Alright, so the radio fits, so that's cool.
Much more difficult to get in there, but it does fit.
It's not overly stretched in my opinion, nothing looks overly taut there.
If you had a smaller radio, it would go in there easy peasy.
Harris is a pretty tight fit.
But that makes a little bit more sense to me to have a radio back there than another
magazine.
So I don't know if there was a reason behind the difference in size or if that's just kind
of how things worked out.
Alright, the cummerbund laces in just like any other Cry rig that you've had before.
It is kind of interesting though, so you've got your horizontal molly here, and then you've
got these vertical strips.
So the cummerbund, because there's not really a channel for it, and I don't know how well
this is going to show up because it's multi-cam on multi-cam on multi-cam.
But there's vertical webbing, four strips of it here, that your cummerbund slides into
and it actually rides between the horizontal molly, just like it does on any other Cry
vest.
But there's no zip-on panel here.
So that's how that works.
Additionally, I don't know if I noticed this before or not, there's a pass-through here,
which we'll explore in a little bit more detail, but it looks like you could get away with
a Velcro on Velcro cummerbund in there too, if that's something that you wanted.
So let's get the rear plate out of here and see if that opens up a little bit more.
So the nice thing here, the plate bags are all externally accessed, so you could still
have danglers on there if you want to.
It would be external of your soft armor, but it would still be internal of the hard plate.
We'll get that armor out of the way there, and we'll show you kind of how the plate bag's
set up.
So you've got your internal strap to help fix your ride height, if you have any issues
with ride height, and then your Velcro flap to close that.
So that's going to be loop on the body side, hook on the outer portion for your dangler
compatibility, and then let's see if we can get this pass-through open here.
All right, so looking in that pass-through, it does go all the way through.
It's going to have hook on the outer portion and then just a thin line of loop internal
to help close that up.
So you could put whatever cummerbund through there that you wanted to, and in all reality,
I could have put the kind of skeletonized cummerbund through there if that was something
that I wanted to do to kind of help clean up this area a little bit.
There's no zippers on here, which is a little odd in my opinion, just because this is like
the premium cover for the LVS, and Cryo has zippers on everything else these days.
So it is a little interesting.
I'm not really sure what drove that decision, but there's always workarounds with that with
zipper adapters and whatnot.
And maybe they just felt somebody would want...if they wanted anything on the back here, they'd
molly it on.
I'm not really sure.
We'll get the front plates out of here too, just to lighten this up a little bit.
You do have your snap in there for your AVS panels, and then some webbing down here, which
I would assume is for hanging a groin panel off of.
And we got plate two out of there.
The front plate bag does not have that internal strap, kind of an interesting difference,
but it's still closed with the same orientation of Velcro.
And if you caught it, sappy plates fit in here pretty darn well.
It's probably one of the better sappy fitments on the Cryo stuff.
Usually, you got to struggle a little bit to get the Velcro lined up.
Really not too many issues with this one on the sappy plates, all right?
Okay, so now we've got our hard armor out of here.
I think we covered everything on the carrier itself, or the outer shell, the cover, if
you will.
I don't think there's anything else really left over.
Shoulder straps, I understand there's a little bit of stuff going on there, but it's Velcro
and then front strap routed through the back, all right?
I just don't want to miss anything on here for you guys.
I talked about side pockets, really nothing else going on here.
There's a little bit of capability for cable routing, if you want.
So that's a clean pass through there.
Not really intentional, it's just to kind of fit the top corners of the plates and everything
and keep the designers sane, I think, so it's not any harder to sew together, all right?
So we will open this up now.
So there's a zipper on the bottom of the soft armor portion, and you can see the zipper
tab tucks in real nicely there, so let's see if I can even work that out under pressure
here.
All right, so we got the zipper out, you can see the zipper pull tucks into its little
pocket there, and then we open that up.
If you've never had a full cut soft armor before, zippers are pretty common on the bottom
of these.
You do run the risk, a little bit, of eventually blowing out your zipper and then it's not
easily fixed.
So do be careful when you're zipping things in there to make sure that you're not grabbing
your armor or doing something else that's going to blow out that zipper prematurely.
That said, this armor's incredibly light, so it's not bearing a lot of weight, and with
the plates, the hard plates external, it's pretty minimal effort on that zipper, all
right?
So you can see we've got the LVS base shoved in here.
The shoulder straps just kind of do what they want inside of there.
So I tried my best to hide at least one of the hook portions in there so that it wasn't
sitting on that 3D mesh, but there is a little bit of concern that you could eventually rub
that a little bit with the hook from the shoulder straps.
All right, so we'll get the LVS out of here, the actual LVS, all right?
It's not hard to install, but you do need to take your time with it just a little bit
to get it in there because it is a skin-tight fit.
All right, so we've got the front of the LVS pulled out.
We'll get the back now.
Same thing, we've got the zipper here.
Got to work that free, unzip it.
I remembered it being a little bit more difficult to get these in here.
It takes a little bit of effort to line up the wings and everything, but at least removing
it under pressure is going all right, so pull that out.
Sometimes these soft armor panels will have Velcro on them to help engage with the top
of the covers, but with the LVS being its own vest, it's got a little bit more strength
to it, so you don't need that Velcro to help keep the top from folding over.
All right, so there's the back panel, so I'm going to set this aside here.
We'll get the plate bags out of the way, and then we'll take a look at the LVS itself,
all right?
Okay, so now the tactical cover's out of the way, and we've got the LVS base vest.
So this is the patrol cut, all right?
So I might have misspoke earlier, and I might actually have the more highly recommended
one, and it still fits fine.
I'll have to double check on that one, but if anybody knows different, call me out for
sure, and I will make a note, all right?
So when you buy the LVS, this is what you get.
You also get the exoskeleton kind of looking frame for it, so you can store it without
putting any real attention anywhere on here and potentially folding over your armor.
It's a nice touch.
Let me grab it real quick for you guys.
So here's the shell for it.
It's a nice touch, nice thought, but it's kind of unruly if you don't need it.
So you can see it's got that curve in there to help keep the wings of the armor curved
around your torso-type shape.
So this band keeps tension on that and keeps it curved.
And then you've got this webbing strap here that keeps the armor itself in the frame.
And then you've got a hanger, so you can hang it up in your locker.
All right, so like I said, nice touch, but it's pretty unruly to store anywhere.
All right, so with that out of the way, we've got the front of our armor here, we've got
the back of our armor.
And the big selling point of this thing that is not easy to understand, at least it wasn't
for me when it was released, is there is no outer portion of the carrier.
So this is your armor in its little protective wrap that you would have on any soft armor,
right?
You're not going to have your bare Kevlar or whatever whiz-bang material they're using
these days exposed to the elements, but they took it an extra step.
They made the wrap, kind of the finishing shell on this thing, and they put the shoulder
straps right in there, as well as your torso wrap, right?
It's all there, all right?
So when we put this thing together, we just line up our shoulder straps here, and they're
kind of an interesting assembly.
So you've got loop towards your back, and then hook towards the front, and then on your
front panel, you've got this little piece of hook here to engage that loop, and then
a bunch of loop.
I'm not quite sure why it's set up that way, but that's how it is, all right?
Your shoulder straps are very minimal, because this thing is designed to be worn as concealment
armor.
So they're very thin, they've got a nice width to them.
A potential issue, if you're a real small dude, that you've got kind of a good bit of
shoulder strap there, but very comfortable and not an issue in width, at least on my
size body, all right?
And then you've got your elastic cummerbund here, which can be removed.
This is a cummerbund pass-through on the back.
It's a little unruly, so I definitely recommend having some cardboard or something to help
install the cummerbund.
Like I can tell over here, I kind of messed something up somewhere in here.
But you have two options for cummerbunds.
You've got this four-inch cummerbund, or you can put two two-inch cummerbunds on there,
all right?
So you have the same width of the cummerbund, however you do that.
Just one piece or two piece.
I went with the one piece just because, I don't know, I'm having, I think, nerve issues
on my shoulder mobility.
So when I reach around the back of my body to try to grab this strap when it's dangling,
I just want to grab it the one time.
I could probably fix that with some shoulder mobility exercises.
I just haven't yet.
But every once in a while, I'll get a little pinch, and it's real unpleasant.
So I just do it one time.
I don't know.
If you had a lot of shape to you, perhaps the two separate bands would be more useful.
I don't know how much difference in width a body can have over this much vertical space,
but potentially there.
So that's probably why they offer the two-band as well, so you can, you know, tighten the
top one a little bit more than the bottom one, or what have you.
All right, looking at the front of this thing.
So you've got your Velcro portion here that the cummerbund engages with, but there's actually
a little stretch pocket hidden behind that.
So I'll show you how that works.
You can absolutely fit an M4 mag in there if you want to.
I think it's going to be way small for a 152.
I could be wrong.
Nope.
Oh my gosh, that's easy.
152 fits in there no problem, which is very surprising.
Again, you're going to have height issues, so that may not be the preferred way to go.
But if for whatever reason you are using mil radios and want comms in a mag, you could
do comms in a mag in here really easy.
You're not going to conceal that thing very well, so I don't know.
But it fits.
If it fits, it ships, or something like that.
And then your cummerbunds, they have a little bit of a pocket in them.
So you've got this smaller pocket here, which I would imagine you could fit a pistol mag
in.
I have seemed to have misplaced all my pistol mags.
That's awkward.
But you can put a pistol mag in there.
It is open bottom, so take that into account.
And then you've got this larger pass-through here, which I think will still fit an M4 mag.
Oh, you know what?
I've got the perfect M4 mag for this.
Because they exist, we've got the cryoclips here, and that would be kind of a good use
for that thing, right?
Because it's open bottom, it'll keep your mag from disappearing on you.
And it fits no problem.
Internal on this thing, really nothing to write home about, but I'll show you just because.
You've got this kind of stretch panel here, which helps the fabric not need extra bulk
on it.
It curves around your torso very nicely.
It's very thin.
I would say that's less than a quarter of an inch.
It's incredibly thin.
So I don't know all the armor nerd stats on the performance of the soft armor, but I'm
sure you can look it up and translate it into whatever you need it to be.
Warranty period on these is going to be five years per the label.
I got a 2020 vest here, so I got three solid years left on this thing, but I don't know.
I know there's departments out there in the military that push soft armor way further
than they should, probably out of laziness and budget cuts.
But if you're buying it for yourself and you take good care of it, I'm sure that armor
will serve you well for several years after the fact, as long as you store it correctly
and don't beat it up, right?
But yeah, that's the Crye LVS.
These two pieces, they have the same elastic configuration on them.
They've got the smaller cell and then the M4 mag-sized cell, just in case you're wondering
about that.
And the Velcro orientation on these things, so obviously this is the front of the bag.
You've got this ribbon here to keep you from blowing out the elastic.
That's kind of a nice touch.
So really the only stretch is that little bit right there.
And then you've got a big chunk of loop that engages in that cummerbund pass-through on
the back.
So the two halves of the cummerbund are independent of each other, running through that plate
bag so that somewhere in there they marry up with hook Velcro inside the pass-through.
And then obviously there's nothing on the other side.
So you really just have to engage the one side.
Hopefully that made sense.
I kind of rambled a little bit there.
But this thing, super duper cool, all right?
Like I said in the intro, the videos that are out there are not overly helpful in really
selling this thing.
It's definitely a tough pill to swallow because you're looking at an $800-ish initial investment
for the soft armor and then the outer carrier itself.
Now if you're coming from the plate carrier world, it's exorbitantly expensive.
If you're coming from a other cut of soft armor, for example, I used bulks for a long
time and our bulks panels, I believe, were marketed at like $1,200.
So when you look at it from that perspective, it's really not an overly expensive setup
with the one caveat being you could have this for $800 and then wear any traditional plate
carrier that you wanted to over it, which does give you kind of the flexibility of you
could have the soft armor concealed and then throw on a JPC or whatever else you wanted
and you don't have to spend the $300-plus on the tactical cover for this thing.
So Cry hasn't done a great job of really selling the value of these things because there's,
you know, bulks exist and other armor cuts exist.
You could make an entry vest without having to dip into LVS territory.
But it is fairly quick to install if you didn't already have this concealed and have to go
through all that process to get it off.
Maybe, I don't know, maybe somehow you have multiples of these and you just want to keep
that full coverage armor in your plate carrier type setup.
I will say having come from bulks, this is a little bit more minimal.
You don't have the same extent of armor coming up into your shoulder pocket.
The wings are fairly similar sized, at least on the front.
The back wings are a little bit smaller than I remember bulks wings being, but very comfortable.
Super duper comfortable.
The soft armor by itself, you'll easily forget that you have it on.
The external carrier is still very comfortable.
This soft armor, because it's so thin, doesn't give you quite the same impression of having
some padding on as some of the other soft armor out there.
But that wasn't an issue at all when I was wearing this thing around.
And I wore it around a lot, as much as I could get away with not needing to wear armor anymore.
Just to get a feel for it.
Very comfortable.
I think you could ruck with it if you had to without too much issue.
Because there's really nothing, there's not a lot of bulk in the system and it's not adding
anything that would get in the way of the ruck.
Your wings are not huge.
They kind of fit very well.
They just protect your body from that 1M4 mag.
It would be kind of neat if they had that same stretch pocket somehow on the back here.
But I'm sure if you needed to, you could finagle kind of a wingman type pouch in here to get
something.
If you needed, I don't know, more magazine storage or something on that back plate.
But when you're wearing it concealed, you really don't need it.
Yeah, I don't know.
I guess the only thing really up in the air is the performance of the soft armor.
I trust that Crye's got pretty decent armor that they're selling with their label on it.
But I could be wrong.
There could be better performing soft armor.
So that's the Crye LVS.
I realize this is a very long video at this point in time.
I appreciate you guys for sticking around.
Hopefully you learned something.
And as always, I appreciate your time.
Thanks guys.
