RUPTamadre Shotgun Slug - This one scared me!

Ballistic Lab
1 follower
We test out the big and heavy RUPTamadre slug by Justin.
#BallisticLab #Ballistics #SlowMotion #ShotgunSlugs #HighSpeedCamera #12Gauge #BallisticTesting #Physics #TerminalBallistics
AI Generated·May contain errors
Video Summary
AI GeneratedJeff from Tau Fluttermouse tests the \"Ruptamadre,\" a heavy, 2-ounce steel hollow slug designed by Justin of the Oddity Realm. These projectiles feature a cavity for various fillers and a nose primer. Despite impressive impact power, the tests reveal significant stability issues and bore-fit problems due to the slugs being slightly oversized.
Hello, this is Jeff of Tau Fluttery Mouse
and on stage tonight we have in this very festive little
case, totally not a cave, the Ruptamadre.
This is a submission by Justin of the Oddity Realm
YouTube channel and these are some big and mean projectiles.
Made out of steel, each slug weighs
over two ounces. The length is just over 46 millimeters
or around 1 and 13 sixteenths of an inch
In fact, these...
Absolutely dwarf a regular 12-gauge foster slug.
The Reptimadre is a hollow slug with a steel plug on the nose.
Inside, we have a spacious cavity that can
be filled with liquids or other dry goods.
Now, Justin pre-filled most
of these with just some random stuff he had around the shop,
like old mill-end oil.
Special Taco Bell. I have no idea what that is.
Love that laser etching though. Next we have
steel blackening solution.
Then we have titanium and 304 powder.
One is filled with liquid latex.
Not sure what that's going to do.
It might be really interesting. And then he left a few of them
empty and he labeled those choose your own adventure.
And for these, we'll be using some antique propellant
and some metal shavings and other crap,
hoping to get a nice smoke effect and flames shooting out of the nose.
And all the slugs have been fitted with a 209 primer on the nose.
It was a perfect press fit.
Now, with such a long slug, we have
limited real estate inside the shell,
so we have to use a very short gas seal.
To support the tail, we use two short Sabos.
And then to support the nose we use a split kind
of a shot cup on the nose of it. This will also
protect the primer from being struck prematurely.
As you can see we just barely managed to fit all
this in this three inch hole. We'll be using 28 grains of steel powder.
And this should drive these to around 1,000 feet per second.
Trying to drive a two-ounce slug any faster than that,
well, the results would not end well.
Let's go out and test these out.
Hello, everyone. Welcome back. This is Jeff of Tau Flatermouse.
Today, we're going to be testing out the Rupta Madre.
Very big, heavy slug.
We only got eight of them,
so this should only take a couple hours to film.
get the heck out of here but it's
a beautiful day it's like 70 degrees beautiful and very sunny so
that's going to help with the high speed uh
but the first thing we want to do is to do a
calibration shot at 20 yards with a standard foster slug
that's uh that's how we check to
see if the red dot
is still zeroed okay calibration
so as you can see we are a little bit off we're
About two inches low, maybe an inch to the left.
Now we can make a little adjustment to the red dot
and we should be in the ballpark.
Okay our first Rupta Madre will be the one with the
the blackening chemical in there.
It's used to turn steel black. I guess it's kind of like bluing
but this is supposed to make it black
so we got a mild steel plate out there on the dummy.
And we'll see if it'll rupture and blacken that plate,
or if it'll just go right through it.
Two ounces of solid steel is something else.
Okay, here we go.
This thing is flying off
to the right.
Elevation is great.
We got that down.
But kind of looks like it hit kind of obliquely there.
Just punched right through that steel plate, though.
And then, of course, exited right about here.
Here, this is kind of...
Changed angles and everything.
Big, big hole there, but no rupturing, no rupturing. We might
need something a little harder.
Let's take a look at the high-speed footage and see how this thing
actually flew. Now we can see that the slug is flying at an angle,
and if you look at the stripe
on the back of the slug, that is not spinning at all.
Remarkably, it straightened out in the last millisecond
and hit nose first.
Immediately after impact, we could see the slug exiting
and leaving a trail of chemicals behind it, so it did rupture.
We could also see the slug of steel punched out from the plate,
which has become a formidable projectile of its own.
Overall, pretty impressive performance
for a 2-ounce projectile traveling only around 1,000 feet per second.
That's 681 miles per hour.
I think we can agree
this is a little bit of a harder target.
Big slab of concrete.
It's that thick.
Probably 5 inches thick.
Just going to aim at the center of it.
This one has the titanium powder in it.
We'll see if that ruptures or not.
Titanium powder! Here we go.
Not terrible, not bad.
I mean it it created some new cracks in the... It tried. I mean
there are some serious cracks there.
That's a lot of a lot of rock inside there. That
Foster slug probably would have put a little dent like that in there,
but nice big impact.
In this test, we had much improved stability of the projectile.
It did hit nose first. The
The accuracy was a little bit off.
It shot a little bit high and to the right.
We also see that the slug is rotating not a lot
but it is helping with the stability.
Right after impact we see a glimpse of the slug it is very deformed
and the nose is smashed and that
is the last we'll ever see of that slug it just bounced off.
Kind of lucky it didn't come right
back at me to be honest with you.
Now the cracks in the slab were substantial enough that when I
Uh, removed it from the table and dropped it on the ground.
Big chunks of it broke off.
Okay, the next one
is the one full of latex.
Okay, at the lead plate.
Here we go. Good hit.
Good solid hit. Here we go. Absolutely sideways.
Get it close. And it buried itself in there.
I don't know if I can get that out, but it is.
There's a bulge right there.
It's part of the copper little gasket.
I think you can see latex on there but it's possible
because there was a liquid in there
it prevented it from spinning up and stabilizing that's just a theory.
Now this test the slug was
just absolutely out of control no stability at all.
Now Justin made these slightly out of spec
with a diameter of 0.685 inches.
The nominal diameter that we're looking for is between 0.675
And point 680.
and to be honest i thought that 0.685 would still work
but the bore fit is just a little too tight
this creates a pressure problem causing the gas seal to blow out
and the hot gases cook the sabos
so we lose all bore contact okay next up
is the Taco Bell hot sauce or whatever that it might be
code for something it may actually be Taco Bell hot sauce we don't know
but we're gonna fire at
Fire at the aluminum plate.
See if we can get it to splatter.
Here we go.
Here we go.
Can you see where it hit?
Why?
There it is.
Accuracy was decent.
I was aiming about right here.
That's our impact.
Actually left an impression of the hex
from the Allen's pocket, I guess you'd call it.
You saw a little flash there.
I put a primer in every one of these, and it just made a little flash.
Now in this test we actually had a pretty decent and clean launch.
The stability was
very good on this one.
Even though we had almost no spin at all on this one,
the little groove that Justin put on there kind of acted like a
skirt on an air rifle pellet,
giving it enough stability to stay flying straight. So sometimes
we get lucky, sometimes not so lucky.
But I still don't know what special Taco Bell is.
Here is the one that hit the aluminum plate.
We found the little cap. Actually hit something that
was on there. Ripped the threads right out of it.
Pretty cool. At least it ruptured. It officially
ruptured. Well it is pumpkin weather
and we're gonna fire some pumpkin spice at this thing. We've
gotten to the point where the ones that I put
the the spice in are up next. We got three of those.
We're firing at the wet catalogs, I say magazines,
they're catalogs, different type of paper I should say.
Steel plate behind there to capture anything that might come through.
It's time for the spice.
Put the spice in the pumpkin, here we go.
Whoa, boy. Put the spice in the pumpkin, here we go.
Well that was a big surprise.
Okay so they grazed the edge there.
I was aiming way over here remember?
But it was flying all wonky
so that all bets are off once it starts flying wonky.
Then it hit the steel plate behind her left a big big big dent in it.
Then it detonated
and uh found a piece of it.
So uh yeah I guess that uh gives you
an idea what it looks like inside.
Boy these this kind of scares me now.
Oh my goodness.
Well, this one definitely did not function as designed.
Remember, it was supposed to just produce some smoke
and a jet of flames coming out of the nose,
but all hell broke loose on this one.
But luckily, I put that steel plate behind there,
giving it something to hit.
I guess if you're going to have a failure,
you might as well go out big.
But definitely scary stuff right there.
This is the first sloth head skull.
The ballistic skull there, yeah, it's a little wonky.
We had a little malfunction
in the casting.
It's kind of like, it's kind of like the first pancake,
you know, it never comes out right.
But we're gonna fire it anyway,
cause it's just, oh, there ain't gonna be much left
after we shoot it.
We're gonna
send some spice
into that thing.
Well, that one went right over his head.
Here we go.
Now in this shot we could actually see
the condition of the sabos. They are all shredded.
There goes the gas seal, that white object there, and it is damaged.
Now this projectile was actually full
of the oil out of his milling machine,
but I guess we should be happy that it even hit.
That thing was just very unstable
and flying sideways right through the head.
Okay, spice baby, spice!
Now this one again we have the sabos all shredded up
but this is definitely one of the spice ones
with the red nose on it.
Now the most important thing we learned in these tests is that there is
a limit to how large of a diameter we can make
these things 0.685 is definitely a little too fat.
Fortunately it doesn't create a dangerous condition for the gun.
The Sabos just take all the abuse
and act like a kind of a pressure relief valve by blowing out.
Okay so it's entered right here in the skull.
Looks like it I think it hit sideways too.
These things really had a stability problem.
There was a kind of a conundrum going on there
and that's it. So now we we know the rest of the story.
I hope you guys enjoyed this.
Kind of a frustrating day,
I am not as happy as a hobo in a hot tub, but at least we got
some cool hits today.
Hope you enjoyed the video anyway, we'll see you next time.
